dgiese / dustcloud-documentation Goto Github PK

Hi,

Do you think restore will factory reset the gateway?

https://github.com/dgiese/dustcloud-documentation/tree/master/roborock.vacuum.s5/firmware points to https://dustcloud.seemoo.de/public/xiaomi.vacuum.gen2 which only yields a 403.

I have a fan of zhimi.fan.v2. The spi flash is damaged. Can you please download the firmware by creating a hotspot and using wireshark to capture packets(When Mi Home shows that the fan could upgrade the firmware)?

I have another fan of zhimi.fan.v3, but the circuit is different from v2.

I'm sorry to send the help information here. I hope someone can help me. Thank you.

Hi,
After few restarts directly from power my Gateway ZHWG11LM not boot I receive this error:

NAND read: device 0 offset 0x300000, size 0x700000
7340032 bytes read: OK

NAND read: device 0 offset 0xa00000, size 0x100000
1048576 bytes read: OK
Kernel image @ 0x80800000 [ 0x000000 - 0x617290 ]

Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Using Device Tree in place at 83000000, end 8300c0e1
Modify /soc/aips-bus@02000000/tsc@02040000:status disabled
Modify /soc/aips-bus@02000000/can@02090000:status disabled
Modify /soc/aips-bus@02000000/can@02094000:status disabled
Modify /soc/aips-bus@02100000/lcdif@021c8000:status disabled
Modify /soc/aips-bus@02100000/pxp@021cc000:status disabled
Modify /soc/aips-bus@02100000/csi@021c4000:status disabled
Modify /soc/aips-bus@02000000/ethernet@020b4000:status disabled
Modify /soc/aips-bus@02100000/usb@02184200:status disabled
Modify /soc/aips-bus@02000000/spba-bus@02000000/sai@0202c000:status disabled
Modify /soc/aips-bus@02000000/spba-bus@02000000/sai@02030000:status disabled
Modify /soc/aips-bus@02100000/serial@021f4000:status disabled
Modify /soc/aips-bus@02100000/serial@021fc000:status disabled
Modify /soc/aips-bus@02000000/spba-bus@02000000/serial@02018000:status disabled
Modify /soc/aips-bus@02000000/pwm@020f0000:status disabled
Modify /soc/aips-bus@02000000/pwm@020f4000:status disabled
Modify /soc/aips-bus@02000000/pwm@020f8000:status disabled
Modify /soc/aips-bus@02000000/pwm@020fc000:status disabled
Modify /soc/aips-bus@02000000/spba-bus@02000000/ecspi@02010000:status disabled
Modify /soc/aips-bus@02000000/spba-bus@02000000/ecspi@02014000:status disabled
Modify /soc/aips-bus@02100000/i2c@021a8000:status disabled
Modify /soc/aips-bus@02100000/i2c@021f8000:status disabled
Modify /soc/aips-bus@02000000/gpt@020e8000:status disabled
Modify /soc/aips-bus@02000000/epit@020d4000:status disabled
ft_system_setup for mx6
No PMIC found!

