Hello,

first of all: Thank you!

Is Support for Realtek RTD1296 SoC e.g. used in the DS218 and DS220j possible?

Description of the problem

Adapter installation worked. Read 224 GB/s, Write 175 GB/s. Read seems stable, write goes to 0 MB/s after a few minutes, then adapter was not reachable any more with ping. After reboot normal again, 2 minutes later next crash.

Description of your products

DS2415+, 12x 4TB RAID 6, 4GB RAM. Worked stable with 1GB for 4 years.
Linux SRVDS2415 3.10.105 #25426 SMP Wed Jul 8 03:19:33 CST 2020 x86_64 GNU/Linux synology_avoton_2415+
DSM 6.2.3-25426 Update 2
Club 3D CAC-1420
Direct connection to ASUS mainboard with 2.5GB onboard, CAT6.

messages after crash:
2020-08-28T11:41:46+02:00 SRVDS2415 smbd: ../source3/lib/recvfile.c:216 recvfile failed(-1): Broken pipe, count=[1048576] total tx/tx=[856800/856800] rwbytes=[856800/856800]

Output of dmesg command

Output of lsusb command

|__usb1 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (ehci_hcd 0000:00:16.0) hub
|__1-1 8087:07db:0002 09 2.00 480MBit/s 0mA 1IF ( ffffffd1ffffffb2ffffffdbffffffad) hub
|__1-1.1 f400:f400:0100 00 2.00 480MBit/s 200mA 1IF (Synology DiskStation 65004C24D3020557)
|__usb2 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (Linux 3.10.105 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub
|__usb3 1d6b:0003:0310 09 3.00 5000MBit/s 0mA 1IF (Linux 3.10.105 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub
|__3-1 0bda:8156:3000 00 3.20 5000MBit/s 512mA 1IF (Realtek USB 10/100/1G/2.5G LAN 000000001)

### Output of ``ifconfig -a`` command
eth0      Link encap:Ethernet  HWaddr 00:11:32:3C:CB:EB
          inet addr:192.168.17.126  Bcast:192.168.17.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:16313 errors:0 dropped:0 overruns:0 frame:0
          TX packets:35513 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:2017748 (1.9 MiB)  TX bytes:24269030 (23.1 MiB)

eth1      Link encap:Ethernet  HWaddr 00:11:32:3C:CB:EC
          inet addr:169.254.173.118  Bcast:169.254.255.255  Mask:255.255.0.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth2      Link encap:Ethernet  HWaddr 00:11:32:3C:CB:ED
          inet addr:169.254.18.80  Bcast:169.254.255.255  Mask:255.255.0.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth3      Link encap:Ethernet  HWaddr 00:11:32:3C:CB:EE
          inet addr:169.254.156.120  Bcast:169.254.255.255  Mask:255.255.0.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)


eth4 is CLUB3D adapter
eth4      Link encap:Ethernet  HWaddr A0:CE:C8:CD:45:9C
          inet addr:192.168.16.126  Bcast:192.168.16.255  Mask:255.255.255.0
          inet6 addr: fe80::a2ce:c8ff:fecd:459c/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:12951755 errors:0 dropped:0 overruns:0 frame:0
          TX packets:909047 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:19605287541 (18.2 GiB)  TX bytes:51418960 (49.0 MiB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:3252 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3252 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:471094 (460.0 KiB)  TX bytes:471094 (460.0 KiB)

sit0      Link encap:IPv6-in-IPv4
          NOARP  MTU:1480  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

Has anyone tried to tweak this?

Test equipment: DS218 +(DSM 6.2.3 25426), Ugreen USB A to 2.5G (RTL8156), ASUS AX86U

When the network cable is inserted into the 2.5G LAN port of the router, the 2.5G network can be recognized, but it can not work normally.
Unable to Ping, unable to access NAS

When the network cable is inserted into the 1g LAN port of the router, the 1g network can be identified and the NAS can be accessed normally.

Hello,

I noticed that there is a new r8152.c driver form Realtek released 2020-Apr-20. File size is 556KB.
ver. r8152-2.13.0

The current r8152.c file size is 367KB. r8152-2.12.0

r8152-2.13.0.zip

Working with DS916+ and PLUGABLE 2.5GBPS USB ETHERNET ADAPTER
After installation I had to restart the Synology NAS for it to show up.

Synology Version: DSM 6.2.3-25426 Update 2
Driver Version: 2.12.0-3

Hallo,
the new driver version 2.13.0-1 works perfect with 2 DS918+ (2 CLUB 3D CAC-1420 adapters on everyone DS918+)

Thanks for all.

Great Job !!

has anyone sucesfully used the rtd1296 driver - I'm seeing speed drop to zero (requiring if down/up to clear) testing it with full duplex loads (either 'real world' copying large files simultaneously in both directions, or synthetically testing using iperf3)

Thanks in advance!

Hi~~
Could you please support Support DS1513+ with ASUSTOR AS-U2.5G?
Due to I would like to use the ASUSTOR AS-U2.5G on a DS1513+ with DSM 6.2.2, thanks a lot.

Seems to work just fine on an RS1219+ unit.

The broadwell driver is installed on the DS3617xs normally (r8152-broadwell-2.12.0-1.spk or r8152-broadwell-2.12.0-3.spk is available), but does not start. In the control panel, the status is "Stopped". The USB module on the RTL8156B chip, manufacturer OPEN-SMART is connected. How do I solve this problem?
PS:
I'm not a good Linux expert. I executed the command "sudo dmesg" and got a lot of lines among which there was an error related to r8152: version magic '4.4.59+ SMP preempt mod_unload ' should be '3.10.102 SMP mod_unload ' What is this?

Description of the problem

I have installed the latest driver and want to use my LAN3 as the main LAN. The other internal 2 LANs should not be used. I cannot select LAN3 under Virtual Machine Manager Network. Does anyone know the problem?

Replace this line with your answer.

Description of your products

• the product name of your NAS model DS918+
  • and output of uname -a command
  • DSM version DSM 6.2.3-25426
  • Club3D CAC-1420 2.5GbE USB-LAN

I really really really.. need ds1618+ Version which is used denverton architecture.
Could you please make ds1618+ (denverton) version?

DS415+ (avoton) confirmed working ok with Club 3D CAC-1420
DSM version: 6.2.3
Driver version: r8152-avoton-2.12.0-3.spk
Switch: QNAP QSW-1105-5T

One issue I noticed when using USB network adapter is that IPv6 address is assigned even though the option is set to OFF in DSM.
I have not tested MTU changes.

Using rear USB port (front 3.0 is not present on this model).

Description of the problem

Is it possible to get the driver for a Synology DS216play ? It seems to be a monaco procesor
Thank you

Description of your products

• the product name of your NAS model :
  DS216play
  • and output of uname -a command
    Linux DSLaurent 3.10.105 #24922 SMP Tue Jul 9 18:27:16 CST 2019 armv7l GNU/Linux synology_monaco_ds216play

- DSM version x.x

DSM 6.2.2-24922 Update 4

• the product name of the ethernet dongle
  RTL8152 Fast Ethernet Adapter - Realtek Semiconductor Corp.

Description of your environment

• connect directly to a PC or using a hub
  Device connected directly to the Synology
  • PC: NIC model name or chipset name
    RTL8152 Fast Ethernet Adapter - Realtek Semiconductor Corp.
  • Hub: model name
    No Hub
• cable category (Cat.5e or Cat.6 or Cat.7)
  Cat.6

