xyzroe / xzg Goto Github PK

Describe the bug
Getting warnings in HA when using Ethernet without WiFi:
Template variable warning: 'dict object' has no attribute 'wlanSsid' when rendering '{{ value_json.wlanSsid }}'

To Reproduce
Steps to reproduce the behavior:

1. Only connect over Ethernet
2. Check HA logs

Expected behavior
Shouldn't get these warnings while only connected over Ethernet.

Screenshots

Logger: homeassistant.helpers.template
Source: helpers/template.py:2613
First occurred: 20 mai 2024 la 20:18:52 (1427 occurrences)
Last logged: 19:56:18

Template variable warning: 'dict object' has no attribute 'wlanSsid' when rendering '{{ value_json.wlanSsid }}'

Additional context
Olimex-ESP32-POE
20240519

WiFi / VPN page in specific. Attached an example

So when I first upgrade the firmware and I am using Static IP, when I click to the IP setting page it is showing the default IP settings instead of what's being defined from previous firmware, I had mine switched from Static IP to DHCP and now IP info shows correctly.

In the previous firmware 0.26 and prior, MQTT configuration used to send the IP address of the coordinator

To Reproduce
Steps to reproduce the behavior:

1. Upgrade to XZG firmware
2. Enable MQTT Configuration

Expected behavior
IP Address as part of MQTT Payload

Screenshots
If applicable, add screenshots to help explain your problem.

Additional context
Add any other context about the problem here.

Hi there! ✌️

I would like to c 12 hourly format for displaying time in the web.

This is not an absolutely urgent feature request, so we can move it somewhere to the end of to-do list. 😉

Thank u in advance!

Today I updated via LAN my ZigStar Lan Gateway.
Device model WT32-ETH01
FW revision 20240510
HW version ESP32-D0WD
The device is recognized by iobroker, but the connection is offline every 30 to 60 minutes. After a few minutes it is online again, but the adapter (zigbee.iobroker) in the iobroker remains yellow. Only after restarting the adapter will it turn green again.

Пробовал несколько раз разные прошивки - процесс идет до 75-95% и после этого устройство полностью отваливается (и по ping в том числе). Принудительно передергиваю по питанию (POE) - в окне статус "FW версия" либо пусто, либо 0
Пришлось прошивать через ZigStarGW-MT-x64

I had my UZG01 just updated to the XZG firmware and found I am unable to connect to the Web UI using HAProxy.

Any idea please?

Hi!

MQTT sensor of gateway zigbee firmware version displaying 0:

After update from 0.2.6 can't access web ui by fqdn; opening http://uzg-01/ redirects to 192.168.1.1 but my local address pool is in 10.0.0.0 range; Chrome, Firefox, Edge

Splitting this off into a separate issue as it doesn't appear to match what @rombrock reported in theirs:

I wasn't able to get FW 20240508/20240509 to work on my ZigStar LAN PoE gateway because the LAN connection would not work. It worked once immediately after flash with DHCP, and then never again. No combination of LAN DHCP or static IP address settings would make the LAN connection come up, and I tried re-flashing the firmware multiple times. (I also wasn't able to connect it to my Wi-Fi, though that may be normal as I've never used Wi-Fi before on it.) I rolled back to the old firmware and the device started working normally again.

Hardware and previous firmware:
FW version : 0.6.10
Hardware : TTGO T-Internet-POE
ESP32 model : ESP32-D0WDQ5

HW as shown in the XZG firmware:
Device model: Olimex-ESP32-POE
FW revision: 20240519
HW version: ESP32-D0WD

Originally posted by @Steltek in #11 (comment)

In the General section when selecting "USB mode" after saving in "Operating mode 2" and connecting from z2m via USB does not work. Experimentally found out that if you set value="1" instead of value="2" in the HTML code of the element selecting USB mode, then after sending the form and saving "Operating mode Zigbee-USB".

Is your feature request related to a problem? Please describe.
Missing support for WPA3-Personal
I've recently upgraded my wireless router and I was wanting to utilize wireless connection on my ZigStarGW.

Describe the solution you'd like
Update FW on ESP32 to support WPA3-Personal if possible
https://docs.espressif.com/projects/esp-idf/en/latest/esp32/api-guides/wifi-security.html#wpa3-personal

Describe alternatives you've considered

Additional context
https://imgur.com/gb6jt4i