It looks like some regression on the current master branch when using Orange Pi Plus. The power of the 4 USB ports is not supplied, therefore I can't connect a keyboard to do any kind of setup. I rigged a serial console and got a debug log I'm attaching below.
Judging by the log all ohci/ehci usb controllers are properly setup, must be the missing gpio line that turns on power in DeviceTree.
Power is okay, but no devices detected.
U-Boot 2020.10 (Dec 05 2020 - 11:18:34 +0000) Allwinner Technology
CPU: Allwinner H3 (SUN8I 1680)
Model: Xunlong Orange Pi PC Plus
DRAM: 1 GiB
MMC: mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1
Loading Environment from FAT... Unable to use mmc 1:1... In: serial@1c28000
Out: serial@1c28000
Err: serial@1c28000
Net: No ethernet found.
starting USB...
No working controllers found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
166 bytes read in 6 ms (26.4 KiB/s)
1: LibreELEC
Retrieving file: /KERNEL
9521824 bytes read in 425 ms (21.4 MiB/s)
append: boot=UUID=0512-0153 disk=UUID=156e202a-4813-4e9a-8682-e8156497d52f console=ttyS0,115200
Retrieving file: /sun8i-h3-orangepi-pc-plus.dtb
23474 bytes read in 5 ms (4.5 MiB/s)
## Flattened Device Tree blob at 43000000
Booting using the fdt blob at 0x43000000
Loading Device Tree to 49ff7000, end 49fffbb1 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.9.11 (necromant@buildblade) (armv7ve-libreelec-linux-gnueabihf-gcc-10.2.0 (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.1) #1 SMP Sat Dec 5 11:24:49 UTC 2020
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Xunlong Orange Pi PC Plus
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 256 MiB at 0x60000000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000040000000-0x000000006fffffff]
[ 0.000000] HighMem [mem 0x0000000070000000-0x000000007fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
[ 0.000000] percpu: Embedded 15 pages/cpu s32588 r8192 d20660 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416
[ 0.000000] Kernel command line: boot=UUID=0512-0153 disk=UUID=156e202a-4813-4e9a-8682-e8156497d52f console=ttyS0,115200 root=/dev/ram0 rdinit=/init
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 757392K/1048576K available (9216K kernel code, 472K rwdata, 2444K rodata, 5120K init, 276K bss, 29040K reserved, 262144K cma-reserved, 262132K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000016] Switching to timer-based delay loop, resolution 41ns
[ 0.000176] Console: colour dummy device 80x30
[ 0.000219] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000230] pid_max: default: 32768 minimum: 301
[ 0.000369] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.000384] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.001247] CPU: Testing write buffer coherency: ok
[ 0.001534] /cpus/cpu@0 missing clock-frequency property
[ 0.001555] /cpus/cpu@1 missing clock-frequency property
[ 0.001573] /cpus/cpu@2 missing clock-frequency property
[ 0.001591] /cpus/cpu@3 missing clock-frequency property
[ 0.001601] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.002097] Setting up static identity map for 0x40100000 - 0x40100060
[ 0.002210] rcu: Hierarchical SRCU implementation.
[ 0.002679] smp: Bringing up secondary CPUs ...
[ 0.013341] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.024099] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.034804] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.034895] smp: Brought up 1 node, 4 CPUs
[ 0.034913] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 0.034918] CPU: All CPU(s) started in HYP mode.
[ 0.034923] CPU: Virtualization extensions available.