Output of dmesg command

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.10.105 (root@build1) (gcc version 4.9.3 20150311 (prerelease) (crosstool-NG 1.20.0) ) #24922 SMP Tue Jul 9 18:27:16 CST 2019
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: STi SoC with Flattened Device Tree, model: STiH410 B2120
[ 0.000000] Ignoring memory below PHYS_OFFSET: 0x40000000-0x43000000
[ 0.000000] Ignoring memory below PHYS_OFFSET: 0x42000000-0x43000000
[ 0.000000] cma: CMA: reserved 16 MiB at 5f000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] On node 0 totalpages: 118784
[ 0.000000] free_area_init_node: node 0, pgdat 806ddf40, node_mem_map 8073b000
[ 0.000000] Normal zone: 928 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 118784 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 7 pages/cpu @80b29000 s6976 r8192 d13504 u32768
[ 0.000000] pcpu-alloc: s6976 r8192 d13504 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 117856
[ 0.000000] Kernel command line: console=ttyS0,115200 CONSOLE=/dev/ttyS0 ip=off mtdparts=stm-nand-bch.0:0x500000(boot),-(rfs) bpa2parts=BPA2_Region|aud-coded|aud-transcoded|vid-coded|vid-transcoded|vid-raw-input|vid-output-0|vid-decimated-1|vid-copied-1|vid-macroblock-0|vid-extra-data-0|vid-extra-data-1|v4l2-coded-video-buffers|vid-enc-data-0|vid-enc-scaled-0|vid-encoded-0|v4l2-clut|v4l2-grab|gfx-memory|aud-codec-data|vid-codec-data|aud-output-0|aud-output-1|vid-output-1|vid-decimated-0|vid-copied-0|vid-macroblock-1|blitter|vid-enc-data-1|vid-enc-scaled-1|vid-encoded-1|coredisplay-video|multicom|hades-l3|BPA2_Region0|BPA2_Region1:480M:0x62000000,v4l2-vb2|v4l2-stmc8jpg|v4l2-stmvout|v4l2-compo:24M:0x60800000,coprocs:32M:0x40000000,modules|audio:8M:0x60000000,bigphysarea|te-buffers|m2m-ca3:48M:0x48000000,STMCReserve:32768:0x47FF8000 vmalloc=775m mem=503316480@0x42000000 root=/dev/md0 rw syno_hw_version=DS216play hd_power_on_seq=2 ihd_num=2 netif_num=1 flash_size=8 phys_memsize=1024 rev=r1
[ 0.000000] bpa2: partition 'BPA2_Region' created at 0x62000000 (high), size 491520 kB (0x1e000000 B)
[ 0.000000] bpa2: partition 'v4l2-vb2' created at 0x60800000 (high), size 24576 kB (0x01800000 B)
[ 0.000000] bpa2: partition 'coprocs' created at 0x40000000 (high), size 32768 kB (0x02000000 B)
[ 0.000000] bpa2: partition 'modules' created at 0x60000000 (high), size 8192 kB (0x00800000 B)
[ 0.000000] bpa2: partition 'bigphysarea' created at 0x48000000 (low), size 49152 kB (0x03000000 B)
[ 0.000000] bpa2: partition 'STMCReserve' created at 0x47ff8000 (low), size 32 kB (0x00008000 B)
[ 0.000000] Synology Hardware Version: DS216play-j
[ 0.000000] Internal HD num: 2
[ 0.000000] Internal netif num: 1
[ 0.000000] Synology Hardware Revision: r1
[ 0.000000] SYNO Transcoding Memory Mode: 3
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 464MB = 464MB total
[ 0.000000] Memory: 393428k/393428k available, 81708k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0x9d800000 - 0xff000000 (1560 MB)
lowmem : 0x80000000 - 0x9d000000 ( 464 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x80008000 - 0x80665b18 (6519 kB)
.init : 0x80666000 - 0x806a0b40 ( 235 kB)
.data : 0x806a2000 - 0x806dea00 ( 243 kB)
.bss : 0x806dea00 - 0x8073ac24 ( 369 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] st-lpc: lpc_clk running @ 30000000 Hz
[ 0.000000] sched_clock: 32 bits at 30MHz, resolution 33ns, wraps every 143165ms
[ 0.000000] st-lpc: clocksource initialised: iomem: 9d81c000
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x10480000, Cache size: 1048576 B
[ 0.000000] Console: colour dummy device 80x30
[ 0.001789] Calibrating delay loop... 2996.63 BogoMIPS (lpj=14983168)
[ 0.060214] pid_max: default: 32768 minimum: 301
[ 0.060283] Security Framework initialized
[ 0.060299] AppArmor: AppArmor initialized
[ 0.060326] Mount-cache hash table entries: 512
[ 0.060680] CPU: Testing write buffer coherency: ok
[ 0.060986] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.061564] Setting up static identity map for 0x804c6c50 - 0x804c6d2c
[ 0.062011] CPU1: Booted secondary processor
[ 0.120234] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.120284] Brought up 2 CPUs
[ 0.120294] SMP: Total of 2 processors activated (5985.89 BogoMIPS).
[ 0.120297] CPU: All CPU(s) started in SVC mode.
[ 0.120650] devtmpfs: initialized
[ 0.123789] xor: measuring software checksum speed
[ 0.220222] arm4regs : 2325.200 MB/sec
[ 0.320221] 8regs : 1668.400 MB/sec
[ 0.420221] 32regs : 1695.200 MB/sec
[ 0.420226] xor: using function: arm4regs (2325.200 MB/sec)
[ 0.420233] pinctrl core: initialized pinctrl subsystem
[ 0.420581] regulator-dummy: no parameters
[ 0.421179] NET: Registered protocol family 16
[ 0.424382] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.428552] syscon 9620000.sbc-syscfg: regmap [mem 0x09620000-0x09620fff] registered
[ 0.428693] syscon 9280000.front-syscfg: regmap [mem 0x09280000-0x09280fff] registered
[ 0.428819] syscon 9290000.rear-syscfg: regmap [mem 0x09290000-0x09290fff] registered
[ 0.428936] syscon 92a0000.flash-syscfg: regmap [mem 0x092a0000-0x092a0fff] registered
[ 0.429067] syscon 9600000.fvdp-lite-syscfg: regmap [mem 0x09600000-0x09600fff] registered
[ 0.429186] syscon 92b0000.core-syscfg: regmap [mem 0x092b0000-0x092b0fff] registered
[ 0.429309] syscon 94b5100.lpm-syscfg: regmap [mem 0x094b5100-0x094b60ff] registered
[ 0.442684] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.442692] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.442847] st-pinctrl 961f080.pin-controller-sbc: nbanks = 6
[ 0.442853] st-pinctrl 961f080.pin-controller-sbc: nfunctions = 14
[ 0.442859] st-pinctrl 961f080.pin-controller-sbc: ngroups = 27
[ 0.443006] st-pinctrl 961f080.pin-controller-sbc: PIO0 bank added.
[ 0.443181] st-pinctrl 961f080.pin-controller-sbc: PIO1 bank added.
[ 0.443341] st-pinctrl 961f080.pin-controller-sbc: PIO2 bank added.
[ 0.443509] st-pinctrl 961f080.pin-controller-sbc: PIO3 bank added.
[ 0.443666] st-pinctrl 961f080.pin-controller-sbc: PIO4 bank added.
[ 0.443826] st-pinctrl 961f080.pin-controller-sbc: PIO5 bank added.
[ 0.443912] st-pinctrl 961f080.pin-controller-sbc: Function[0 name:wakeup-pin, groups:1]
[ 0.443922] st-pinctrl 961f080.pin-controller-sbc: Function[1 name:rc, groups:1]
[ 0.443932] st-pinctrl 961f080.pin-controller-sbc: Function[2 name:sbc_serial0, groups:1]
[ 0.443942] st-pinctrl 961f080.pin-controller-sbc: Function[3 name:sbc_serial1, groups:1]
[ 0.443952] st-pinctrl 961f080.pin-controller-sbc: Function[4 name:i2c10, groups:1]
[ 0.443962] st-pinctrl 961f080.pin-controller-sbc: Function[5 name:i2c11, groups:1]
[ 0.443977] st-pinctrl 961f080.pin-controller-sbc: Function[6 name:keyscan, groups:1]
[ 0.444031] st-pinctrl 961f080.pin-controller-sbc: Function[7 name:gmac1, groups:8]
[ 0.444045] st-pinctrl 961f080.pin-controller-sbc: Function[8 name:pwm1, groups:4]
[ 0.444059] st-pinctrl 961f080.pin-controller-sbc: Function[9 name:spi10, groups:2]
[ 0.444072] st-pinctrl 961f080.pin-controller-sbc: Function[10 name:spi11, groups:2]
[ 0.444085] st-pinctrl 961f080.pin-controller-sbc: Function[11 name:spi12, groups:2]
[ 0.444094] st-pinctrl 961f080.pin-controller-sbc: Function[12 name:cec0, groups:1]
[ 0.444112] st-pinctrl 961f080.pin-controller-sbc: Function[13 name:hdmirx0, groups:1]
[ 0.444211] st-pinctrl 920f080.pin-controller-front0: nbanks = 10
[ 0.444217] st-pinctrl 920f080.pin-controller-front0: nfunctions = 24
[ 0.444223] st-pinctrl 920f080.pin-controller-front0: ngroups = 53
[ 0.444366] st-pinctrl 920f080.pin-controller-front0: PIO10 bank added.
[ 0.444529] st-pinctrl 920f080.pin-controller-front0: PIO11 bank added.
[ 0.444693] st-pinctrl 920f080.pin-controller-front0: PIO12 bank added.
[ 0.444863] st-pinctrl 920f080.pin-controller-front0: PIO13 bank added.
[ 0.445026] st-pinctrl 920f080.pin-controller-front0: PIO14 bank added.
[ 0.445191] st-pinctrl 920f080.pin-controller-front0: PIO15 bank added.
[ 0.445358] st-pinctrl 920f080.pin-controller-front0: PIO16 bank added.
[ 0.445517] st-pinctrl 920f080.pin-controller-front0: PIO17 bank added.
[ 0.445681] st-pinctrl 920f080.pin-controller-front0: PIO18 bank added.
[ 0.445847] st-pinctrl 920f080.pin-controller-front0: PIO19 bank added.
[ 0.445943] st-pinctrl 920f080.pin-controller-front0: Function[0 name:serial0, groups:4]
[ 0.445962] st-pinctrl 920f080.pin-controller-front0: Function[1 name:serial1, groups:4]
[ 0.445981] st-pinctrl 920f080.pin-controller-front0: Function[2 name:serial2, groups:1]
[ 0.446002] st-pinctrl 920f080.pin-controller-front0: Function[3 name:mmc1, groups:1]
[ 0.446014] st-pinctrl 920f080.pin-controller-front0: Function[4 name:i2c0, groups:1]
[ 0.446025] st-pinctrl 920f080.pin-controller-front0: Function[5 name:i2c1, groups:1]
[ 0.446035] st-pinctrl 920f080.pin-controller-front0: Function[6 name:i2c2, groups:1]
[ 0.446052] st-pinctrl 920f080.pin-controller-front0: Function[7 name:i2c3, groups:3]
[ 0.446076] st-pinctrl 920f080.pin-controller-front0: Function[8 name:spi0, groups:4]
[ 0.446099] st-pinctrl 920f080.pin-controller-front0: Function[9 name:spi1, groups:4]
[ 0.446129] st-pinctrl 920f080.pin-controller-front0: Function[10 name:spi2, groups:6]
[ 0.446160] st-pinctrl 920f080.pin-controller-front0: Function[11 name:spi3, groups:6]
