Comments (22)
Hello everyone, I reinstalled the old firmware and the connection is now stable again. No failure for over an hour, with the new version (FW revision 20240510) there were interruptions about every 45 minutes.
FW version: 0.6.10
Hardware: WT32-ETH01
ESP32 model: ESP32-D0WDQ5
I didn't change anything, no replacing the power supply.
from xzg.
Chiming in: I wasn't able to get FW 20240508/20240509 to work on my ZigStar LAN PoE gateway because the LAN connection would not work. It worked once immediately after flash with DHCP, and then never again. No combination of LAN DHCP or static IP address settings would make the LAN connection come up, and I tried re-flashing the firmware multiple times. (I also wasn't able to connect it to my Wi-Fi, though that may be normal as I've never used Wi-Fi before on it.) I rolled back to the old firmware and the device started working normally again.
Hardware and previous firmware:
FW version : 0.6.10
Hardware : TTGO T-Internet-POE
ESP32 model : ESP32-D0WDQ5
from xzg.
Today I updated via LAN my ZigStar Lan Gateway. Device model WT32-ETH01 FW revision 20240510 HW version ESP32-D0WD The device is recognized by iobroker, but the connection is offline every 30 to 60 minutes. After a few minutes it is online again, but the adapter (zigbee.iobroker) in the iobroker remains yellow. Only after restarting the adapter will it turn green again.
- You mean socket connection to Zigbee module, right?
- How about uptime of the gateway? Does is drops to 0 after connection goes offline?
from xzg.
Chiming in: I wasn't able to get FW 20240508/20240509 to work on my ZigStar LAN PoE gateway because the LAN connection would not work. It worked once immediately after flash with DHCP, and then never again. No combination of LAN DHCP or static IP address settings would make the LAN connection come up, and I tried re-flashing the firmware multiple times. (I also wasn't able to connect it to my Wi-Fi, though that may be normal as I've never used Wi-Fi before on it.) I rolled back to the old firmware and the device started working normally again.
Hardware and previous firmware: FW version : 0.6.10 Hardware : TTGO T-Internet-POE ESP32 model : ESP32-D0WDQ5
I need a little bit more information.
- Right after flashing it started ok, what device model was shown in web UI?
- If there isn't any connection for more that 60 seconds WiFi AP will start. Than you can check the device model and lan settings.
- Also check device model when LAN doesn't start successfully.
from xzg.
I need a little bit more information.
1. Right after flashing it started ok, what device model was shown in web UI? 2. If there isn't any connection for more that 60 seconds WiFi AP will start. Than you can check the device model and lan settings. 3. Also check device model when LAN doesn't start successfully.
Right after upgrading, no LAN connected yet, only USB:
Device model: Olimex-ESP32-POE
FW revision: 20240510
HW version: ESP32-D0WD
Unplugged USB (power down) and plugged in Ethernet PoE. Device booted and took an IP from the DHCPd. Model info etc stayed the same.
Changing the network configuration to static (DHCP off, IP 192.168.1.x, gateway 192.168.1.y, DNS servers 1.1.1.1 and 8.8.8.8) and rebooting: No more LAN connection. (Orange LED on for 2-3 seconds, then green LED comes on and the orange LED is blinking for a second, back to orange LED on, .... loop. The interface on the switch side never shows a link.) The XZG... AP appears but I either can't connect to it, or get disconnected immediately after connecting. (Feels like the device is in a boot/crash loop.)
Update: Same symptoms on a non-PoE interface.
Serial/USB console output:
11303 [NetworkEvent] ETH MAC: A8:03:2A:aa:bb:cc, IP: 192.168.1.x, Mask: 255.255.255.0, Gw: 192.168.1.y, 100Mbps
21303 [NetworkEvent] ETH MAC: A8:03:2A:aa:bb:cc, IP: 192.168.1.x, Mask: 255.255.255.0, Gw: 192.168.1.y, 100Mbps
31303 [NetworkEvent] ETH MAC: A8:03:2A:aa:bb:cc, IP: 192.168.1.x, Mask: 255.255.255.0, Gw: 192.168.1.y, 100Mbps
41328 [NetworkEvent] ETH MAC: A8:03:2A:aa:bb:cc, IP: 192.168.1.x, Mask: 255.255.255.0, Gw: 192.168.1.y, 100Mbps
51383 [NetworkEvent] ETH MAC: A8:03:2A:aa:bb:cc, IP: 192.168.1.x, Mask: 255.255.255.0, Gw: 192.168.1.y, 100Mbps
61329 [NetworkEvent] ETH MAC: A8:03:2A:aa:bb:cc, IP: 192.168.1.x, Mask: 255.255.255.0, Gw: 192.168.1.y, 100Mbps
71329 [NetworkEvent] ETH MAC: A8:03:2A:aa:bb:cc, IP: 192.168.1.x, Mask: 255.255.255.0, Gw: 192.168.1.y, 100Mbps
79329 [NetworkEvent] ETH MAC: A8:03:2A:aa:bb:cc, IP: 192.168.1.x, Mask: 255.255.255.0, Gw: 192.168.1.y, 100Mbps
89328 [NetworkEvent] ETH MAC: A8:03:2A:aa:bb:cc, IP: 192.168.1.x, Mask: 255.255.255.0, Gw: 192.168.1.y, 100Mbps
105383 [NetworkEvent] ETH MAC: A8:03:2A:aa:bb:cc, IP: 192.168.1.x, Mask: 255.255.255.0, Gw: 192.168.1.y, 100Mbps
115328 [NetworkEvent] ETH MAC: A8:03:2A:aa:bb:cc, IP: 192.168.1.x, Mask: 255.255.255.0, Gw: 192.168.1.y, 100Mbps
abort() was called at PC 0x40175a4f on core 0
Backtrace: 0x400827d9:0x3ffd0680 0x4008c921:0x3ffd06a0 0x4008ff0d:0x3ffd06c0 0x40175a4f:0x3ffd0740 0x40175a96:0x3ffd0760 0x40176219:0x3ffd0780 0x40175ac8:0x3ffd07a0 0x400f1af6:0x3ffd07c0 0x400f1ba1:0x3ffd0810 0x400f1bf2:0x3ffd0860 0x400e05fb:0x3ffd08a0 0x400d9833:0x3ffd0900 0x400d98ec:0x3ffd0930 0x400e75f3:0x3ffd0a00 0x400e783c:0x3ffd0b90
ELF file SHA256: 0000000000000000
Rebooting...