[ 0.035513] devtmpfs: initialized
[ 0.040026] random: get_random_u32 called from bucket_table_alloc+0x54/0x138 with crng_init=0
[ 0.040341] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.040563] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.040585] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.049101] pinctrl core: initialized pinctrl subsystem
[ 0.050240] NET: Registered protocol family 16
[ 0.051519] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.052350] thermal_sys: Registered thermal governor 'step_wise'
[ 0.052675] cpuidle: using governor ladder
[ 0.052706] cpuidle: using governor menu
[ 0.052869] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.052878] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.077318] SCSI subsystem initialized
[ 0.077815] usbcore: registered new interface driver usbfs
[ 0.077860] usbcore: registered new interface driver hub
[ 0.077915] usbcore: registered new device driver usb
[ 0.078113] mc: Linux media interface: v0.10
[ 0.078145] videodev: Linux video capture interface: v2.00
[ 0.078255] pps_core: LinuxPPS API ver. 1 registered
[ 0.078262] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 0.078279] PTP clock support registered
[ 0.078662] Advanced Linux Sound Architecture Driver Initialized.
[ 0.079453] clocksource: Switched to clocksource arch_sys_counter
[ 0.086665] NET: Registered protocol family 2
[ 0.087274] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.087304] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.087375] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.087488] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.087598] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.087656] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.087873] NET: Registered protocol family 1
[ 0.088331] RPC: Registered named UNIX socket transport module.
[ 0.088339] RPC: Registered udp transport module.
[ 0.088344] RPC: Registered tcp transport module.
[ 0.088349] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.103453] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 0.105135] Initialise system trusted keyrings
[ 0.105297] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.111338] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.112479] NFS: Registering the id_resolver key type
[ 0.112512] Key type id_resolver registered
[ 0.112518] Key type id_legacy registered
[ 0.112620] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.113301] Key type cifs.idmap registered
[ 0.113607] NET: Registered protocol family 38
[ 0.113618] Key type asymmetric registered
[ 0.113624] Asymmetric key parser 'x509' registered
[ 0.113629] Asymmetric key parser 'pkcs8' registered
[ 0.113679] bounce: pool size: 64 pages
[ 0.113726] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 0.113867] io scheduler mq-deadline registered
[ 0.113877] io scheduler kyber registered
[ 0.114663] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO
[ 0.118795] sun8i-h3-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 0.120599] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver
[ 0.166982] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[ 0.169329] sun8i-h3-pinctrl 1c20800.pinctrl: supply vcc-pa not found, using dummy regulator
[ 0.170201] printk: console [ttyS0] disabled
[ 0.170288] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 44, base_baud = 1500000) is a 16550A
[ 0.885110] printk: console [ttyS0] enabled
[ 0.904061] sun4i-drm display-engine: bound 1100000.mixer (ops 0xc0a5f9b0)
[ 0.911254] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops 0xc0a5c050)
[ 0.918957] sun8i-dw-hdmi 1ee0000.hdmi: supply hvcc not found, using dummy regulator
[ 0.928013] sun8i-dw-hdmi 1ee0000.hdmi: Detected HDMI TX controller v1.32a with HDCP (sun8i_dw_hdmi_phy)
[ 0.937812] sun8i-dw-hdmi 1ee0000.hdmi: registered DesignWare HDMI I2C bus driver
[ 0.945490] sun4i-drm display-engine: bound 1ee0000.hdmi (ops 0xc0a5ef84)
[ 0.952766] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0
[ 1.065519] random: fast init done
[ 1.385972] Console: switching to colour frame buffer device 240x67
[ 1.425561] sun4i-drm display-engine: [drm] fb0: sun4i-drmdrmfb frame buffer device
[ 1.443953] brd: module loaded
[ 1.447138] loop: module loaded
[ 1.469652] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 1.477515] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <[email protected]>. All Rights Reserved.