[ 0.446181] st-pinctrl 920f080.pin-controller-front0: Function[12 name:systrace, groups:1]
[ 0.446190] st-pinctrl 920f080.pin-controller-front0: Function[13 name:scr0, groups:1]
[ 0.446199] st-pinctrl 920f080.pin-controller-front0: Function[14 name:scr1, groups:1]
[ 0.446229] st-pinctrl 920f080.pin-controller-front0: Function[15 name:tsin0, groups:2]
[ 0.446259] st-pinctrl 920f080.pin-controller-front0: Function[16 name:tsin1, groups:2]
[ 0.446288] st-pinctrl 920f080.pin-controller-front0: Function[17 name:tsin2, groups:2]
[ 0.446302] st-pinctrl 920f080.pin-controller-front0: Function[18 name:tsin3, groups:1]
[ 0.446317] st-pinctrl 920f080.pin-controller-front0: Function[19 name:tsin4, groups:1]
[ 0.446338] st-pinctrl 920f080.pin-controller-front0: Function[20 name:tsin5, groups:2]
[ 0.446368] st-pinctrl 920f080.pin-controller-front0: Function[21 name:tsout0, groups:2]
[ 0.446382] st-pinctrl 920f080.pin-controller-front0: Function[22 name:tsout1, groups:1]
[ 0.446404] st-pinctrl 920f080.pin-controller-front0: Function[23 name:mtsin0, groups:1]
[ 0.446495] st-pinctrl 921f080.pin-controller-front1: nbanks = 1
[ 0.446501] st-pinctrl 921f080.pin-controller-front1: nfunctions = 1
[ 0.446507] st-pinctrl 921f080.pin-controller-front1: ngroups = 1
[ 0.446652] st-pinctrl 921f080.pin-controller-front1: PIO20 bank added.
[ 0.446755] st-pinctrl 921f080.pin-controller-front1: Function[0 name:tsin4, groups:1]
[ 0.446831] st-pinctrl 922f080.pin-controller-rear: nbanks = 6
[ 0.446838] st-pinctrl 922f080.pin-controller-rear: nfunctions = 11
[ 0.446843] st-pinctrl 922f080.pin-controller-rear: ngroups = 17
[ 0.446989] st-pinctrl 922f080.pin-controller-rear: PIO30 bank added.
[ 0.447167] st-pinctrl 922f080.pin-controller-rear: PIO31 bank added.
[ 0.447332] st-pinctrl 922f080.pin-controller-rear: PIO32 bank added.
[ 0.447489] st-pinctrl 922f080.pin-controller-rear: PIO33 bank added.
[ 0.447666] st-pinctrl 922f080.pin-controller-rear: PIO34 bank added.
[ 0.447832] st-pinctrl 922f080.pin-controller-rear: PIO35 bank added.
[ 0.448068] st-pinctrl 922f080.pin-controller-rear: Function[0 name:dvo, groups:2]
[ 0.448083] st-pinctrl 922f080.pin-controller-rear: Function[1 name:i2c4, groups:1]
[ 0.448096] st-pinctrl 922f080.pin-controller-rear: Function[2 name:i2c5, groups:1]
[ 0.448109] st-pinctrl 922f080.pin-controller-rear: Function[3 name:usb0, groups:1]
[ 0.448123] st-pinctrl 922f080.pin-controller-rear: Function[4 name:usb1, groups:1]
[ 0.448143] st-pinctrl 922f080.pin-controller-rear: Function[5 name:usb3, groups:1]
[ 0.448155] st-pinctrl 922f080.pin-controller-rear: Function[6 name:pwm0, groups:1]
[ 0.448190] st-pinctrl 922f080.pin-controller-rear: Function[7 name:spi4, groups:4]
[ 0.448227] st-pinctrl 922f080.pin-controller-rear: Function[8 name:i2s_out, groups:2]
[ 0.448264] st-pinctrl 922f080.pin-controller-rear: Function[9 name:i2s_in, groups:2]
[ 0.448275] st-pinctrl 922f080.pin-controller-rear: Function[10 name:spdif_out, groups:1]
[ 0.448369] st-pinctrl 923f080.pin-controller-flash: nbanks = 3
[ 0.448375] st-pinctrl 923f080.pin-controller-flash: nfunctions = 3
[ 0.448381] st-pinctrl 923f080.pin-controller-flash: ngroups = 3
[ 0.448514] st-pinctrl 923f080.pin-controller-flash: PIO40 bank added.
[ 0.448683] st-pinctrl 923f080.pin-controller-flash: PIO41 bank added.
[ 0.448853] st-pinctrl 923f080.pin-controller-flash: PIO42 bank added.
[ 0.448978] st-pinctrl 923f080.pin-controller-flash: Function[0 name:mmc0, groups:1]
[ 0.449008] st-pinctrl 923f080.pin-controller-flash: Function[1 name:fsm, groups:1]
[ 0.449070] st-pinctrl 923f080.pin-controller-flash: Function[2 name:nand, groups:1]
[ 0.450961] reset-stih407 powerdown-controller.8: registered
[ 0.452683] reset-stih407 softreset-controller.10: registered
[ 0.452880] reset-stih407 picophyreset-controller.11: registered
[ 0.455705] st-clk clocks.0: SoC clock tree intialized
[ 0.466087] bio: create slab at 0
[ 0.630480] raid6: int32x1 gen() 241 MB/s
[ 0.800386] raid6: int32x1 xor() 176 MB/s
[ 0.970411] raid6: int32x2 gen() 326 MB/s
[ 1.140259] raid6: int32x2 xor() 216 MB/s
[ 1.310383] raid6: int32x4 gen() 314 MB/s
[ 1.480281] raid6: int32x4 xor() 218 MB/s
[ 1.650241] raid6: int32x8 gen() 350 MB/s
[ 1.820316] raid6: int32x8 xor() 221 MB/s
[ 1.820321] raid6: using algorithm int32x8 gen() (350 MB/s)
[ 1.820325] raid6: .... xor() 221 MB/s, rmw enabled
[ 1.820328] raid6: using intx1 recovery algorithm
[ 1.820585] st-fdma 8e20000.fdma-mpe: IRQ: 37
[ 1.820603] st-fdma 8e20000.fdma-mpe: Base address: 9d8c0000
[ 1.822198] st-fdma 8e40000.fdma-mpe: IRQ: 39
[ 1.822212] st-fdma 8e40000.fdma-mpe: Base address: 9d9c0000
[ 1.823729] st-fdma 8e60000.fdma-mpe: IRQ: 41
[ 1.823754] st-fdma 8e60000.fdma-mpe: Base address: 9da00000
[ 1.825528] vmmc0: at 3300 mV
[ 1.825575] st-vsense 9061004.voltage-regulator: vmmc0 vsense voltage regulator registered
[ 1.825934] vgaarb: loaded
[ 1.826225] SCSI subsystem initialized
[ 1.826437] libata version 3.00 loaded.
[ 1.826673] media: Linux media interface: v0.10
[ 1.826735] Linux video capture interface: v2.00
[ 1.826944] pps_core: LinuxPPS API ver. 1 registered
[ 1.826950] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [email protected]
[ 1.827000] PTP clock support registered
[ 1.827918] Switching to clocksource st-lpc clocksource
[ 1.828181] AppArmor: AppArmor Filesystem Enabled
[ 1.837304] NET: Registered protocol family 2
[ 1.837685] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.837724] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.837759] TCP: Hash tables configured (established 4096 bind 4096)
[ 1.837800] TCP: reno registered
[ 1.837807] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 1.837827] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 1.837999] NET: Registered protocol family 1
[ 1.838155] RPC: Registered named UNIX socket transport module.
[ 1.838160] RPC: Registered udp transport module.
[ 1.838164] RPC: Registered tcp transport module.
[ 1.838167] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.838174] PCI: CLS 0 bytes, default 64
[ 1.838279] Trying to unpack rootfs image as initramfs...
[ 3.169683] Freeing initrd memory: 4048K (80c0a000 - 80ffe000)
[ 3.171679] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 3.173120] sti pm: Copying poke table & poke loop to buffer
[ 3.173130] sti pm: entering prepare:CONTROLLER PASSIVE STANDBY
[ 3.173136] sti pm: support mode: CONTROLLER PASSIVE STANDBY
[ 3.173139] sti pm: Suspend support registered
[ 3.173298] synology : fan ctrl initialized.
[ 3.173308] synology : fan sense initialized.
[ 3.173321] synology : sata power initialized.
[ 3.173337] synology : model id initialized.
[ 3.173345] synology : disk led ctrl initialized.
[ 3.173353] synology : phy led ctrl initialized.
[ 3.174638] Initialise module verification
[ 3.174674] audit: initializing netlink socket (disabled)
[ 3.174697] type=2000 audit(3.160:1): initialized
[ 3.221752] st-pinctrl 920f080.pin-controller-front0: maps: function systrace group systrace-default num 6
[ 3.221867] stm-systrace 9180000.systrace: Systrace: syscfg0=0x003f0000 (prev: 0x003f0000)
[ 3.221878] stm-systrace 9180000.systrace: Systrace: syscfg1=0x00580058 (prev: 0x00580058)
[ 3.221887] stm-systrace 9180000.systrace: Systrace: syscfg2=0x00990098 (prev: 0x00990098)
[ 3.221896] stm-systrace 9180000.systrace: Systrace: syscfg3=0x00530050 (prev: 0x00530050)
[ 3.221904] stm-systrace 9180000.systrace: Systrace: syscfg4=0x00550054 (prev: 0x00550054)
[ 3.221913] stm-systrace 9180000.systrace: Systrace: syscfg5=0x00570056 (prev: 0x00570056)
[ 3.221922] stm-systrace 9180000.systrace: Systrace: syscfg6=0x03ff03ff (prev: 0x03ff0000)
[ 3.221932] stm-systrace 9180000.systrace: Systrace: STM_CR[0x0000] = 0x00000600 (prev. 0x00000000)
[ 3.221941] stm-systrace 9180000.systrace: Systrace: STM_MCR[0x0008] = 0x00000000 (prev. 0x00000000)
[ 3.221949] stm-systrace 9180000.systrace: Systrace: STM_TER[0x0010] = 0x000003ff (prev. 0x000003ff)
[ 3.221958] stm-systrace 9180000.systrace: Systrace: STM_FTR[0x0080] = 0x00000001 (prev. 0x00000000)
[ 3.221966] stm-systrace 9180000.systrace: Systrace: STM_CTR[0x0088] = 0x00000001 (prev. 0x00000000)
[ 3.221972] Systrace: STM IP revision is V3
[ 3.221976] Systrace: STM_PID=0x00680dec(0x00680dec)
[ 3.221980] Systrace: STM_CID=0xb105f00d(0xb105f00d)
[ 3.221983] MTT: registering output driver stm
[ 3.221989] stm-systrace 9180000.systrace: Systrace: driver probed.
[ 3.234402] VFS: Disk quotas dquot_6.5.2
[ 3.234704] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.237787] NFS: Registering the id_resolver key type
[ 3.237812] Key type id_resolver registered
[ 3.237817] Key type id_legacy registered
[ 3.237844] msgmni has been set to 808
[ 3.238511] async_tx: api initialized (async)
[ 3.238518] Key type asymmetric registered
[ 3.238523] Asymmetric key parser 'x509' registered
[ 3.238929] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 3.238937] io scheduler noop registered
[ 3.238956] io scheduler cfq registered (default)
[ 3.360746] STMicroelectronics ASC driver initialized
[ 3.360886] st-pinctrl 961f080.pin-controller-sbc: maps: function sbc_serial0 group sbc_serial0-0 num 3
[ 3.360979] 9530000.serial: ttyS0 at MMIO 0x9530000 (irq = 170) is a st-asc
[ 5.018622] console [ttyS0] enabled
[ 5.022429] st-pinctrl 961f080.pin-controller-sbc: maps: function sbc_serial1 group sbc_serial1-0 num 3