ets Jun 8 2016 00:22:57
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
Update 2: After this, re-flashing the firmware does not make LAN work again. Problem with the link remains the same. Blinking sequence is the same. It is possible to get in via Wi-Fi by unplugging the LAN interface, and I can confirm the LAN settings are back to default (Ethernet Enabled, DHCP enabled), but link will no longer establish. It looks like the only way to make the LAN connection work again with DHCP is to go back to the old ZigStar GW firmware, and then to XZG.
from xzg.
The main problem is from board detecting mechanism. Just because of unplugged LAN cable during first boot. You could try to factory reset using tools page, with plugged in LAN cable.
Also pay attention on device model on root page if any problems.
from xzg.
I flashed version 20240519 via USB with the network (without PoE) attached.
First reboot happened, and the device did not manage to connect to the network (Link on the switch did not come up, DHCP logged no request). ()
Factory reset did not change anything. ()
Disconnect USB and Ethernet, then plugged in Ethernet with PoE.
No link, no DHCP request. ()
Performed factory reset. Did not change anything. ()
(*) The device remains stuck like before, the yellow Ethernet light is on for a few seconds, then the green one turns on and the yellow one blinks for a second, then the green one turns off and the yellow one stays on normally again (keeps looping like that).
Hardware in the WebUI still shows the same:
Device model: Olimex-ESP32-POE
FW revision: 20240519
HW version: ESP32-D0WD
from xzg.
My issue doesn't appear to match with what @rombrock reported above, so I've split it off into #16 to avoid further polluting this one.
from xzg.
Today I updated via LAN my ZigStar Lan Gateway. Device model WT32-ETH01 FW revision 20240510 HW version ESP32-D0WD The device is recognized by iobroker, but the connection is offline every 30 to 60 minutes. After a few minutes it is online again, but the adapter (zigbee.iobroker) in the iobroker remains yellow. Only after restarting the adapter will it turn green again.
1. You mean socket connection to Zigbee module, right? 2. How about uptime of the gateway? Does is drops to 0 after connection goes offline?
- Yes, i mean socket Connection to Zigbee module
- Since I have reinstalled the old firmware, I cannot say anything for sure about it
from xzg.
It can be caused by two reasons: hang up Zigbee module or reboot ESP32. That's why we need to know about uptime.
from xzg.
Okay, then I'll update the second Zigbee adapter to the new version and see what happens. I'll report back.
from xzg.
I hope this helps a little. After 47 minutes, the Zigbee adapter lost its connection to the iobroker. The adapter (ESP32) then restarted and the connection times started again at zero. The connection to the iobroker is not established automatically. I cannot provide the raw data from the debug console as this is deleted when the adapter is restarted.
Another note: Since the Zigbee adapter did not work at the beginning after the web update, I installed the firmware via USB. Then the Zigbee adapter finally established the connection to the iobroker (green digit).
My File : configHw.json
{
"board": "WT32-ETH01",
"addr": 1,
"pwrPin": 16,
"mdcPin": 23,
"mdiPin": 18,
"phyType": 0,
"clkMode": 0,
"pwrAltPin": -1,
"btnPin": -1,
"btnPlr": 0,
"uartSelPin": -1,
"uartSelPlr": 0,
"ledModePin": -1,
"ledModePlr": 0,
"ledPwrPin": -1,
"ledPwrPlr": 0,
"zbTxPin": 17,
"zbRxPin": 5,
"zbRstPin": 33,
"zbBslPin": 32
}
from xzg.
I left the adapter running last night and could see that the ESP32 restarted after about 45 minutes. This morning I started the adapter again and after about 45 minutes the same thing happened again, the ESP32 restarted but the connection to the iobroker was not established automatically. A restart must be performed in iobroker. Here is the current information from the debug console.