[ 1.487776] libphy: Fixed MDIO Bus: probed
[ 1.492645] tun: Universal TUN/TAP device driver, 1.6
[ 1.497885] CAN device driver interface
[ 1.502270] dwmac-sun8i 1c30000.ethernet: IRQ eth_wake_irq not found
[ 1.508629] dwmac-sun8i 1c30000.ethernet: IRQ eth_lpi not found
[ 1.514703] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
[ 1.520503] dwmac-sun8i 1c30000.ethernet: No regulator found
[ 1.526420] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported
[ 1.533674] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported
[ 1.540900] dwmac-sun8i 1c30000.ethernet: COE Type 2
[ 1.545870] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
[ 1.552660] dwmac-sun8i 1c30000.ethernet: Normal descriptors
[ 1.558316] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
[ 1.564482] libphy: stmmac: probed
[ 1.568840] dwmac-sun8i 1c30000.ethernet: Found internal PHY node
[ 1.575358] libphy: mdio_mux: probed
[ 1.578975] dwmac-sun8i 1c30000.ethernet: Switch mux to internal PHY
[ 1.585346] dwmac-sun8i 1c30000.ethernet: Powering internal PHY
[ 1.592839] libphy: mdio_mux: probed
[ 1.596995] usbcore: registered new interface driver r8152
[ 1.602531] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.609059] ehci-platform: EHCI generic platform driver
[ 1.614511] ehci-platform 1c1a000.usb: EHCI Host Controller
[ 1.620118] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1
[ 1.628291] ehci-platform 1c1a000.usb: irq 29, io mem 0x01c1a000
[ 1.659463] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
[ 1.665775] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[ 1.674055] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.681288] usb usb1: Product: EHCI Host Controller
[ 1.686166] usb usb1: Manufacturer: Linux 5.9.11 ehci_hcd
[ 1.691568] usb usb1: SerialNumber: 1c1a000.usb
[ 1.696658] hub 1-0:1.0: USB hub found
[ 1.700502] hub 1-0:1.0: 1 port detected
[ 1.705303] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.711536] ohci-platform: OHCI generic platform driver
[ 1.716945] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
[ 1.723582] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
[ 1.731584] ohci-platform 1c1a400.usb: irq 30, io mem 0x01c1a400
[ 1.803638] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.09
[ 1.811941] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.819158] usb usb2: Product: Generic Platform OHCI controller
[ 1.825087] usb usb2: Manufacturer: Linux 5.9.11 ohci_hcd
[ 1.830499] usb usb2: SerialNumber: 1c1a400.usb
[ 1.835577] hub 2-0:1.0: USB hub found
[ 1.839359] hub 2-0:1.0: 1 port detected
[ 1.844409] usbcore: registered new interface driver uas
[ 1.849822] usbcore: registered new interface driver usb-storage
[ 1.857337] sun6i-rtc 1f00000.rtc: registered as rtc0
[ 1.862442] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-01T00:00:04 UTC (4)
[ 1.870363] sun6i-rtc 1f00000.rtc: RTC enabled
[ 1.874936] i2c /dev entries driver
[ 1.878785] sun8i-h3-r-pinctrl 1f02c00.pinctrl: supply vcc-pl not found, using dummy regulator
[ 1.890304] IR NEC protocol handler initialized
[ 1.894831] IR RC5(x/sz) protocol handler initialized
[ 1.899898] IR RC6 protocol handler initialized
[ 1.904421] IR JVC protocol handler initialized
[ 1.908942] IR Sony protocol handler initialized
[ 1.913568] IR SANYO protocol handler initialized
[ 1.918264] IR Sharp protocol handler initialized
[ 1.922969] IR MCE Keyboard/mouse protocol handler initialized
[ 1.928791] IR XMP protocol handler initialized
[ 1.933321] ir_imon_decoder: IR iMON protocol handler initialized
[ 1.939402] IR RCMM protocol handler initialized
[ 1.944350] Registered IR keymap rc-empty
[ 1.948427] rc rc0: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0