[ 5.031889] 9531000.serial: ttyS1 at MMIO 0x9531000 (irq = 171) is a st-asc
[ 5.039804] st-hwrandom 8a89000.rng: ST Random Number Generator Device Probe Successful
[ 5.056468] brd: module loaded
[ 5.059526] Loading iSCSI transport class v2.0-870.
[ 5.067066] ahci ahci.0: can't get clock
[ 5.071002] miphy28lp-phy 9b22000.miphy28lp: miphy28lp_phy_init_sata
[ 5.077344] miphy28lp-phy 9b22000.miphy28lp: sata-up mode, addr 0x9d8e4000
[ 5.088285] ahci ahci.0: forcing PORTS_IMPL to 0x1
[ 5.093086] ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 5.101076] ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 5.110309] scsi0 : ahci_platform
[ 5.114054] ata1: SATA max UDMA/133 mmio [mem 0x09b20000-0x09b20fff] port 0x100 irq 191
[ 8.657964] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 8.664633] ata1.00: ATA-9: WDC WD20EFRX-68EUZN0, 82.00A82, max UDMA/133
[ 8.671334] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 8.678116] ata1.00: SN: WD-WCC4M0PZ5NH9
[ 8.682886] ata1.00: configured for UDMA/133
[ 8.687776] scsi 0:0:0:0: Direct-Access WDC WD20EFRX-68EUZN0 82.0 PQ: 0 ANSI: 5
[ 8.697341] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 8.705088] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 8.710464] sd 0:0:0:0: [sda] Write Protect is off
[ 8.711199] ahci ahci.1: can't get clock
[ 8.711206] miphy28lp-phy 9b2a000.miphy28lp: miphy28lp_phy_init_sata
[ 8.711210] miphy28lp-phy 9b2a000.miphy28lp: sata-up mode, addr 0x9d8ea000
[ 8.713112] ahci ahci.1: forcing PORTS_IMPL to 0x1
[ 8.713139] ahci ahci.1: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 8.713145] ahci ahci.1: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 8.752795] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 8.752866] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.763416] scsi1 : ahci_platform
[ 8.767195] ata2: SATA max UDMA/133 mmio [mem 0x09b28000-0x09b28fff] port 0x100 irq 202
[ 8.775223] Delay 5 seconds to wait for disk 2 ready.
[ 8.778719] sda: sda1 sda2 sda3 < sda5 >
[ 8.784747] sd 0:0:0:0: [sda] Attached SCSI disk
[ 22.217965] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 22.224600] ata2.00: ATA-9: WDC WD20EFRX-68EUZN0, 82.00A82, max UDMA/133
[ 22.231301] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 22.238083] ata2.00: SN: WD-WCC4M7LTLFTU
[ 22.242847] ata2.00: configured for UDMA/133
[ 22.247714] scsi 1:0:0:0: Direct-Access WDC WD20EFRX-68EUZN0 82.0 PQ: 0 ANSI: 5
[ 22.257283] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 22.265030] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 22.270378] sd 1:0:0:0: [sdb] Write Protect is off
[ 22.272731] st-pinctrl 923f080.pin-controller-flash: maps: function fsm group fsm num 7
[ 22.272989] stm-spi-fsm 9022000.spifsm: No provision for SPI reset on boot-from-spi system
[ 22.272994] stm-spi-fsm 9022000.spifsm: Individual block locking scheme enabled
[ 22.272999] stm-spi-fsm 9022000.spifsm: found device: n25q064, size = 800000 (8MiB) erasesize = 0x00010000 (64KiB)
[ 22.273013] Searching for RedBoot partition table in n25q064 at offset 0x7f0000
[ 22.278632] 6 RedBoot partitions found on MTD device n25q064
[ 22.278634] Creating 6 MTD partitions on "n25q064":
[ 22.278639] 0x000000000000-0x0000000c0000 : "RedBoot"
[ 22.284723] 0x0000000c0000-0x000000390000 : "zImage"
[ 22.286362] 0x000000390000-0x0000007d0000 : "rd.gz"
[ 22.288018] 0x0000007d0000-0x0000007e0000 : "vendor"
[ 22.288041] vender Mac0 address : 00:11:32:74:ea:c5
[ 22.288045] vender Mac1 doesn't set ucSum:0x00 Buf:0x00 Sum:0.
[ 22.288047] vender Mac2 doesn't set ucSum:0x00 Buf:0x00 Sum:0.
[ 22.288050] vender Mac3 doesn't set ucSum:0x00 Buf:0x00 Sum:0.
[ 22.289703] serial number='1730NEN106700'
[ 22.289704] 0x0000007e0000-0x0000007f0000 : "RedBoot Config"
[ 22.291332] 0x0000007f0000-0x000000800000 : "FIS directory"
[ 22.297214] st-pinctrl 961f080.pin-controller-sbc: maps: function gmac1 group rgmii1-0 num 13
[ 22.297223] st-pinctrl 961f080.pin-controller-sbc: maps: function gmac1 group rgmii1-mdio num 3
[ 22.297415] stmmaceth 9630000.dwmac: phy-addr property limits bus scan to this addr
[ 22.297524] stmmac - user ID: 0xca, Synopsys ID: 0x37
[ 22.297526] Ring mode enabled
[ 22.297529] DMA HW capability register supported
[ 22.297530] Enhanced/Alternate descriptors
[ 22.297531] Enabled extended descriptors
[ 22.297533] RX Checksum Offload Engine supported (type 2)
[ 22.297535] TX Checksum insertion supported
[ 22.297536] Wake-Up On Lan supported
[ 22.297554] Enable RX Mitigation via HW Watchdog Timer
[ 22.299714] libphy: stmmac: probed
[ 22.299719] eth0: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01) active
[ 22.301159] i2c /dev entries driver
[ 22.301590] st-pinctrl 922f080.pin-controller-rear: maps: function i2c4 group i2c4-default num 3
[ 22.328643] st-i2c 9844000.i2c: ST I2C(0x0) initialized
[ 22.328685] st-pinctrl 922f080.pin-controller-rear: maps: function i2c5 group i2c5-default num 3
[ 22.328731] st-i2c 9845000.i2c: No ID specified in DT alias
[ 22.331903] st_thermal 91a0000.temp0: STMicroelectronics thermal sensor initialised
[ 22.333163] st-lpc-wdt 8787000.lpc_wdt: LPC Watchdog driver registered, reset type is cold
[ 22.333597] md: linear personality registered for level -1
[ 22.333600] md: raid0 personality registered for level 0
[ 22.333602] md: raid1 personality registered for level 1
[ 22.333604] md: raid10 personality registered for level 10
[ 22.334007] md: raid6 personality registered for level 6
[ 22.334010] md: raid5 personality registered for level 5
[ 22.334012] md: raid4 personality registered for level 4
[ 22.334839] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: [email protected]
[ 22.335550] sdhci: Secure Digital Host Controller Interface driver
[ 22.335551] sdhci: Copyright(c) Pierre Ossman
[ 22.335552] sdhci-pltfm: SDHCI platform and OF driver helper
[ 22.541764] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 22.541894] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.552588] Mali: Mali device driver loaded
[ 22.553531] ST_DDR CNTRL driver registered
[ 22.557930] st-lpm driver registered
[ 22.561901] TCP: cubic registered
[ 22.565207] NET: Registered protocol family 17
[ 22.569707] Key type dns_resolver registered
[ 22.574089] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 22.581790] Registering SWP/SWPB emulation handler
[ 22.586908] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 22.597000] Loading module verification blacklist certificates
[ 22.602898] Loading module verification certificates
[ 22.607916] MODSIGN: Loaded cert 'Synology SDG kernel module signing key: 7bd0b0d6bcd31651c22ce3978bdc8c8bdc417329'
[ 22.622967] MODSIGN: Loaded cert 'Synology Root Certification Authority: f2c075361f168425f8b5ef31b796406c3aab2089'
[ 22.627967] sdb: sdb1 sdb2 sdb3 < sdb5 >
[ 22.637408] MODSIGN: Loaded cert 'Synology Kernel Module Signing Certification Authority: 600839b5d127e0e11d817a31f0575d323a7c0e28'
[ 22.649298] MODSIGN: Loaded cert 'Synology kernel module signing key: 4646ce54489669338118a3b1286da156ac366fa5'
[ 22.688298] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 22.713836] MTT: registering output driver dfs
[ 22.718314] MTT: multicore-trace initialized.
[ 22.722706] vmmc0: disabling
[ 22.725585] regulator-dummy: disabling
[ 22.763864] Freeing unused kernel memory: 232K (80666000 - 806a0000)
[ 22.874791] stih407-usb-genphy f8.usbpicophy: STiH407 USB Generic picoPHY driver probed!
[ 22.883326] stih407-usb-genphy fc.usbpicophy: STiH407 USB Generic picoPHY driver probed!
[ 22.891867] stih407-usb-genphy 100.usbpicophy: STiH407 USB Generic picoPHY driver probed!
[ 22.923340] sti-usb3-phy 8f90000.usb3_phy: USB3 MiPHY Ref clk 30 MHz enabled
[ 22.930486] sti-usb3-phy 8f90000.usb3_phy: usb3 ioaddr 0x9d974000, pipew ioaddr 0x9d976000
[ 22.939063] sti-usb3-phy 8f90000.usb3_phy: USB3 MiPHY2 probed
[ 23.002514] usbcore: registered new interface driver usbfs
[ 23.010073] usbcore: registered new interface driver hub
[ 23.018321] usbcore: registered new device driver usb
[ 23.076151] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 23.097030] ehci-pci: EHCI PCI platform driver
[ 23.123070] ehci-platform: EHCI generic platform driver
[ 23.151531] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 23.223460] st-pinctrl 922f080.pin-controller-rear: maps: function usb0 group usb2-0 num 3
[ 23.231808] st-hcd 9a03c00.usb: 48MHz ohci clk not found
[ 23.237241] stih407-usb-genphy f8.usbpicophy: Generic picoPHY usb port init.
[ 23.244328] stih407-usb-genphy f8.usbpicophy: found picoPHY in rst state
[ 23.251390] ehci-platform ehci-platform.0: EHCI Host Controller
[ 23.257320] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 23.266010] ehci-platform ehci-platform.0: irq 183, io mem 0x09a03e00
[ 23.287964] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 23.296937] hub 1-0:1.0: USB hub found
[ 23.300721] hub 1-0:1.0: 1 port detected
[ 23.306067] ohci-platform ohci-platform.0: Generic Platform OHCI Controller
[ 23.313080] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2
[ 23.321229] ohci-platform ohci-platform.0: irq 212, io mem 0x09a03c00
[ 23.382793] hub 2-0:1.0: USB hub found
[ 23.386555] hub 2-0:1.0: 1 port detected