Starting kernel …

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.1.15+gb63f3f5 (chenlong@gitlab) (gcc version 5.3.0 (GCC) ) #37 SMP PREEMPT Tue Jun 19 15:28:38 CST 2018
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Freescale i.MX6 ULL 14x14 EVK Board
[ 0.000000] Reserved memory: failed to allocate memory for node ‘linux,cma’
[ 0.000000] cma: Reserved 96 MiB at 0x8a000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 12 pages/cpu @89da3000 s16908 r8192 d24052 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttymxc0,115200 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs cma=96M mtdparts=gpmi-nand:3m(boot),7m(kernel),1m(dtb),-(rootfs)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 148920K/262144K available (8035K kernel code, 423K rwdata, 2812K rodata, 540K init, 426K bss, 14920K reserved, 98304K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0x90800000 - 0xff000000 (1768 MB)
[ 0.000000] lowmem : 0x80000000 - 0x90000000 ( 256 MB)
[ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
[ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
[ 0.000000] .text : 0x80008000 - 0x80aa01f8 (10849 kB)
[ 0.000000] .init : 0x80aa1000 - 0x80b28000 ( 540 kB)
[ 0.000000] .data : 0x80b28000 - 0x80b91fa0 ( 424 kB)
[ 0.000000] .bss : 0x80b94000 - 0x80bfeb5c ( 427 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] mxc_clocksource_init 24000000
[ 0.000000] Switching to timer-based delay loop, resolution 41ns
[ 0.000016] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[ 0.000056] clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.002576] Console: colour dummy device 80x30
[ 0.002616] Calibrating delay loop (skipped), value calculated using timer frequency… 48.00 BogoMIPS (lpj=240000)
[ 0.002651] pid_max: default: 32768 minimum: 301
[ 0.002874] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.002904] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.004265] CPU: Testing write buffer coherency: ok
[ 0.004756] /cpus/cpu@0 missing clock-frequency property
[ 0.004799] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.004905] Setting up static identity map for 0x80008280 - 0x800082d8
[ 0.041169] Brought up 1 CPUs
[ 0.041209] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[ 0.041228] CPU: All CPU(s) started in SVC mode.
[ 0.042327] devtmpfs: initialized
[ 0.063971] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.064862] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.072754] pinctrl core: initialized pinctrl subsystem
[ 0.075452] NET: Registered protocol family 16
[ 0.093567] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.120887] cpuidle: using governor ladder
[ 0.150951] cpuidle: using governor menu
[ 0.193715] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.193752] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.196952] imx6ul-pinctrl 20e0000.iomuxc: Invalid fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/imx6ul-evk/hoggrp-1
[ 0.197656] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.198341] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[ 0.258317] mxs-dma 1804000.dma-apbh: initialized
[ 0.264987] SCSI subsystem initialized
[ 0.266435] usbcore: registered new interface driver usbfs
[ 0.266640] usbcore: registered new interface driver hub
[ 0.266863] usbcore: registered new device driver usb
[ 0.269399] i2c i2c-0: IMX I2C adapter registered
[ 0.269446] i2c i2c-0: can’t use DMA
[ 0.270994] i2c i2c-1: IMX I2C adapter registered
[ 0.271034] i2c i2c-1: can’t use DMA
[ 0.271337] Linux video capture interface: v2.00
[ 0.271572] pps_core: LinuxPPS API ver. 1 registered
[ 0.271769] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [email protected]
[ 0.271878] PTP clock support registered
[ 0.274568] MIPI CSI2 driver module loaded
[ 0.275265] Advanced Linux Sound Architecture Driver Initialized.
[ 0.277417] Bluetooth: Core ver 2.20
[ 0.277545] NET: Registered protocol family 31
[ 0.277569] Bluetooth: HCI device and connection manager initialized
[ 0.277609] Bluetooth: HCI socket layer initialized
[ 0.277644] Bluetooth: L2CAP socket layer initialized
[ 0.277728] Bluetooth: SCO socket layer initialized
[ 0.279868] Switched to clocksource mxc_timer1
[ 0.306640] NET: Registered protocol family 2
[ 0.308274] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.308377] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.308471] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.308613] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.308679] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.309103] NET: Registered protocol family 1
[ 0.312505] imx rpmsg driver is registered.
[ 0.315204] Bus freq driver module loaded
[ 0.317538] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.335656] VFS: Disk quotas dquot_6.6.0