58] -> fe 00 27 00 27
[29667] <- fe 12 67 00 00 43 2c d1 26 00 4b 12 00 00 00 07 09 02 90 a0 90 a0 b8
[29670] -> fe 04 25 05 00 00 00 00 24
[29671] -> fe 04 25 05 00 00 00 00 24
[29675] <- fe 12 67 00 00 43 2c d1 26 00 4b 12 00 00 00 07 09 02 90 a0 90 a0 b8
[29680] <- fe 01 65 05 00 61 fe 0b 45 85 00 00 00 00 00 05 05 04 03 02 01 cf fe 01 65 05 00 61
[29684] -> fe 09 24 00 06 09 01 05 00 00 00 00 00 26
[29685] -> fe 09 24 00 06 09 01 05 00 00 00 00 00 26
[29689] <- fe 0b 45 85 00 00 00 00 00 05 05 04 03 02 01 cf
[29694] <- fe 01 64 00 00 65 fe 01 64 00 b8 dd
[29696] -> fe 09 24 00 08 04 01 05 00 00 00 00 00 25
[29697] -> fe 09 24 00 08 04 01 05 00 00 00 00 00 25
[29704] <- fe 01 64 00 00 65 fe 01 64 00 b8 dd
[29708] -> fe 09 24 00 0a 04 01 05 00 00 00 00 00 27
[29709] -> fe 09 24 00 0a 04 01 05 00 00 00 00 00 27
[29715] <- fe 01 64 00 00 65 fe 01 64 00 b8 dd
[29719] -> fe 11 24 00 0b 04 01 00 04 00 00 02 01 05 0a 00 02 00 05 02 05 33
[29720] -> fe 11 24 00 0b 04 01 00 04 00 00 02 01 05 0a 00 02 00 05 02 05 33
[29729] <- fe 01 64 00 00 65 fe 01 64 00 b8 dd
[29732] -> fe 09 24 00 6e 04 01 05 00 00 00 00 00 43
[29733] -> fe 09 24 00 6e 04 01 05 00 00 00 00 00 43
[29739] <- fe 01 64 00 00 65
[29743] -> fe 09 24 00 0c 5e c0 05 00 00 00 00 00 ba
[29744] -> fe 09 24 00 0c 5e c0 05 00 00 00 00 00 ba
[29747] <- fe 01 64 00 b8 dd
[29751] <- fe 01 64 00 00 65 fe 01 64 00 b8 dd
[39767] | Connected client 5 from 192.168.1.75
[39768] -> ef
[40768] -> fe 00 21 01 20
[40775] <- fe 02 61 01 59 06 3d
[40778] -> fe 00 21 02 23
[40786] <- fe 0a 61 02 02 01 02 07 01 2a 8d 34 01 00 fc
[40790] -> fe 02 21 13 82 00 b2
[40802] <- fe 02 61 13 18 00 68
[40806] -> fe 04 21 1c 82 00 00 00 bb
[40828] <- fe 1a 61 1c 00 18 00 ee f4 94 8d 43 62 64 3e a9 1a 98 01 d6 2a e4 77 ee f4 94 89 13 00 00 56
[40831] -> fe 02 21 13 60 00 50
[40838] <- fe 02 61 13 01 00 71
[40841] -> fe 04 21 1c 60 00 00 00 59
[40850] <- fe 03 61 1c 00 01 55 2a
[40853] -> fe 02 21 13 21 00 11
[40862] <- fe 02 61 13 74 00 04
[40865] -> fe 04 21 1c 21 00 00 00 18
[40889] <- fe 76 61 1c 00 74 29 05 02 65 0f 65 00 1e 00 00 00 01 05 01 8f 00 07 00 02 0d 02 00 00 00 19 00 00 00 00 00 00 00 00 00 00 00 90 19 08 00 00 00 00 02 0f 0f 04 00 01 00 00 00 01 00 00 00 00 00 12 4b 00 21 9f b6 32 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0f 05 00 01 3c 0a 01 00 00 00 02 00 00 00 02
[40892] -> fe 02 21 13 62 00 52
[40900] <- fe 02 61 13 10 00 60
[40903] -> fe 04 21 1c 62 00 00 00 5b
[40913] <- fe 12 61 1c 00 10 01 03 05 07 09 0b 0d 0f 00 02 04 06 08 0a 0c 0d 7c
[40918] -> fe 02 21 13 3a 00 0a
[40927] <- fe 02 61 13 11 00 61
[40930] -> fe 04 21 1c 3a 00 00 00 03
[40944] <- fe 13 61 1c 00 11 00 01 03 05 07 09 0b 0d 0f 00 02 04 06 08 0a 0c 0d 7c
[40946] -> fe 02 21 13 3b 00 0b
[40955] <- fe 02 61 13 11 00 61
[40958] -> fe 04 21 1c 3b 00 00 00 02
[40972] <- fe 13 61 1c 00 11 00 01 03 05 07 09 0b 0d 0f 00 02 04 06 08 0a 0c 0d 7c
[40976] -> fe 00 27 00 27
[40985] <- fe 12 67 00 00 43 2c d1 26 00 4b 12 00 00 00 07 09 02 90 a0 90 a0 b8
[40988] -> fe 04 25 05 00 00 00 00 24
[40996] <- fe 01 65 05 00 61
[41001] <- fe 11 45 85 00 00 00 00 00 0b 0c 6e 0b 0a 08 06 05 04 03 02 01 b6
[41004] -> fe 0b 24 00 0d 04 01 05 00 00 00 01 19 00 00 3a
[41013] <- fe 01 64 00 00 65
[41017] -> fe 09 24 00 2f 04 01 05 00 00 00 00 00 02
[41024] <- fe 01 64 00 00 65
[41027] -> fe 09 24 00 f2 e0 a1 05 00 00 00 00 00 9b
[41034] <- fe 01 64 00 00 65
[41037] -> fe 03 25 4a f2 84 0b 11
[41045] <- fe 13 65 4a 00 84 0b 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b3
[644467] | Connected client 1 from 192.168.1.75
[644619] -> ef
[645641] -> fe 00 21 01 20
[645644] <- fe 02 61 01 59 06 3d
[645649] -> fe 00 21 02 23
[645653] <- fe 0a 61 02 02 01 02 07 01 2a 8d 34 01 00 fc
[645659] -> fe 02 21 13 82 00 b2
[645668] <- fe 02 61 13 18 00 68
[645671] -> fe 04 21 1c 82 00 00 00 bb
[645690] <- fe 1a 61 1c 00 18 00 ee f4 94 8d 43 62 64 3e a9 1a 98 01 d6 2a e4 77 ee f4 94 89 13 00 00 56