[ 23.421155] st-pinctrl 922f080.pin-controller-rear: maps: function usb3 group usb3-2 num 3
[ 23.429581] usb-st-dwc3 8f94000.dwc3: glue-logic addr 0x9da4c000, syscfg-reg offset 0x110
[ 23.438612] dwc3 9900000.dwc3: unable to find phy
[ 23.445418] sti-usb3-phy 8f90000.usb3_phy: MiPHY28LP setup
[ 23.451012] sti-usb3-phy 8f90000.usb3_phy: MiPHY28LP release 0x231 found
[ 23.457911] sti-usb3-phy 8f90000.usb3_phy: USB3 MIPHY28LP timer initialized
[ 23.464907] stih407-usb-genphy 100.usbpicophy: Generic picoPHY usb port init.
[ 23.671893] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 23.677378] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 3
[ 23.685899] xhci-hcd xhci-hcd.0.auto: irq 187, io mem 0x09900000
[ 23.692404] xHCI xhci_add_endpoint called for root hub
[ 23.692415] xHCI xhci_check_bandwidth called for root hub
[ 23.694110] hub 3-0:1.0: USB hub found
[ 23.697873] hub 3-0:1.0: 1 port detected
[ 23.702009] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 23.707498] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 4
[ 23.715842] xHCI xhci_add_endpoint called for root hub
[ 23.715852] xHCI xhci_check_bandwidth called for root hub
[ 23.717932] hub 4-0:1.0: USB hub found
[ 23.721751] hub 4-0:1.0: 1 port detected
[ 23.725841] usb-st-dwc3 8f94000.dwc3: configured as host DRD
[ 23.731620] usb-st-dwc3 8f94000.dwc3: probe exits fine...
[ 23.798394] ds216play_synobios: module license 'Synology Inc.' taints kernel.
[ 23.806597] Disabling lock debugging due to kernel taint
[ 23.813289] correction with 0x00
[ 23.814383] 2020-1-18 15:31:0 UTC
[ 23.814393] synobios: load, major number 201
[ 23.818716] Brand: Synology
[ 23.818723] Model: DS-216play
[ 23.818730] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 23.818746] synobios cpu_arch proc entry initialized
[ 23.823702] synobios crypto_hw proc entry initialized
[ 23.828766] synobios syno_platform proc entry initialized
[ 23.834391] synobios open /dev/ttyS1 success
[ 23.852651] synobios: unload
[ 23.871594] md: Autodetecting RAID arrays.
[ 23.921085] md: invalid raid superblock magic on sda5
[ 23.926129] md: sda5 does not have a valid v0.90 superblock, not importing!
[ 23.970550] md: invalid raid superblock magic on sdb5
[ 23.975590] md: sdb5 does not have a valid v0.90 superblock, not importing!
[ 23.982560] md: Scanned 6 and added 4 devices.
[ 23.986988] md: autorun ...
[ 23.989778] md: considering sda1 ...
[ 23.993349] md: adding sda1 ...
[ 23.996570] md: sda2 has different UUID to sda1
[ 24.001107] md: adding sdb1 ...
[ 24.004325] md: sdb2 has different UUID to sda1
[ 24.008870] md: created md0
[ 24.011649] md: bind
[ 24.014372] md: bind
[ 24.017083] md: running:
[ 24.021096] md/raid1:md0: active with 2 out of 2 mirrors
[ 24.071135] md0: detected capacity change from 0 to 2549940224
[ 24.077176] md: considering sda2 ...
[ 24.080787] md: adding sda2 ...
[ 24.084024] md: adding sdb2 ...
[ 24.089967] md: created md1
[ 24.092761] md: bind
[ 24.095493] md: bind
[ 24.098247] md: running:
[ 24.104109] md/raid1:md1: active with 2 out of 2 mirrors
[ 24.132308] md1: detected capacity change from 0 to 2147418112
[ 24.138385] md: ... autorun DONE.
[ 24.175960] md0: unknown partition table
[ 24.357985] usb 2-1: new full-speed USB device number 2 using ohci-platform
[ 25.777976] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 25.894016] EXT4-fs (md0): barriers disabled
[ 25.911464] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts:
[ 25.948034] usb 3-1: not running at top speed
[ 26.397983] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 26.404519] xhci-hcd xhci-hcd.0.auto: Setup ERROR: address device command for slot 1.
[ 27.567962] usb 3-1: new high-speed USB device number 3 using xhci-hcd
[ 27.738005] usb 3-1: not running at top speed
[ 28.187990] usb 3-1: new high-speed USB device number 3 using xhci-hcd
[ 28.194528] xhci-hcd xhci-hcd.0.auto: Setup ERROR: address device command for slot 1.
[ 29.357963] usb 3-1: new high-speed USB device number 4 using xhci-hcd
[ 29.378054] usb 3-1: not running at top speed
[ 29.827975] usb 3-1: new high-speed USB device number 4 using xhci-hcd
[ 29.848044] usb 3-1: not running at top speed
[ 30.297977] usb 3-1: new high-speed USB device number 4 using xhci-hcd
[ 30.318044] usb 3-1: not running at top speed
[ 30.767975] usb 3-1: new high-speed USB device number 4 using xhci-hcd
[ 30.788040] usb 3-1: not running at top speed
[ 31.237976] usb 3-1: new high-speed USB device number 4 using xhci-hcd
[ 31.258041] usb 3-1: not running at top speed
[ 31.707975] usb 3-1: new high-speed USB device number 4 using xhci-hcd
[ 31.728043] usb 3-1: not running at top speed
[ 31.898245] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: barrier=1
[ 33.018738] EXT4-fs (md0): re-mounted. Opts: (null)
[ 38.481537] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 38.486988] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 38.955872] md1: unknown partition table
[ 39.113074] Adding 2097084k swap on /dev/md1. Priority:-1 extents:1 across:2097084k
[ 42.277100] NET: Registered protocol family 10
[ 42.331217] sit: IPv6 over IPv4 tunneling driver
[ 42.862884] init: syno-auth-check main process (2829) killed by TERM signal
[ 44.198158] fuse init (API version 7.22)
[ 44.322488] Loading modules backported from Linux version v3.18.1-0-g39ca484
[ 44.329581] Backport generated by backports.git v3.18.1-1-0-g5e9ec4c
[ 44.369163] systemd-udevd[3197]: starting version 204
[ 44.778216] exFAT: Version 1.2.9
[ 45.782515] correction with 0x00
[ 45.786638] 2020-1-18 15:31:22 UTC
[ 45.786653] synobios: load, major number 201
[ 45.791018] Brand: Synology
[ 45.791031] Model: DS-216play
[ 45.791042] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 45.791072] synobios cpu_arch proc entry initialized
[ 45.796031] synobios crypto_hw proc entry initialized
[ 45.801201] synobios syno_platform proc entry initialized
[ 45.806895] synobios open /dev/ttyS1 success
[ 49.260368] dwmac1000: Master AXI performs any burst length
[ 49.266296] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 49.399534] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 49.477352] nf_conntrack version 0.5.0 (6470 buckets, 25880 max)
[ 49.814913] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 53.336120] md: md2 stopped.
[ 53.341199] md: bind
[ 53.349069] md: bind
[ 53.385547] md/raid1:md2: active with 2 out of 2 mirrors
[ 53.410574] md2: detected capacity change from 0 to 1995451858944
[ 53.428986] md2: unknown partition table
[ 53.802554] bio: create slab at 1
[ 55.259173] libphy: stmmac-0:01 - Link is Up - 1000/Full
[ 55.266261] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 55.424446] EXT4-fs (dm-0): barriers disabled
[ 55.539405] EXT4-fs (dm-0): mounted filesystem with writeback data mode. Opts: usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,synoacl,data=writeback,oldalloc
[ 64.046672] usbcore: registered new interface driver usb-storage
[ 64.166270] usbcore: registered new interface driver usblp
[ 64.492951] usbcore: registered new interface driver usbhid
[ 64.498562] usbhid: USB HID core driver
[ 67.453235] iSCSI:target_core_rodsp_server.c:1027:rodsp_server_init RODSP server started, login_key(00113274eac5).
[ 67.701832] iSCSI:extent_pool.c:766:ep_init syno_extent_pool successfully initialized
[ 68.163436] iSCSI:target_core_device.c:617:se_dev_align_max_sectors Rounding down aligned max_sectors from 4294967295 to 4294967288
[ 68.188492] iSCSI:target_core_lunbackup.c:361:init_io_buffer_head 512 buffers allocated, total 2097152 bytes successfully
[ 68.475261] iSCSI:target_core_file.c:146:fd_attach_hba RODSP plugin for fileio is enabled.
[ 68.483577] iSCSI:target_core_file.c:153:fd_attach_hba ODX Token Manager is enabled.
[ 68.508082] iSCSI:target_core_multi_file.c:91:fd_attach_hba RODSP plugin for multifile is enabled.
[ 68.517097] iSCSI:target_core_ep.c:813:ep_attach_hba RODSP plugin for epio is enabled.
[ 68.525061] iSCSI:target_core_ep.c:820:ep_attach_hba ODX Token Manager is enabled.
[ 70.135951] ICS Version 1.0.2 : Final (05:06:18 May 10 2019)
[ 70.135966] ICS init 1 debug_flags 0x4ffffffff debug_chan 0x1 connect 0 watchdog 0 bpa2_part 'multicom'
[ 70.135970] stih41x_configure_clocks_ics() : start
[ 70.135977] clock lock 966815d4
[ 70.135995] clk : clk_00 9b824580 taken
[ 70.136005] clk : clk_01 9b824600 taken
[ 70.136015] clk : clk_02 9b824500 taken
[ 70.136023] clk : clk_03 9b824500 taken
[ 70.136039] prepare all clocks
[ 70.136048] stih41x_configure_clocks_ics() : exit
[ 70.136066] ICS loading firmware 'vid_firmware-mpeg4p2-stih407.elf' cpu 2 (video)
[ 70.200642] ICS starting cpu 2 (video) entry 0x41c00400
[ 70.200652] enable clock 1
[ 70.200667] ICS loading firmware 'audio_firmware-profile0-stih407.elf' cpu 3 (audio)
[ 70.265737] ICS starting cpu 3 (audio) entry 0x40c00c00
[ 70.265748] enable clock 2
[ 70.265761] ICS loading firmware 'audio_firmware-profile0-stih407.audio1.elf' cpu 1 (gp1)
[ 70.296634] ICS starting cpu 1 (gp1) entry 0x41400c00
[ 70.296645] enable clock 0
[ 70.296657] ICS loading firmware 'security_firmware-stih410.elf' cpu 4 (gp0)
[ 70.316943] ICS starting cpu 4 (gp0) entry 0x40400300
[ 70.316955] enable clock 3
[ 70.316967] ICS: Using BPA2 partition 'multicom'
[ 70.316973] Test: ICS_GetTuneable(ICS_TUNEABLE_ADMIN_THREAD_PRIORITY) = -90 Calling ICS_cpu_init(0, 0x1f, 0x0)