[ 1.955324] rc rc0: lirc_dev: driver sunxi-ir registered at minor = 0, raw IR receiver, no transmitter
[ 1.964759] input: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0/input0
[ 1.972286] sunxi-ir 1f02000.ir: initialized sunXi IR driver
[ 1.978180] usbcore: registered new interface driver xbox_remote
[ 1.985333] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 1.994870] sun8i-h3-pinctrl 1c20800.pinctrl: supply vcc-pf not found, using dummy regulator
[ 2.004203] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[ 2.032038] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB
[ 2.039351] sun8i-h3-pinctrl 1c20800.pinctrl: supply vcc-pg not found, using dummy regulator
[ 2.072153] sunxi-mmc 1c10000.mmc: initialized, max. request size: 16384 KB
[ 2.079506] sun8i-h3-pinctrl 1c20800.pinctrl: supply vcc-pc not found, using dummy regulator
[ 2.096440] mmc0: host does not support reading read-only switch, assuming write-enable
[ 2.106800] mmc0: new high speed SDHC card at address a1ca
[ 2.113020] mmcblk0: mmc0:a1ca SU08G 7.40 GiB
[ 2.117072] sunxi-mmc 1c11000.mmc: initialized, max. request size: 16384 KB
[ 2.124217] mmc1: new high speed SDIO card at address 0001
[ 2.125528] hid: raw HID events driver (C) Jiri Kosina
[ 2.131834] mmcblk0: p1 p2
[ 2.135743] usbcore: registered new interface driver usbhid
[ 2.143430] usbhid: USB HID core driver
[ 2.149833] cedrus 1c0e000.video-codec: Device registered as /dev/video0
[ 2.160725] sun4i-codec 1c22c00.codec: Failed to register our card
[ 2.168561] Initializing XFRM netlink socket
[ 2.173397] NET: Registered protocol family 10
[ 2.178701] Segment Routing with IPv6
[ 2.182462] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.188981] NET: Registered protocol family 17
[ 2.193453] can: controller area network core (rev 20170425 abi 9)
[ 2.199704] NET: Registered protocol family 29
[ 2.204143] can: raw protocol (rev 20170425)
[ 2.208407] can: broadcast manager protocol (rev 20170425 t)
[ 2.214075] can: netlink gateway (rev 20190810) max_hops=1
[ 2.219765] Key type dns_resolver registered
[ 2.221488] mmc2: new DDR MMC card at address 0001
[ 2.224119] Registering SWP/SWPB emulation handler
[ 2.229691] mmcblk2: mmc2:0001 NCard 7.30 GiB
[ 2.233889] Loading compiled-in X.509 certificates
[ 2.238511] mmcblk2boot0: mmc2:0001 NCard partition 1 4.00 MiB
[ 2.249353] mmcblk2boot1: mmc2:0001 NCard partition 2 4.00 MiB
[ 2.254560] ehci-platform 1c1b000.usb: EHCI Host Controller
[ 2.257572] mmcblk2: p1
[ 2.260927] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 3
[ 2.271767] ehci-platform 1c1b000.usb: irq 31, io mem 0x01c1b000
[ 2.299473] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00
[ 2.305763] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[ 2.314043] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.321269] usb usb3: Product: EHCI Host Controller
[ 2.326141] usb usb3: Manufacturer: Linux 5.9.11 ehci_hcd
[ 2.331542] usb usb3: SerialNumber: 1c1b000.usb
[ 2.336648] hub 3-0:1.0: USB hub found
[ 2.340450] hub 3-0:1.0: 1 port detected
[ 2.345392] ehci-platform 1c1c000.usb: EHCI Host Controller
[ 2.351002] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 4
[ 2.359104] ehci-platform 1c1c000.usb: irq 33, io mem 0x01c1c000
[ 2.389452] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[ 2.395712] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[ 2.403982] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.411204] usb usb4: Product: EHCI Host Controller
[ 2.416076] usb usb4: Manufacturer: Linux 5.9.11 ehci_hcd
[ 2.421474] usb usb4: SerialNumber: 1c1c000.usb
[ 2.426509] hub 4-0:1.0: USB hub found
[ 2.430313] hub 4-0:1.0: 1 port detected