[645694] -> fe 02 21 13 60 00 50
[645699] <- fe 02 61 13 01 00 71
[645704] -> fe 04 21 1c 60 00 00 00 59
[645709] <- fe 03 61 1c 00 01 55 2a
[645715] -> fe 02 21 13 21 00 11
[645721] <- fe 02 61 13 74 00 04
[645725] -> fe 04 21 1c 21 00 00 00 18
[645746] <- fe 76 61 1c 00 74 29 05 02 65 0f 65 00 1e 00 00 00 01 05 01 8f 00 07 00 02 0d 02 00 00 00 19 00 00 00 00 00 00 00 00 00 00 00 90 19 08 00 00 00 00 02 0f 0f 04 00 01 00 00 00 01 00 00 00 00 00 12 4b 00 21 9f b6 32 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0f 05 00 01 3c 0a 01 00 00 00 02 00 00 00 02
[645752] -> fe 02 21 13 62 00 52
[645756] <- fe 02 61 13 10 00 60
[645759] -> fe 04 21 1c 62 00 00 00 5b
[645766] <- fe 12 61 1c 00 10 01 03 05 07 09 0b 0d 0f 00 02 04 06 08 0a 0c 0d 7c
[645769] -> fe 02 21 13 3a 00 0a
[645775] <- fe 02 61 13 11 00 61
[645778] -> fe 04 21 1c 3a 00 00 00 03
[645788] <- fe 13 61 1c 00 11 00 01 03 05 07 09 0b 0d 0f 00 02 04 06 08 0a 0c 0d 7c
[645791] -> fe 02 21 13 3b 00 0b
[645797] <- fe 02 61 13 11 00 61
[645801] -> fe 04 21 1c 3b 00 00 00 02
[645810] <- fe 13 61 1c 00 11 00 01 03 05 07 09 0b 0d 0f 00 02 04 06 08 0a 0c 0d 7c
[645817] -> fe 00 27 00 27
[645824] <- fe 12 67 00 00 43 2c d1 26 00 4b 12 00 00 00 07 09 02 90 a0 90 a0 b8
[645828] -> fe 04 25 05 00 00 00 00 24
[645832] <- fe 01 65 05 00 61
[645834] <- fe 14 45 85 00 00 00 00 00 0e f2 2f 0d 0c 6e 0b 0a 08 06 05 04 03 02 01 66
[645839] -> fe 03 25 4a f2 84 0b 11
[645844] <- fe 13 65 4a 00 84 0b 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b3
[645848] -> fe 04 25 05 00 00 00 00 24
[645852] <- fe 01 65 05 00 61
[645854] <- fe 14 45 85 00 00 00 00 00 0e f2 2f 0d 0c 6e 0b 0a 08 06 05 04 03 02 01 66
[645857] -> fe 00 27 00 27
[645864] <- fe 12 67 00 00 43 2c d1 26 00 4b 12 00 00 00 07 09 02 90 a0 90 a0 b8
[645868] -> fe 05 25 04 00 00 00 00 f2 d6
[645873] <- fe 01 65 04 00 60
[645875] <- fe 0e 45 84 00 00 00 00 00 08 f2 e0 a1 05 00 00 00 00 71
[645878] -> fe 05 25 04 00 00 00 00 2f 0b
[645882] <- fe 01 65 04 00 60
[645884] <- fe 0e 45 84 00 00 00 00 00 08 2f 04 01 05 00 00 00 00 e8
[645887] -> fe 05 25 04 00 00 00 00 0d 29
[645891] <- fe 01 65 04 00 60
[645893] <- fe 10 45 84 00 00 00 00 00 0a 0d 04 01 05 00 00 01 19 00 00 ce
[645896] -> fe 05 25 04 00 00 00 00 0c 28
[645900] <- fe 01 65 04 00 60
[645902] <- fe 0e 45 84 00 00 00 00 00 08 0c 5e c0 05 00 00 00 00 50
[645905] -> fe 05 25 04 00 00 00 00 6e 4a
[645909] <- fe 01 65 04 00 60
[645911] <- fe 0e 45 84 00 00 00 00 00 08 6e 04 01 05 00 00 00 00 a9
[645914] -> fe 05 25 04 00 00 00 00 0b 2f
[645918] <- fe 01 65 04 00 60
[645921] <- fe 16 45 84 00 00 00 00 00 10 0b 04 01 00 04 00 02 01 05 0a 00 02 00 05 02 05 c1
[645924] -> fe 05 25 04 00 00 00 00 0a 2e
[645928] <- fe 01 65 04 00 60
[645930] <- fe 0e 45 84 00 00 00 00 00 08 0a 04 01 05 00 00 00 00 cd
[645933] -> fe 05 25 04 00 00 00 00 08 2c
[645937] <- fe 01 65 04 00 60
[645939] <- fe 0e 45 84 00 00 00 00 00 08 08 04 01 05 00 00 00 00 cf
[645942] -> fe 05 25 04 00 00 00 00 06 22
[645946] <- fe 01 65 04 00 60
[645948] <- fe 0e 45 84 00 00 00 00 00 08 06 09 01 05 00 00 00 00 cc
[645951] -> fe 05 25 04 00 00 00 00 05 21
[645957] <- fe 01 65 04 00 60 fe 0e 45 84 00 00 00 00 00 08 05 08 01 05 00 00 00 00 ce
[645961] -> fe 05 25 04 00 00 00 00 04 20
[645965] <- fe 01 65 04 00 60
[645967] <- fe 0e 45 84 00 00 00 00 00 08 04 07 01 05 00 00 00 00 c0
[645970] -> fe 05 25 04 00 00 00 00 03 27
[645974] <- fe 01 65 04 00 60
[645976] <- fe 0e 45 84 00 00 00 00 00 08 03 04 01 05 00 00 00 00 c4
[645981] -> fe 05 25 04 00 00 00 00 02 26
[645985] <- fe 01 65 04 00 60
[645987] <- fe 0e 45 84 00 00 00 00 00 08 02 01 01 05 00 00 00 00 c0
[645992] -> fe 05 25 04 00 00 00 00 01 25
[645996] <- fe 01 65 04 00 60
[645998] <- fe 0e 45 84 00 00 00 00 00 08 01 04 01 05 00 00 00 00 c6
[646004] -> fe 00 25 50 75
[646009] <- fe 18 65 50 00 00 09 90 19 00 00 00 12 4b 00 21 9f b6 32 00 00 00 00 00 00 00 00 19 d7
[646028] -> fe 02 21 0f 00 00 2c
[646031] <- fe 01 61 0f 00 6f
from xzg.