[ 70.316986] insmod:ics_cpu_init:346 cpuNum 0 cpuMask 0x1f flags 0x0
[ 70.317090] insmod:ics_cpu_init:384 cpu 0 ('host') cpuMask 0x1f ics_state 97bba000
[ 70.319791] insmod:ics_cpu_init:550 Memory usage : allocated 0 OS used 0 (+0) avail 0
[ 70.319801] ICS Adding region[0] 0x60000000 0x800000 cacheflag=0x1
[ 70.326520] ICS debug: 96681000 in module_dir
[ 70.576324] MME Version 4.4.1 Final (05:06:30 May 10 2019)
[ 70.576335] MME module init=1 debug_flags=0x1 pool_size=262144
[ 70.581080] insmod:mme_init:373 Succeeded on cpu 0 mme_state 99d24e00
[ 70.581089] insmod:mme_init:377 Memory usage : OS used 0 (+0) avail 0
[ 70.666614] Load module infra_main [?] by insmod (pid 8069)
[ 70.930692] Load module stm_event_main [?] by insmod (pid 8081)
[ 71.155604] stm-ce cesc.54: Enabling clock stfe_ccsc
[ 71.160604] stm-ce cesc.54: Clock stfe_ccsc @ 225000068Hz
[ 71.165997] stm-ce cesc.54: Enabling clock CLK_TP
[ 71.170741] stm-ce cesc.54: Clock CLK_TP @ 400000000Hz
[ 71.176254] stm-ce cesc.54: Disabling clock stfe_ccsc
[ 71.181370] stm-ce cesc.54: Disabling clock CLK_TP
[ 71.199230] st_relay_core_open done ok 786432x10
[ 71.254722] st_relayfs_open done ok
[ 71.293875] Init of MME log wrapper
[ 71.297360] acc_mme_loginit done ok
[ 71.468836] bdispII_device_features.c:409: BDisp/BLT: blitter is a 'STiH407' (15)
[ 71.588180] bdispII.c:183: AQ(bdisp-aq2) not found
[ 71.592971] bdispII.c:183: AQ(bdisp-aq3) not found
[ 71.597756] bdispII.c:183: AQ(bdisp-aq4) not found
[ 71.602762] bdispII_device_features.c:409: BDisp/BLT: blitter is a 'STiH407' (15)
[ 71.641126] bdispII.c:183: AQ(bdisp-aq2) not found
[ 71.646173] bdispII.c:183: AQ(bdisp-aq3) not found
[ 71.651011] bdispII.c:183: AQ(bdisp-aq4) not found
[ 71.717903] Loading os wrapper module...
[ 71.792485] Loading stmfe utility module ...
[ 71.970159] Loading module stm_fe ...
[ 71.974066] st-pinctrl 920f080.pin-controller-front0: maps: function tsin0 group tsin0_serial num 6
[ 71.983217] stm_demod_get_pdata: No syscfg phandle specified
[ 71.988930] demod_config_pdata: demod config not set properly
[ 71.994742] st-pinctrl 920f080.pin-controller-front0: maps: function tsin4 group tsin4_serial_alt3 num 6
[ 72.004373] stm_demod_get_pdata: ts mapping control syscfg update ok
[ 72.010787] demod_config_pdata: demod config not set properly
[ 72.016604] st-pinctrl 920f080.pin-controller-front0: maps: function tsin3 group tsin3_serial num 6
[ 72.025768] stm_demod_get_pdata: No syscfg phandle specified
[ 72.031503] demod_config_pdata: demod config not set properly
[ 72.037622] stm_lnb_get_pdata: lnb config not properly set
[ 72.043231] stm_lnb_get_pdata: lnb config not properly set
[ 72.049116] stm_fe_diseqc_probe: Config diseqc stm_fe_diseqc.0
[ 72.055020] stm_fe_diseqc_probe: Config diseqc stm_fe_diseqc.1
[ 72.061342] stm_fe_ip_probe: Configuring ip stm_fe_ip.0
[ 72.066630] stm_fe_ip_probe: Configuring ip stm_fe_ip.1
[ 72.071951] stm_fe_ip_probe: Configuring ip stm_fe_ip.2
[ 72.077233] stm_fe_ip_probe: Configuring ip stm_fe_ip.3
[ 72.082578] stm_fe_ip_probe: Configuring ip stm_fe_ip.4
[ 72.087858] stm_fe_ip_probe: Configuring ip stm_fe_ip.5
[ 72.571346] st-fdma 8e20000.fdma-mpe: Requesting firmware: fdma_STiH407_0.elf
[ 72.601699] st-fdma 8e20000.fdma-mpe: SLIM hw 0.134413, FDMA fw 1.0
[ 72.619749] platform denc.fw: requesting frm: 'denc.fw', 7f303910/99177c0c
[ 72.626637] platform denc.fw: using denc_H407_b2120.fw for denc.fw firmware
[ 72.651741] platform denc.fw: loading firmware data.
[ 72.656707] platform denc.fw: firmware data is loaded (size=40).
[ 72.662849] platform denc.fw: frm 'denc.fw' successfully loaded
[ 72.669050] platform hdf.fw: requesting frm: 'hdf.fw', 7f303910/99f3044c
[ 72.675766] platform hdf.fw: using hdf_H407_b2120.fw for hdf.fw firmware
[ 72.718054] platform hdf.fw: loading firmware data.
[ 72.722939] platform hdf.fw: firmware data is loaded (size=264).
[ 72.729027] platform hdf.fw: frm 'hdf.fw' successfully loaded
[ 72.745570] stm-ios: vibe_os_clk_disable: Clock already disable CLK_PIX_HDMI
[ 72.752707] stm-ios: vibe_os_clk_disable: Clock already disable CLK_REF_HDMIPHY
[ 72.760103] stm-ios: vibe_os_clk_disable: Clock already disable CLK_TMDS_HDMI
[ 72.767324] stm-ios: vibe_os_clk_disable: Clock already disable CLK_PIX_MAIN_DISP
[ 72.774941] stm-ios: vibe_os_clk_disable: Clock already disable CLK_PIX_MAIN_DISP
[ 72.782534] stm-ios: vibe_os_clk_disable: Clock already disable CLK_TMDS_HDMI
[ 72.789772] stm-ios: vibe_os_clk_disable: Clock already disable CLK_PIX_HDMI
[ 72.796912] stm-ios: vibe_os_clk_disable: Clock already disable CLK_REF_HDMIPHY
[ 72.981944] stm-ios: vibe_os_clk_disable: Clock already disable CLK_PIX_HDMI
[ 72.989080] stm-ios: vibe_os_clk_disable: Clock already disable CLK_REF_HDMIPHY
[ 72.996474] stm-ios: vibe_os_clk_disable: Clock already disable CLK_TMDS_HDMI
[ 73.003696] stm-ios: vibe_os_clk_disable: Clock already disable CLK_PIX_MAIN_DISP
[ 74.147926] stm_display_plane_is_feature_applicable V4L2_CID_STM_IQI_EXT_PEAKING_PRESET = -95
[ 74.148161] stm_display_plane_is_feature_applicable V4L2_CID_STM_IQI_EXT_PEAKING_PRESET = -95
[ 74.148351] stm_display_plane_is_feature_applicable V4L2_CID_STM_IQI_EXT_PEAKING_PRESET = -95
[ 74.148539] stm_display_plane_is_feature_applicable V4L2_CID_STM_IQI_EXT_PEAKING_PRESET = -95
[ 74.148723] stm_display_plane_is_feature_applicable V4L2_CID_STM_IQI_EXT_PEAKING_PRESET = -95
[ 74.148915] stm_display_plane_is_feature_applicable V4L2_CID_STM_IQI_EXT_PEAKING_PRESET = 0
[ 74.149116] stm_display_plane_is_feature_applicable V4L2_CID_STM_IQI_EXT_PEAKING_PRESET = -95
[ 74.149224] stmvout_probe_media_planes: Display 0 found 7 planes (skipped 0)
[ 74.156415] stmvout_probe_media_outputs: Display 0: 4 output Plug added
[ 74.258059] stm-ios: vibe_os_clk_disable: Clock already disable CLK_PIX_HDMI
[ 74.265203] stm-ios: vibe_os_clk_disable: Clock already disable CLK_REF_HDMIPHY
[ 74.272590] stm-ios: vibe_os_clk_disable: Clock already disable CLK_TMDS_HDMI
[ 74.279808] stm-ios: vibe_os_clk_disable: Clock already disable CLK_PIX_MAIN_DISP
[ 76.571473] SE-Aud-CtoP pol:2 prio:58
[ 76.575127] SE-Aud-PtoD pol:2 prio:58
[ 76.578812] SE-Aud-DtoM pol:2 prio:60
[ 76.582470] SE-Aud-MPost pol:2 prio:62
[ 76.586212] SE-Vid-CtoP pol:2 prio:58
[ 76.589898] SE-Vid-PtoD pol:2 prio:58
[ 76.593555] SE-Vid-DtoM pol:2 prio:60
[ 76.597215] SE-Vid-MPost pol:2 prio:62
[ 76.600994] SE-Vid-H264Int pol:2 prio:59
[ 76.604905] SE-Vid-HevcInt pol:2 prio:59
[ 76.608846] SE-Aud-Reader pol:2 prio:64
[ 76.612680] SE-Aud-StreamT pol:2 prio:59
[ 76.616598] SE-Aud-Mixer pol:2 prio:64
[ 76.620372] SE-Aud-BcstMix pol:2 prio:64
[ 76.624290] SE-Aud-Bypass pol:2 prio:64
[ 76.628141] SE-Man-Coord pol:2 prio:59
[ 76.631885] SE-Man-BrSrcGrab pol:2 prio:50
[ 76.635974] SE-Man-BrCapture pol:2 prio:50
[ 76.640087] SE-Man-DsVideo pol:2 prio:74
[ 76.643998] SE-Playbck-Drain pol:2 prio:64
[ 76.648103] SE-EncAud-ItoP pol:2 prio:61
[ 76.652017] SE-EncAud-PtoC pol:2 prio:58
[ 76.655926] SE-EncAud-CtoO pol:2 prio:59
[ 76.659875] SE-EncVid-ItoP pol:2 prio:61
[ 76.664219] SE-EncVid-PtoC pol:2 prio:58
[ 76.668360] SE-EncVid-CtoO pol:2 prio:59
[ 76.672281] SE-Encod-Coord pol:2 prio:61
[ 76.676198] SE-Other pol:2 prio:50
[ 76.681365] player2 probe done ok
[ 76.684955] [sched_delayed] sched: RT throttling activated
[ 76.952210] stm_te_tsmux_mme.te_tsmux_mme_init_module() - Load module te_tsmux_mme by insmod (pid 8521)
[ 77.125334] ata1.00: configured for UDMA/133
[ 77.129682] ata1: EH complete
[ 77.592462] ata2.00: configured for UDMA/133
[ 77.596742] ata2: EH complete
[ 80.670883] stm_te_hal.stpti_tp_probe() - Probed 8880000.tetp device
[ 80.677377] stm_te_hal.stpti_tp_probe() - Caching firmware pti_tp3.elf
[ 80.695507] stm_te_hal.stptiHAL_pDeviceInit() - Clocks Per Second = 100.
[ 80.702265] stm-tango-tp 8880000.tetp: Resource tp [0x8880000:0x88aefff]
[ 80.709271] stm_te_hal.stptiHAL_pDeviceInit() - TANGO TP mapped... [ 08880000 => 9de40000 ]
[ 80.717625] stm-tango-tp 8880000.tetp: Enabling clock CLK_TP
[ 80.723318] stm-tango-tp 8880000.tetp: Clock CLK_TP @ 400000000Hz
[ 80.729475] stm-tango-tp 8880000.tetp: IRQ 57
[ 80.733877] stm_te_hal.stptiHAL_pDeviceInit() - TP ISR installed on number 0x00000039.
[ 80.741815] stm-tango-tp 8880000.tetp: Loading firmware: pti_tp3.elf
[ 80.748216] stm-tango-tp 8880000.tetp: Loading segment 0 0x00000000 (0x1a8 bytes) -> 0x9de40000 (0x11b0 bytes)
[ 80.758518] stm-tango-tp 8880000.tetp: Loading segment 1 0x000011b0 (0xe4f8 bytes) -> 0x9de411b0 (0xe528 bytes)
[ 80.777930] stm-tango-tp 8880000.tetp: Loading segment 2 0x00400000 (0x9f38 bytes) -> 0x9de50000 (0x9f38 bytes)
[ 80.794440] stm_te_hal.stptiHAL_pDeviceInit() - TP Firmware loaded successfully
[ 80.801767] stm_te_hal.stptiHAL_pDeviceInit() - Started TP from reset (waiting for Ready)
[ 80.810029] stm_te_hal.stptiHAL_TPInterruptHandler() - STxP70_TP0 : Starting 01022501_TP_VERSION [CS00029AA8] Built 10:08:55 Sep 4 2014
[ 80.822332] stm_te_hal.stptiHAL_pDeviceSetInitialisationParameters() - Assuming STTKD driver in system.
[ 80.831942] stm_te_hal.stptiHAL_TPInterruptHandler() - STxP70_TP0 : Total Usage 39688 of 44032 bytes.
[ 80.841269] stm_te_hal.stptiHAL_TPInterruptHandler() - STxP70_TP0 : Configuring Timer Counter for packet timestamps. Divider 0xB