[ 2.435102] ehci-platform 1c1d000.usb: EHCI Host Controller
[ 2.440705] ehci-platform 1c1d000.usb: new USB bus registered, assigned bus number 5
[ 2.448778] ehci-platform 1c1d000.usb: irq 35, io mem 0x01c1d000
[ 2.479454] ehci-platform 1c1d000.usb: USB 2.0 started, EHCI 1.00
[ 2.485704] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[ 2.493974] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.501195] usb usb5: Product: EHCI Host Controller
[ 2.506068] usb usb5: Manufacturer: Linux 5.9.11 ehci_hcd
[ 2.511466] usb usb5: SerialNumber: 1c1d000.usb
[ 2.516461] hub 5-0:1.0: USB hub found
[ 2.520255] hub 5-0:1.0: 1 port detected
[ 2.525044] ohci-platform 1c1b400.usb: Generic Platform OHCI controller
[ 2.531696] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 6
[ 2.540334] ohci-platform 1c1b400.usb: irq 32, io mem 0x01c1b400
[ 2.613639] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.09
[ 2.621909] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.629121] usb usb6: Product: Generic Platform OHCI controller
[ 2.635045] usb usb6: Manufacturer: Linux 5.9.11 ohci_hcd
[ 2.640444] usb usb6: SerialNumber: 1c1b400.usb
[ 2.646043] hub 6-0:1.0: USB hub found
[ 2.649853] hub 6-0:1.0: 1 port detected
[ 2.654632] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[ 2.661285] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 7
[ 2.669264] ohci-platform 1c1c400.usb: irq 34, io mem 0x01c1c400
[ 2.743626] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.09
[ 2.751896] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.759109] usb usb7: Product: Generic Platform OHCI controller
[ 2.765031] usb usb7: Manufacturer: Linux 5.9.11 ohci_hcd
[ 2.770430] usb usb7: SerialNumber: 1c1c400.usb
[ 2.775438] hub 7-0:1.0: USB hub found
Welcome to LibreELEC (community): devel-20201205115124-c4f62a1!
[ OK ] Created slice system-modprobe.slice.
[ OK ] Created slice User and Session Slice.
[ OK ] Started Dispatch Password โฆts to Console Directory Watch.
[ OK ] Started Forward Password Rโฆuests to Wall Directory Watch.
[ OK ] Reached target Paths.
[ OK ] Reached target Slices.
[ OK ] Listening on RPCbind Server Activation Socket.
[ OK ] Reached target RPC Port Mapper.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket.
[ OK ] Listening on udev Control Socket.
[ OK ] Listening on udev Kernel Socket.
Mounting POSIX Message Queue File System...
Mounting Kernel Debug File System...
Mounting Variable Directory...
Starting Create kernel modules tree from overlays...
Starting Load Kernel Module configfs...
Starting Load Kernel Module drm...
Starting Load Kernel Module fuse...
Starting Show Version...
Starting Create Persistent Log Directory on /storage...
LibreELEC (community): devel-20201205115124-c4f62a1
Starting Setup NTP servers for timesyncd...
Starting Wait for Kernel Time Synchronisation...
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Kernel Debug File System.
[ OK ] Mounted Variable Directory.
[ OK ] Finished Create kernel modules tree from overlays.
[ OK ] Finished Load Kernel Module configfs.
[ OK ] Finished Load Kernel Module drm.
[ OK ] Finished Load Kernel Module fuse.
[ OK ] Finished Show Version.
[ OK ] Finished Create Persistent Log Directory on /storage.
[ OK ] Finished Setup NTP servers for timesyncd.
Mounting Kernel Configuration File System...
Starting Create list of stโฆodes for the current kernel...
Starting Setup machine-id...
Starting Mounting swapfile...
Starting Load Kernel Modules...
Starting Coldplug All udev Devices...
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Finished Create list of stโฆ nodes for the current kernel.
[ OK ] Finished Setup machine-id.
[ OK ] Finished Load Kernel Modules.