But you uptime doesn't drops to zero, it is only goes up.
How did you detect that ESP32 restarted?
It looks like Zigbee chip hangups. What Zigbee chip are you using? What firmware version?
from xzg.
But your operating time doesn't go down to zero, it just goes up.
How did you detect that ESP32 was restarted?
The Device operating time counted from zero again.
It looks like the Zigbee chip is stuck. What Zigbee chip are you using?
That's an ebyte chip.
What firmware version?
FW revision 20221226
I have no problems with firmware version 06.10.
from xzg.
The Device operating time counted from zero again.
But in logs that you provide time only goes up. So I thought that way.
That's an ebyte chip.
OK.
FW revision 20221226
I have no problems with firmware version 06.10.
OK. But we need to check all first.
Have you tried to use latest version of XZG ?
from xzg.
I installed version 20240524 on the ESP and 20221226 on the Zigbee module. I use the same Zigbee firmware on my active adapter with FW06.10.
I have the RAW data here until shortly before the crash.
[1134] | [ZB] Chip: CC2652P2_other
[1134] | [ZB] IEEE: 00:12:4B:00:26:D1:2C:43
[1145] | [ZB] Flash size: 352 KB
[4243] | [ZB] fw: 20221226
[6672] | Local time: Fri May 24 19:03:32 2024
[47221] | Connected client 1 from 192.168.1.75
[47346] -> ef
[48349] -> fe 00 21 01 20
[48353] <- fe 02 61 01 59 06 3d
[48358] -> fe 00 21 02 23
[48361] <- fe 0a 61 02 02 01 02 07 01 2a 8d 34 01 00 fc
[48366] -> fe 02 21 13 82 00 b2
[48372] <- fe 02 61 13 18 00 68
[48376] -> fe 04 21 1c 82 00 00 00 bb
[48387] <- fe 1a 61 1c 00 18 00 ee f4 94 8d 43 62 64 3e a9 1a 98 01 d6 2a e4 77 ee f4 94 89 13 00 00 56
[48392] -> fe 02 21 13 60 00 50
[48400] <- fe 02 61 13 01 00 71
[48404] -> fe 04 21 1c 60 00 00 00 59
[48416] <- fe 03 61 1c 00 01 55 2a
[48420] -> fe 02 21 13 21 00 11
[48425] <- fe 02 61 13 74 00 04
[48429] -> fe 04 21 1c 21 00 00 00 18
[48445] <- fe 76 61 1c 00 74 89 05 02 65 0f 65 00 1e 00 00 00 01 05 01 8f 00 07 00 02 0d 02 00 00 00 19 00 00 00 00 00 00 00 00 00 00 00 90 19 08 00 00 00 00 02 0f 0f 04 00 01 00 00 00 01 00 00 00 00 00 12 4b 00 21 9f b6 32 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0f 05 00 01 3c 0a 01 00 00 00 05 00 00 00 a5
[48451] -> fe 02 21 13 62 00 52
[48458] <- fe 02 61 13 10 00 60
[48463] -> fe 04 21 1c 62 00 00 00 5b
[48476] <- fe 12 61 1c 00 10 01 03 05 07 09 0b 0d 0f 00 02 04 06 08 0a 0c 0d 7c
[48481] -> fe 02 21 13 3a 00 0a
[48489] <- fe 02 61 13 11 00 61
[48493] -> fe 04 21 1c 3a 00 00 00 03
[48508] <- fe 13 61 1c 00 11 00 01 03 05 07 09 0b 0d 0f 00 02 04 06 08 0a 0c 0d 7c
[48512] -> fe 02 21 13 3b 00 0b
[48520] <- fe 02 61 13 11 00 61
[48523] -> fe 04 21 1c 3b 00 00 00 02
[48575] <- fe 13 61 1c 00 11 00 01 03 05 07 09 0b 0d 0f 00 02 04 06 08 0a 0c 0d 7c
[48589] -> fe 00 27 00 27
[48603] <- fe 0e 67 00 00 43 2c d1 26 00 4b 12 00 fe ff 07 00 00 ae
[48607] -> fe 02 25 40 64 00 03
[51995] <- fe 01 65 40 00 24
[51997] <- fe 01 45 c0 09 8d fe 03 4f 80 0d 00 04 c5
[52001] -> fe 04 25 05 00 00 00 00 24
[52005] <- fe 01 65 05 00 61
[52008] <- fe 06 45 85 00 00 00 00 00 00 c6
[52011] -> fe 09 24 00 01 04 01 05 00 00 00 00 00 2c
[52015] <- fe 01 64 00 00 65
[52019] -> fe 09 24 00 02 01 01 05 00 00 00 00 00 2a
[52022] <- fe 01 64 00 00 65
[52027] -> fe 09 24 00 03 04 01 05 00 00 00 00 00 2e
[52031] <- fe 01 64 00 00 65
[52035] -> fe 09 24 00 04 07 01 05 00 00 00 00 00 2a
[52038] <- fe 01 64 00 00 65