[ 80.868272] stm_te_hal.stptiHAL_pDeviceInit() - TP (device0) Started Successfully.
[ 80.875893] stm_te_hal.stptiHAL_pDeviceInit() - Across 8 vDevices, there are 256 slots, 96 buffers, 32 indexers, 256 hw section filters.
[ 80.920267] stm_te_hal.stptiHAL_pDeviceSleep() - TP sleeping (device0)
[ 80.926904] stm-tango-tp 8880000.tetp: Disabling clock CLK_TP
[ 80.954504] stm_te_hal.stpti_stfe_probe() - Probed 8a20000.tefe device
[ 80.961302] stm_te_hal.stpti_stfe_probe() - Caching firmware pti_memdma_h407.elf
[ 80.969070] stm_te_hal.stptiHAL_EventTask() - Entering Event Task for 1ff07fff
[ 80.976425] stm_te_hal.tango_idle() - pDevice idle
[ 80.981347] stm_te_hal.tango_suspend() - pDevice 0 suspended
[ 80.987130] stm-tango-tp 8880000.tetp: Enabling clock CLK_TP
[ 80.992884] stm-tango-tp 8880000.tetp: Clock CLK_TP @ 400000000Hz
[ 80.999128] stm_te_hal.stptiHAL_pDeviceWakeup() - TP woken up (device0)
[ 81.005745] stm_te_hal.stptiHAL_pDevicePowerdown() - TP held in reset (device0)
[ 81.013106] stm_te_hal.stptiHAL_pDevicePowerdown() - Saving TP shared memory (device0)
[ 81.024861] stm_te_hal.stptiHAL_pDevicePowerdown() - TP powered down (device0)
[ 81.032104] stm-tango-tp 8880000.tetp: Disabling clock CLK_TP
[ 81.037873] stm_te_hal.tango_suspend() - pDevice 0 frozen
[ 81.082410] stm_te_hal.stptiTSHAL_Init() - Initialising STFE device 8a20000.tefe