[ 0.336117] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.340410] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.342192] fuse init (API version 7.23)
[ 0.353394] io scheduler noop registered
[ 0.353443] io scheduler deadline registered
[ 0.353980] io scheduler cfq registered (default)
[ 0.354999] imx-weim 21b8000.weim: Driver registered.
[ 0.359519] lumi_r supply power not found, using dummy regulator
[ 0.361706] lumi_b supply power not found, using dummy regulator
[ 0.363475] lumi_g supply power not found, using dummy regulator
[ 0.365765] MIPI DSI driver module loaded
[ 0.366209] MIPI DSI driver module loaded
[ 0.372032] imx-sdma 20ec000.sdma: no event needs to be remapped
[ 0.372246] imx-sdma 20ec000.sdma: loaded firmware 3.3
[ 0.380235] imx-sdma 20ec000.sdma: initialized
[ 0.382307] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 19, base_baud = 5000000) is a IMX
[ 1.031579] console [ttymxc0] enabled
[ 1.037098] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 217, base_baud = 5000000) is a IMX
[ 1.083028] imx-rng 2284000.rngb: iMX RNG Registered.
[ 1.088751] imx sema4 driver is registered.
[ 1.093242] [drm] Initialized drm 1.1.0 20060810
[ 1.099198] [drm] Initialized vivante 1.0.0 20120216 on minor 0
[ 1.132006] brd: module loaded
[ 1.148908] loop: module loaded
[ 1.152890] pn54x_dev_init–>lumi
[ 1.156415] pn54x_probe
[ 1.158938] pn544 1-0028: FIRM GPIO error getting from OF node
[ 1.165933] pn544 1-0028: CLKREQ GPIO error getting from OF node
[ 1.173008] 1-0028 supply nxp,pn54x-pvdd not found, using dummy regulator
[ 1.180028] 1-0028 supply nxp,pn54x-vbat not found, using dummy regulator
[ 1.186984] 1-0028 supply nxp,pn54x-pmuvcc not found, using dummy regulator
[ 1.194147] 1-0028 supply nxp,pn54x-sevdd not found, using dummy regulator
[ 1.201197] pn54x_probe: request irq_gpio 7
[ 1.205424] pn54x_probe: request ven_gpio 3
[ 1.210117] pn54x_probe : requesting IRQ 35
[ 1.229638] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.236131] nand: Micron MT29F2G08ABAEAWP
[ 1.240229] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.248624] gpmi-nand 1806000.gpmi-nand: enable the asynchronous EDO mode 5
[ 1.256103] Bad block table found at page 131008, version 0x01
[ 1.262247] Bad block table found at page 130944, version 0x01
[ 1.268481] 4 cmdlinepart partitions found on MTD device gpmi-nand
[ 1.274766] Creating 4 MTD partitions on “gpmi-nand”:
[ 1.279912] 0x000000000000-0x000000300000 : “boot”
[ 1.287355] 0x000000300000-0x000000a00000 : “kernel”
[ 1.294873] 0x000000a00000-0x000000b00000 : “dtb”
[ 1.302142] 0x000000b00000-0x000010000000 : “rootfs”
[ 1.310535] gpmi-nand 1806000.gpmi-nand: driver registered.
[ 1.322521] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 1.329124] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 1.335043] usbcore: registered new interface driver usb-storage
[ 1.341344] usbcore: registered new interface driver usb_ehset_test
[ 1.350265] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
[ 1.359330] 2184000.usb supply vbus not found, using dummy regulator
[ 1.373926] mousedev: PS/2 mouse device common for all mice
[ 1.381668] input: 20cc000.snvs:snvs-powerkey as /devices/platform/soc/2000000.aips-bus/20cc000.snvs/20cc000.snvs:snvs-powerkey/input/input0
[ 1.399447] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc0
[ 1.408661] i2c /dev entries driver
[ 1.415101] IR NEC protocol handler initialized
[ 1.419698] IR RC5(x/sz) protocol handler initialized
[ 1.424893] IR RC6 protocol handler initialized
[ 1.429478] IR JVC protocol handler initialized
[ 1.434101] IR Sony protocol handler initialized
[ 1.438767] IR SANYO protocol handler initialized
[ 1.443560] IR Sharp protocol handler initialized
[ 1.448310] IR MCE Keyboard/mouse protocol handler initialized
[ 1.454229] IR XMP protocol handler initialized
[ 1.465046] imx2-wdt 20bc000.wdog: use WDOG_B to reboot.
[ 1.471443] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[ 1.478711] sdhci: Secure Digital Host Controller Interface driver
[ 1.485045] sdhci: Copyright© Pierre Ossman
[ 1.489464] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.496920] /soc/aips-bus@02100000/usdhc@02190000: voltage-ranges unspecified
[ 1.504210] sdhci-esdhc-imx 2190000.usdhc: could not get ultra high speed state, work on normal mode
[ 1.514815] sdhci-esdhc-imx 2190000.usdhc: No vmmc regulator found
[ 1.521112] sdhci-esdhc-imx 2190000.usdhc: No vqmmc regulator found
[ 1.570119] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[ 1.604256] usbcore: registered new interface driver usbhid
[ 1.610220] usbhid: USB HID core driver
[ 1.614897] vf610-adc 2198000.adc: Debug vf610_adc_proble()
[ 1.621221] 2198000.adc supply vref not found, using dummy regulator
[ 1.627897] vf610-adc 2198000.adc: Debug[0] channels[2]
[ 1.642470] wm8524_i2c_probe:
[ 1.650075] mmc0: new high speed SDIO card at address 0001
[ 1.656518] wm8960 1-001a: Failed to issue reset
[ 1.661580] wm8960: probe of 1-001a failed with error -5
[ 1.670288] fsl-asrc 2034000.asrc: driver registered
[ 1.683143] imx_wm8524_probe:
[ 1.686831] wm8524_probe:
[ 1.691053] imx-wm8524 sound2: wm8524-hifi <-> 2028000.sai mapping ok
[ 1.698946] imx-wm8524 sound2: snd-soc-dummy-dai <-> 2034000.asrc mapping ok
[ 1.706552] imx-wm8524 sound2: wm8524-hifi <-> 2028000.sai mapping ok
[ 1.720237] NET: Registered protocol family 26
[ 1.726865] NET: Registered protocol family 10
[ 1.733656] sit: IPv6 over IPv4 tunneling driver
[ 1.740370] NET: Registered protocol family 17
[ 1.745188] Bluetooth: RFCOMM TTY layer initialized
[ 1.750342] Bluetooth: RFCOMM socket layer initialized
[ 1.755557] Bluetooth: RFCOMM ver 1.11
[ 1.759372] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.764786] Bluetooth: BNEP filters: protocol multicast
[ 1.770111] Bluetooth: BNEP socket layer initialized
[ 1.775125] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.781137] Bluetooth: HIDP socket layer initialized
[ 1.786153] 8021q: 802.1Q VLAN Support v1.8
[ 1.790466] lib80211: common routines for IEEE802.11 drivers
[ 1.796375] Key type dns_resolver registered
[ 1.802609] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 1.837445] ubi0: attaching mtd3
[ 2.168058] random: nonblocking pool is initialized
[ 2.525994] ubi0: scanning is finished
[ 2.544530] ubi0: attached mtd3 (name “rootfs”, size 245 MiB)
[ 2.550803] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.557708] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.564576] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.571606] ubi0: good PEBs: 1956, bad PEBs: 4, corrupted PEBs: 0
[ 2.577723] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 2.585075] ubi0: max/mean erase counter: 68/19, WL threshold: 4096, image sequence number: 1039097381
[ 2.594447] ubi0: available PEBs: 0, total reserved PEBs: 1956, PEBs reserved for bad PEB handling: 36
[ 2.603828] ubi0: background thread “ubi_bgt0d” started, PID 73
[ 2.609819] dhd_module_init in
[ 2.614667] input: regulators:gpio-keys as /devices/platform/regulators/regulators:gpio-keys/input/input1
[ 2.625013] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01 00:00:01 UTC (1)
[ 2.655067] gpio_dvfs: disabling
[ 2.658349] vref-3v3: disabling
[ 2.661609] can-3v3: disabling
[ 2.665042] ALSA device list:
[ 2.668034] #0: wm8524-audio
[ 2.692611] UBIFS (ubi0:0): recovery needed
[ 2.707926] UBIFS error (ubi0:0 pid 1): replay_log_leb: bad sqnum 2340065, commit sqnum 2344308
[ 2.716746] UBIFS error (ubi0:0 pid 1): replay_log_leb: log error detected while replaying the log at LEB 8:2048
[ 2.726985] magic 0x6101831
[ 2.730717] crc 0x4d441810
[ 2.734481] node_type 7 (master node)
[ 2.738674] group_type 0 (no node group)
[ 2.743080] sqnum 2340065
[ 2.746579] len 512
[ 2.749730] highest_inum 8477
[ 2.753014] commit number 23552
[ 2.756339] flags 0x3
[ 2.759489] log_lnum 4
[ 2.762500] root_lnum 1903
[ 2.765739] root_offs 107096
[ 2.769150] root_len 108
[ 2.772334] gc_lnum 1082
[ 2.775574] ihead_lnum 1903
[ 2.778811] ihead_offs 108544
[ 2.782254] index_size 1723680
[ 2.785753] lpt_lnum 9
[ 2.788729] lpt_offs 10490
[ 2.792082] nhead_lnum 9
[ 2.795060] nhead_offs 12288
[ 2.798384] ltab_lnum 9
[ 2.801399] ltab_offs 10240
[ 2.804724] lsave_lnum 0
[ 2.807702] lsave_offs 0
[ 2.810711] lscan_lnum 1085
[ 2.813950] leb_cnt 1916
[ 2.817185] empty_lebs 738
[ 2.820366] idx_lebs 40
[ 2.823430] total_free 93884416
[ 2.827016] total_dirty 21318224
[ 2.830629] total_used 124709008
[ 2.834304] total_dead 806672
[ 2.837714] total_dark 5946544
[ 2.841810] List of all partitions:
[ 2.845339] 0100 65536 ram0 (driver?)
[ 2.850141] 0101 65536 ram1 (driver?)
[ 2.854804] 0102 65536 ram2 (driver?)
[ 2.859457] 0103 65536 ram3 (driver?)
[ 2.864204] 0104 65536 ram4 (driver?)
[ 2.868860] 0105 65536 ram5 (driver?)
[ 2.873602] 0106 65536 ram6 (driver?)
[ 2.878254] 0107 65536 ram7 (driver?)
[ 2.882948] 0108 65536 ram8 (driver?)
[ 2.887601] 0109 65536 ram9 (driver?)
[ 2.892290] 010a 65536 ram10 (driver?)
[ 2.897031] 010b 65536 ram11 (driver?)
[ 2.901806] 010c 65536 ram12 (driver?)
[ 2.906549] 010d 65536 ram13 (driver?)
[ 2.911322] 010e 65536 ram14 (driver?)
[ 2.916060] 010f 65536 ram15 (driver?)
[ 2.920844] 1f00 3072 mtdblock0 (driver?)
[ 2.925934] 1f01 7168 mtdblock1 (driver?)
[ 2.931119] 1f02 1024 mtdblock2 (driver?)
[ 2.936209] 1f03 250880 mtdblock3 (driver?)
[ 2.941328] No filesystem could mount root, tried: ubifs
[ 2.946784] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 2.955070] —[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

Any idea how to fix this?

Tnx,
Prontoo

Hello, the link to the firmware does not work. I need to flash the robo gen1.