[52042] -> fe 09 24 00 05 08 01 05 00 00 00 00 00 24
[52045] <- fe 01 64 00 00 65
[52050] -> fe 09 24 00 06 09 01 05 00 00 00 00 00 26
[52054] <- fe 01 64 00 00 65
[52058] -> fe 09 24 00 08 04 01 05 00 00 00 00 00 25
[52061] <- fe 01 64 00 00 65
[52065] -> fe 09 24 00 0a 04 01 05 00 00 00 00 00 27
[52068] <- fe 01 64 00 00 65
[52072] -> fe 11 24 00 0b 04 01 00 04 00 00 02 01 05 0a 00 02 00 05 02 05 33
[52076] <- fe 01 64 00 00 65
[52081] -> fe 09 24 00 6e 04 01 05 00 00 00 00 00 43
[52085] <- fe 01 64 00 00 65
[52089] -> fe 09 24 00 0c 5e c0 05 00 00 00 00 00 ba
[52093] <- fe 01 64 00 00 65
[52097] -> fe 0b 24 00 0d 04 01 05 00 00 00 01 19 00 00 3a
[52107] <- fe 01 64 00 00 65
[52110] -> fe 09 24 00 2f 04 01 05 00 00 00 00 00 02
[52114] <- fe 01 64 00 00 65
[52119] -> fe 09 24 00 f2 e0 a1 05 00 00 00 00 00 9b
[52123] <- fe 01 64 00 00 65
[52127] -> fe 03 25 4a f2 84 0b 11
[52132] <- fe 13 65 4a 00 84 0b 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b3
[52136] -> fe 04 25 05 00 00 00 00 24
[52140] <- fe 01 65 05 00 61
[52143] <- fe 14 45 85 00 00 00 00 00 0e f2 2f 0d 0c 6e 0b 0a 08 06 05 04 03 02 01 66
[52147] -> fe 00 27 00 27
[52157] <- fe 12 67 00 00 43 2c d1 26 00 4b 12 00 00 00 07 09 02 90 a0 90 a0 b8
[52161] -> fe 05 25 04 00 00 00 00 f2 d6
[52165] <- fe 01 65 04 00 60
[52168] <- fe 0e 45 84 00 00 00 00 00 08 f2 e0 a1 05 00 00 00 00 71
[52171] -> fe 05 25 04 00 00 00 00 2f 0b
[52176] <- fe 01 65 04 00 60
[52179] <- fe 0e 45 84 00 00 00 00 00 08 2f 04 01 05 00 00 00 00 e8
[52182] -> fe 05 25 04 00 00 00 00 0d 29
[52187] <- fe 01 65 04 00 60
[52190] <- fe 10 45 84 00 00 00 00 00 0a 0d 04 01 05 00 00 01 19 00 00 ce
[52194] -> fe 05 25 04 00 00 00 00 0c 28
[52195] <- fe 03 4f 80 08 02 00 c6
[52198] <- fe 01 65 04 00 60
[52202] <- fe 0e 45 84 00 00 00 00 00 08 0c 5e c0 05 00 00 00 00 50
[52205] -> fe 05 25 04 00 00 00 00 6e 4a
[52210] <- fe 01 65 04 00 60
[52213] <- fe 0e 45 84 00 00 00 00 00 08 6e 04 01 05 00 00 00 00 a9
[52216] -> fe 05 25 04 00 00 00 00 0b 2f
[52220] <- fe 01 65 04 00 60
[52223] <- fe 16 45 84 00 00 00 00 00 10 0b 04 01 00 04 00 02 01 05 0a 00 02 00 05 02 05 c1
[52227] -> fe 05 25 04 00 00 00 00 0a 2e
[52231] <- fe 01 65 04 00 60
[52234] <- fe 0e 45 84 00 00 00 00 00 08 0a 04 01 05 00 00 00 00 cd
[52237] -> fe 05 25 04 00 00 00 00 08 2c
[52242] <- fe 01 65 04 00 60
[52245] <- fe 0e 45 84 00 00 00 00 00 08 08 04 01 05 00 00 00 00 cf
[52248] -> fe 05 25 04 00 00 00 00 06 22
[52252] <- fe 01 65 04 00 60
[52255] <- fe 0e 45 84 00 00 00 00 00 08 06 09 01 05 00 00 00 00 cc
[52258] -> fe 05 25 04 00 00 00 00 05 21
[52263] <- fe 01 65 04 00 60
[52266] <- fe 0e 45 84 00 00 00 00 00 08 05 08 01 05 00 00 00 00 ce
[52286] -> fe 05 25 04 00 00 00 00 04 20
[52290] <- fe 01 65 04 00 60
[52293] <- fe 0e 45 84 00 00 00 00 00 08 04 07 01 05 00 00 00 00 c0
[52296] -> fe 05 25 04 00 00 00 00 03 27
[52300] <- fe 01 65 04 00 60
[52303] <- fe 0e 45 84 00 00 00 00 00 08 03 04 01 05 00 00 00 00 c4
[52307] -> fe 05 25 04 00 00 00 00 02 26
[52311] <- fe 01 65 04 00 60
[52314] <- fe 0e 45 84 00 00 00 00 00 08 02 01 01 05 00 00 00 00 c0
[52317] -> fe 05 25 04 00 00 00 00 01 25
[52321] <- fe 01 65 04 00 60
[52324] <- fe 0e 45 84 00 00 00 00 00 08 01 04 01 05 00 00 00 00 c6
[52333] -> fe 00 25 50 75
[52338] <- fe 18 65 50 00 00 09 90 19 00 00 00 12 4b 00 21 9f b6 32 00 00 00 00 00 00 00 00 19 d7
[52354] -> fe 02 21 0f 00 00 2c
[52357] <- fe 01 61 0f 00 6f
Here is the data after the restart.