Starting Journal Service...
Starting Apply Kernel Variables...
Starting Create Static Device Nodes in /dev...
[ OK ] Started Journal Service.
[ OK ] Finished Apply Kernel Variables.
Starting Flush Journal to Persistent Storage...
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Finished Flush Journal to Persistent Storage.
[ OK ] Finished Mounting swapfile.
[ OK ] Reached target Swap.
Mounting Temporary Directory (/tmp)...
[ OK ] Mounted Temporary Directory (/tmp).
[ OK ] Finished Coldplug All udev Devices.
[ OK ] Reached target Local File Systems.
Starting Create Volatile Files and Directories...
[ OK ] Finished Create Volatile Files and Directories.
Starting Add random entropy from file...
Starting Generate system-wide /etc/environment file...
Starting Update hwdb.bin...
Starting OpenSSL configuration service...
Starting RPC Bind...
Starting Rebuild Journal Catalog...
Starting Update UTMP about System Boot/Shutdown...
Starting Setup Timezone data...
Starting Setup User cache dir...
Starting Setup User config dir...
[ OK ] Finished Generate system-wide /etc/environment file.
[ OK ] Started RPC Bind.
[ OK ] Finished OpenSSL configuration service.
[ OK ] Finished Rebuild Journal Catalog.
[ OK ] Finished Setup Timezone data.
[ OK ] Finished Setup User cache dir.
[ OK ] Finished Update UTMP about System Boot/Shutdown.
[ OK ] Finished Setup User config dir.
Starting Base Network Configuration...
[ OK ] Finished Base Network Configuration.
[ OK ] Reached target System Time Set.
[ OK ] Finished Add random entropy from file.
[ OK ] Finished Update hwdb.bin.
Starting Rule-based Manageโฆfor Device Events and Files...
[ OK ] Started Rule-based Manager for Device Events and Files.
[ OK ] Reached target System Initialization.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Timers.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Listening on lircd.socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting Broadcom SDIO Firmware Symlink Service...
Starting ConnMan VPN service...
Starting Set CPU frequency governor and its tunables...
Starting Cron daemon...
Starting D-Bus System Message Bus...
[ OK ] Started Eventlirc server daemon.
Starting Kodi clean debug logs...
Starting PulseAudio Sound Service...
Starting Samba Configuration...
Starting User Login Management...
[ OK ] Finished Broadcom SDIO Firmware Symlink Service.
[ OK ] Finished Set CPU frequency governor and its tunables.
[ OK ] Started D-Bus System Message Bus.
[ OK ] Started Cron daemon.
[ OK ] Finished Kodi clean debug logs.
[ OK ] Finished Samba Configuration.
[ OK ] Started ConnMan VPN service.
[ OK ] Started User Login Management.
[ OK ] Started PulseAudio Sound Service.
[ OK ] Reached target Sound Card.
[ OK ] Reached target Hardware activated USB gadget.
Starting Connection service...
[ OK ] Created slice system-udevil\x2dmount.slice.
Starting Udevil mount service...
[ OK ] Started Connection service.
[ OK ] Reached target Network.
[ OK ] Started Avahi Daemon.
[ OK ] Reached target Network is Online.
Starting Samba NMB Daemon...
Starting Hostname Service...
Starting WPA supplicant...
[ OK ] Finished Udevil mount service.
[ OK ] Started WPA supplicant.
[ OK ] Started Hostname Service.
[ OK ] Started Samba NMB Daemon.
Starting Samba SMB Daemon...
[ OK ] Started Samba SMB Daemon.
[ OK ] Reached target Multi-User System.
[ OK ] Reached target Graphical Interface.
Starting Kodi Media Center...
Starting LEDfix Service...
Starting Update UTMP about System Runlevel Changes...
[ OK ] Started Kodi Media Center.
[ OK ] Finished LEDfix Service.
[ OK ] Finished Update UTMP about System Runlevel Changes.