[1134] | [ZB] Chip: CC2652P2_other
[1134] | [ZB] IEEE: 00:12:4B:00:26:D1:2C:43
[1145] | [ZB] Flash size: 352 KB
[4137] | [ZB] fw: 20221226
[7196] | Local time: Fri May 24 19:44:46 2024
[15205] | Connected client 1 from 192.168.1.75
[15207] -> ef
[16208] -> fe 00 21 01 20
[16212] <- fe 02 61 01 59 06 3d
[16215] -> fe 00 21 02 23
[16219] <- fe 0a 61 02 02 01 02 07 01 2a 8d 34 01 00 fc
[16223] -> fe 02 21 13 82 00 b2
[16229] <- fe 02 61 13 18 00 68
[16232] -> fe 04 21 1c 82 00 00 00 bb
[16244] <- fe 1a 61 1c 00 18 00 ee f4 94 8d 43 62 64 3e a9 1a 98 01 d6 2a e4 77 ee f4 94 89 13 00 00 56
[16248] -> fe 02 21 13 60 00 50
[16255] <- fe 02 61 13 01 00 71
[16259] -> fe 04 21 1c 60 00 00 00 59
[16272] <- fe 03 61 1c 00 01 55 2a
[16276] -> fe 02 21 13 21 00 11
[16280] <- fe 02 61 13 74 00 04
[16284] -> fe 04 21 1c 21 00 00 00 18
[16301] <- fe 76 61 1c 00 74 8a 05 02 65 0f 65 00 1e 00 00 00 01 05 01 8f 00 07 00 02 0d 02 00 00 00 19 00 00 00 00 00 00 00 00 00 00 00 90 19 08 00 00 00 00 02 0f 0f 04 00 01 00 00 00 01 00 00 00 00 00 12 4b 00 21 9f b6 32 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0f 05 00 01 3c 0a 01 00 00 00 05 00 00 00 a6
[16306] -> fe 02 21 13 62 00 52
[16314] <- fe 02 61 13 10 00 60
[16318] -> fe 04 21 1c 62 00 00 00 5b
[16332] <- fe 12 61 1c 00 10 01 03 05 07 09 0b 0d 0f 00 02 04 06 08 0a 0c 0d 7c
[16337] -> fe 02 21 13 3a 00 0a
[16346] <- fe 02 61 13 11 00 61
[16350] -> fe 04 21 1c 3a 00 00 00 03
[16366] <- fe 13 61 1c 00 11 00 01 03 05 07 09 0b 0d 0f 00 02 04 06 08 0a 0c 0d 7c
[16370] -> fe 02 21 13 3b 00 0b
[16379] <- fe 02 61 13 11 00 61
[16383] -> fe 04 21 1c 3b 00 00 00 02
[16408] <- fe 13 61 1c 00 11 00 01 03 05 07 09 0b 0d 0f 00 02 04 06 08 0a 0c 0d 7c
[16414] -> fe 00 27 00 27
[16423] <- fe 0e 67 00 00 43 2c d1 26 00 4b 12 00 fe ff 07 00 00 ae
[16427] -> fe 02 25 40 64 00 03
[20049] <- fe 01 65 40 00 24
[20051] <- fe 01 45 c0 09 8d fe 03 4f 80 0d 00 04 c5
[20055] -> fe 04 25 05 00 00 00 00 24
[20059] <- fe 01 65 05 00 61
[20062] <- fe 06 45 85 00 00 00 00 00 00 c6
[20065] -> fe 09 24 00 01 04 01 05 00 00 00 00 00 2c
[20069] <- fe 01 64 00 00 65
[20072] -> fe 09 24 00 02 01 01 05 00 00 00 00 00 2a
[20076] <- fe 01 64 00 00 65
[20080] -> fe 09 24 00 03 04 01 05 00 00 00 00 00 2e
[20083] <- fe 01 64 00 00 65
[20087] -> fe 09 24 00 04 07 01 05 00 00 00 00 00 2a
[20090] <- fe 01 64 00 00 65
[20094] -> fe 09 24 00 05 08 01 05 00 00 00 00 00 24
[20097] <- fe 01 64 00 00 65
[20101] -> fe 09 24 00 06 09 01 05 00 00 00 00 00 26
[20104] <- fe 01 64 00 00 65
[20108] -> fe 09 24 00 08 04 01 05 00 00 00 00 00 25
[20111] <- fe 01 64 00 00 65
[20115] -> fe 09 24 00 0a 04 01 05 00 00 00 00 00 27
[20119] <- fe 01 64 00 00 65
[20123] -> fe 11 24 00 0b 04 01 00 04 00 00 02 01 05 0a 00 02 00 05 02 05 33
[20127] <- fe 01 64 00 00 65
[20131] -> fe 09 24 00 6e 04 01 05 00 00 00 00 00 43
[20134] <- fe 01 64 00 00 65
[20138] -> fe 09 24 00 0c 5e c0 05 00 00 00 00 00 ba
[20142] <- fe 01 64 00 00 65
[20146] -> fe 0b 24 00 0d 04 01 05 00 00 00 01 19 00 00 3a
[20161] <- fe 01 64 00 00 65
[20165] -> fe 09 24 00 2f 04 01 05 00 00 00 00 00 02
[20168] <- fe 01 64 00 00 65
[20172] -> fe 09 24 00 f2 e0 a1 05 00 00 00 00 00 9b
[20176] <- fe 01 64 00 00 65
[20180] -> fe 03 25 4a f2 84 0b 11
[20185] <- fe 13 65 4a 00 84 0b 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b3
[20188] -> fe 04 25 05 00 00 00 00 24
[20192] <- fe 01 65 05 00 61
[20195] <- fe 14 45 85 00 00 00 00 00 0e f2 2f 0d 0c 6e 0b 0a 08 06 05 04 03 02 01 66
[20199] -> fe 00 27 00 27
[20209] <- fe 12 67 00 00 43 2c d1 26 00 4b 12 00 00 00 07 09 02 90 a0 90 a0 b8
[20213] -> fe 05 25 04 00 00 00 00 f2 d6
[20217] <- fe 01 65 04 00 60
[20220] <- fe 0e 45 84 00 00 00 00 00 08 f2 e0 a1 05 00 00 00 00 71
[20223] -> fe 05 25 04 00 00 00 00 2f 0b
[20227] <- fe 01 65 04 00 60
[20230] <- fe 0e 45 84 00 00 00 00 00 08 2f 04 01 05 00 00 00 00 e8
[20233] -> fe 05 25 04 00 00 00 00 0d 29
[20238] <- fe 01 65 04 00 60
[20241] <- fe 10 45 84 00 00 00 00 00 0a 0d 04 01 05 00 00 01 19 00 00 ce
[20245] -> fe 05 25 04 00 00 00 00 0c 28
[20248] <- fe 03 4f 80 08 02 00 c6
[20251] <- fe 01 65 04 00 60 fe 0e 45 84 00 00 00 00 00 08 0c 5e c0 05 00 00 00 00 50
[20256] -> fe 05 25 04 00 00 00 00 6e 4a
[20260] <- fe 01 65 04 00 60
[20263] <- fe 0e 45 84 00 00 00 00 00 08 6e 04 01 05 00 00 00 00 a9
[20268] -> fe 05 25 04 00 00 00 00 0b 2f
[20272] <- fe 01 65 04 00 60
[20275] <- fe 16 45 84 00 00 00 00 00 10 0b 04 01 00 04 00 02 01 05 0a 00 02 00 05 02 05 c1
[20278] -> fe 05 25 04 00 00 00 00 0a 2e
[20282] <- fe 01 65 04 00 60
[20285] <- fe 0e 45 84 00 00 00 00 00 08 0a 04 01 05 00 00 00 00 cd
[20288] -> fe 05 25 04 00 00 00 00 08 2c
[20292] <- fe 01 65 04 00 60
[20295] <- fe 0e 45 84 00 00 00 00 00 08 08 04 01 05 00 00 00 00 cf
[20298] -> fe 05 25 04 00 00 00 00 06 22
[20303] <- fe 01 65 04 00 60
[20306] <- fe 0e 45 84 00 00 00 00 00 08 06 09 01 05 00 00 00 00 cc
[20309] -> fe 05 25 04 00 00 00 00 05 21
[20314] <- fe 01 65 04 00 60
[20317] <- fe 0e 45 84 00 00 00 00 00 08 05 08 01 05 00 00 00 00 ce
[20320] -> fe 05 25 04 00 00 00 00 04 20
[20325] <- fe 01 65 04 00 60
[20328] <- fe 0e 45 84 00 00 00 00 00 08 04 07 01 05 00 00 00 00 c0
[20331] -> fe 05 25 04 00 00 00 00 03 27
[20336] <- fe 01 65 04 00 60
[20339] <- fe 0e 45 84 00 00 00 00 00 08 03 04 01 05 00 00 00 00 c4
[20343] -> fe 05 25 04 00 00 00 00 02 26
[20347] <- fe 01 65 04 00 60
[20350] <- fe 0e 45 84 00 00 00 00 00 08 02 01 01 05 00 00 00 00 c0
[20354] -> fe 05 25 04 00 00 00 00 01 25
[20358] <- fe 01 65 04 00 60
[20361] <- fe 0e 45 84 00 00 00 00 00 08 01 04 01 05 00 00 00 00 c6
[20369] -> fe 02 21 0f 00 00 2c
[20373] <- fe 01 61 0f 00 6f
from xzg.
Do you keep your tab with web UI open continuously?
from xzg.
Yes, the tab is permanently open.
When the failure occurs, 5 devices are shown as connected. But since it is a test environment, it can actually only be one device. Then in iobroker we noticed that the RAM usage was no longer 130 MB but had gone up to over 600 MB.
from xzg.
It looks like some problems with iobroker.
It's the first report about the socket connections count is wrong.
from xzg.
I have no other ideas at the moment.
from xzg.
That's not a problem at the moment. My active Zigbee LAN adapter is currently still running on the old version.
from xzg.
Related Issues (20)
- Unable to build XZG firmware - src/web.cpp:23:10: fatal error: webh/html/PAGE_VPN.html.gz.h: No such file or directory HOT 2
- HTTP 502 on the General page of the Web interface when serving through reverse proxy HOT 2
- Connect Wifi to strongest AP
- SLZB-06M can't leave access point mode HOT 24
- Socket connection and MQTT need to be stoped while Zigbee flash HOT 15
- Hostname setting is ignored for WebUI HOT 1
- После установки прошивки 20240609 на шлюзы, программа ZigstarGW-MT перестала видеть шлюзы. Их у меня 5 шт. HOT 1
- tubeszb-efr32-mgm210-poe-2022 failed to load after flashing to XZG from ESPHome HOT 2
- Wireguard no longer connects after upgrade from FW revision 20240519 to 20240612 HOT 18
- Home Assistant - Update Notifications HOT 1
- SLZB-06 - No network, no ZIGBEE HOT 22
- The Delete-button in File Browser is to easy to misinterpret HOT 2
- Scan request failed or was not answered HOT 1
- Zigbee connected, but socket saying "No connection" HOT 1
- Export Zigbee traffic counters to MQTT
- Unexpected reboot of esp32 HOT 5
- Ita translate error HOT 10
- uzg-01 zigstar wireguard vpn client not working HOT 14
- Support for capturing traffic to/from a Zigbee device? HOT 2
- UZG-01 running 20240707 crashes (stalls) after 1-2 days HOT 14
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from xzg.