[ 81.091370] stm-tango-stfe 8a20000.tefe: Resource stfe [0x8a20000:0x8a2ffff]
[ 81.098530] stm-tango-stfe 8a20000.tefe: Resource stfe-ram [0x8a00000:0x8a03fff]
[ 81.105948] stm-tango-stfe 8a20000.tefe: Idle IRQ 67
[ 81.110942] stm-tango-stfe 8a20000.tefe: error IRQ 66
[ 81.115992] stm-tango-stfe 8a20000.tefe: Enabling clock stfe_ccsc
[ 81.122109] stm-tango-stfe 8a20000.tefe: Clock stfe_ccsc @ 225000068Hz
[ 81.128745] stm-tango-stfe 8a20000.tefe: Enabling clock stfe_frc-0
[ 81.135001] stm-tango-stfe 8a20000.tefe: Setting clock stfe_frc-0 to 27000000Hz
[ 81.142376] stm-tango-stfe 8a20000.tefe: Clock stfe_frc-0 @ 27000001Hz
[ 81.148976] stm-tango-stfe 8a20000.tefe: Loading firmware: pti_memdma_h407.elf
[ 81.156962] stm-tango-stfe 8a20000.tefe: Loading IMEM segment 0 0x00000000 (0x39f bytes) -> 0x9da48000 (0x4d4 bytes)
[ 81.167866] stm-tango-stfe 8a20000.tefe: Loading DMEM segment 1 0x00000020 (0x5c bytes) -> 0x9da3a080 (0x5c bytes)
[ 81.178328] stm-tango-stfe 8a20000.tefe: Loading DMEM segment 2 0x00000037 (0x0 bytes) -> 0x9da3a0dc (0xc0 bytes)
[ 81.188619] stm-tango-stfe 8a20000.tefe: Loading DMEM segment 3 0x00000010 (0x14 bytes) -> 0x9da3a040 (0x14 bytes)
[ 81.199030] stm-tango-stfe 8a20000.tefe: Loading DMEM segment 4 0x00000000 (0x18 bytes) -> 0x9da3a000 (0x18 bytes)
[ 81.209508] stm-tango-stfe 8a20000.tefe: Loading DMEM segment 5 0x000000a0 (0x2e0 bytes) -> 0x9da3a280 (0x2e0 bytes)
[ 81.220113] stm-tango-stfe 8a20000.tefe: Loading DMEM segment 6 0x00000080 (0x5c bytes) -> 0x9da3a200 (0x5c bytes)
[ 81.230548] stm-tango-stfe 8a20000.tefe: Loading DMEM segment 7 0x00000160 (0x200 bytes) -> 0x9da3a580 (0x200 bytes)
[ 81.241169] stm_te_hal.stptiTSHAL_Stfev2_CreateConfig() - THIS IS THE RIGHT MEMDMA FW
[ 81.249011] stm_te_hal.stptiTSHAL_Stfev2_CreateConfig() - THERE ARE 23 MEMDMA CH and 1 TP
[ 81.257489] stm_te_hal.stptiTSHAL_Stfev2_MemdmaInit() - MEMDMA ISR installed on number 0x00000043.
[ 81.266566] stm_te_hal.stptiTSHAL_Stfev2_SystemInit() - ERROR TSIN ISR error installed on number 0x00000042.
[ 81.278975] stm_te_hal.stfe_idle() - stfe idle
[ 81.283614] stm_te_hal.stptiTSHAL_Stfev2_SystemTerm() - ERROR TSIN ISR error uninstalled on number 0x00000042.
[ 81.293648] stm_te_hal.stptiTSHAL_Stfev2_MemdmaTerm() - MEMDMA ISR uninstalled on number 0x00000043.
[ 81.302838] stm-tango-stfe 8a20000.tefe: Disabling clock stfe_ccsc
[ 81.309408] stm-tango-stfe 8a20000.tefe: Disabling clock stfe_tsout-0
[ 81.315845] stm-tango-stfe 8a20000.tefe: Disabling clock stfe_tsout-1
[ 81.322437] stm-tango-stfe 8a20000.tefe: Disabling clock stfe_frc-0
[ 81.328810] stm-tango-stfe 8a20000.tefe: Disabling clock stfe_frc-1
[ 81.335506] stm-tango-stfe 8a20000.tefe: Disabling clock stfe_mchi
[ 81.341725] stm_te_hal.stfe_suspend() - Suspend TSInput 0
[ 81.347189] stm_te_hal.stfe_suspend() - Powered-down TSInput -1
[ 82.472507] Loading sat tuner wrapper module ...
[ 82.582568] Loading VGLNA module ...
[ 82.704572] Loading t/c tuner wrapper module ...
[ 82.835570] Loading FE IP driver module...
[ 82.935944] Loading stv4100 tuner module...
[ 83.096299] Loading stv0367 driver module...
[ 83.198959] Loading stv6120 tuner module ...
[ 83.323995] Loading stv0910 driver module...
[ 83.829626] Loading module ctrl_via_stm_fe = -1
[ 83.834153] stm_fe_discover: Discovered stm_fe_diseqc.0 ...
[ 83.839741] stm_fe_discover: Discovered stm_fe_diseqc.1 ...
[ 83.845307] stm_fe_discover: Discovered stm_fe_ip.0 ...
[ 83.850526] stm_fe_discover: Discovered stm_fe_ip.1 ...
[ 83.855737] stm_fe_discover: Discovered stm_fe_ip.2 ...
[ 83.860955] stm_fe_discover: Discovered stm_fe_ip.3 ...
[ 83.866165] stm_fe_discover: Discovered stm_fe_ip.4 ...
[ 83.871382] stm_fe_discover: Discovered stm_fe_ip.5 ...
[ 83.876592] 8 stm_fe objects discovered
[ 83.880419] DVB: registering new adapter (ST DVB frontend driver)
[ 83.886756] demod_config_pdata: demod config not set properly
[ 83.892548] demod_config_pdata: demod config not set properly
[ 83.898369] demod_config_pdata: demod config not set properly
[ 83.904355] stm_dvb_get_lnb_pdata: lnb config not properly set
[ 83.910296] stm_dvb_get_lnb_pdata: lnb config not properly set
[ 83.916452] stm_dvb_diseqc_attach() Invalid demod object, cannot attach diseqc
[ 83.923749] stm_dvb_diseqc_attach() Invalid demod object, cannot attach diseqc
[ 83.931450] Configuring ip IPFE-STM_FE IP name stm-dvb-ip.37
[ 83.939611] Configuring ip IPFE-STM_FE IP name stm-dvb-ip.40
[ 83.946658] Configuring ip IPFE-STM_FE IP name stm-dvb-ip.43
[ 83.978396] Configuring ip IPFE-STM_FE IP name stm-dvb-ip.46
[ 83.986432] Configuring ip IPFE-STM_FE IP name stm-dvb-ip.49
[ 83.998316] Configuring ip IPFE-STM_FE IP name stm-dvb-ip.52
[ 84.008712] Created stm_fe_ip.0 for parent stm_fe_ip.0
[ 84.016229] Created stm_fe_ip.1 for parent stm_fe_ip.1
[ 84.029267] Created stm_fe_ip.2 for parent stm_fe_ip.2
[ 84.048067] Created stm_fe_ip.3 for parent stm_fe_ip.3
[ 84.055025] Created stm_fe_ip.4 for parent stm_fe_ip.4
[ 84.068077] Created stm_fe_ip.5 for parent stm_fe_ip.5
[ 84.074786] Found 8 demuxes, 256 pid filters, 96 output filters
[ 84.083678] Added device stm_dvb_demux.0
[ 84.091181] Added device stm_dvb_demux.1
[ 84.096512] Added device stm_dvb_demux.2
[ 84.111054] Added device stm_dvb_demux.3
[ 84.122066] Added device stm_dvb_demux.4
[ 84.128397] Added device stm_dvb_demux.5
[ 84.156593] Added device stm_dvb_demux.6
[ 84.165264] Added device stm_dvb_demux.7
[ 84.271685] HevcppProbe SE-Vid-Hevcpp pol:2 prio:50
[ 84.276563] HevcppProbe hw core nb: 1
[ 84.280279] ret value : 0x0 max frequency value : 240000000
[ 84.285920] OSDEV_LinkDevice /dev/hevcpp - Major 247, Minor 0
[ 84.291687] Hevcpp probe done ok
[ 84.888144] compo_capture_subdev_init(): created disabled links to video plane
[ 84.895364] compo_capture_subdev_init(): created disabled links to gfx plane
[ 84.902416] compo_capture_subdev_init(): created disabled links to output
[ 84.990463] OSDEV_LinkDevice /dev/allocator - Major 245, Minor 0
[ 84.996463] AllocatorLoadModule done ok
[ 85.077229] h264encoder 8c85000.h264encoder: Hva registers base address is 0x8c85000 and size is 0xfff
[ 85.086646] h264encoder 8c85000.h264encoder: Hva esram base address is 0x6000000 and size is 0x3ffff
[ 85.095862] h264encoder 8c85000.h264encoder: Hva interrupt number is 90
[ 85.102858] h264encoder 8c85000.h264encoder: Hva error interrupt number is 91
[ 85.110121] h264encoder 8c85000.h264encoder: Hva clock set to 300000000
[ 85.116950] h264encoder 8c85000.h264encoder: Hva version is 0x400
[ 85.124154] h264encoder 8c85000.h264encoder: (StreamId:0x0) Unable to soft-reset hva => reset platform
[ 85.134456] h264encoder 8c85000.h264encoder: (StreamId:0x0) Incorrect stbus plug configuration, StBusPlugConfig = 0x0
[ 85.145067] h264encoder 8c85000.h264encoder: (StreamId:0x0) Force stbus plug configuration to recommended value, StBusPlugConfig = 0x408081
[ 85.158070] h264encoder 8c85000.h264encoder: (StreamId:0x0) Reset hva and configure registers done
[ 85.167076] h264encoder 8c85000.h264encoder: Setting hva max instance number to 30
[ 85.174783] h264encoder 8c85000.h264encoder: H264 encode hardware host transformer probe done ok
[ 85.311594] H264ppProbe SE-Vid-H264pp pol:2 prio:50
[ 85.316614] H264pp: hw core nb: 1
[ 85.320298] ret value : 0x0 max frequency value : 266250000
[ 85.326006] OSDEV_LinkDevice /dev/h264pp - Major 246, Minor 0
[ 85.331793] h264pp probe done ok
[ 85.447775] HadesProbe: Probing device with DT
[ 85.452287] For CLK_HWPE_HADES ret value : 0x0 max frequency value : 400000000
[ 85.459568] For CLK_FC_HADES ret value : 0x0 max frequency value : 332999958
[ 85.487393] HadesPmRuntime: Resume ..
[ 85.491126] STHORM: library initialization(regs 0a010000(7274496), IRQ 107, partition hades-l3
[ 85.500022] RAB SLAVE: CONF_FC: source 0a100000 (00100000) dest 50000000 size 00080000
[ 85.508492] RAB SLAVE: CL_PERIPH: source 0a200000 (00200000) dest 20000000 size 00080000
[ 85.516735] RAB SLAVE: CONF_ENCMEM: source 0a280000 (00280000) dest 10000000 size 00040000
[ 85.525196] RAB SLAVE: CL_HWPE_OUT: source 0a2f0000 (002f0000) dest 30000000 size 00008000
[ 85.533625] RAB SLAVE: CL_HWPE_OUT: source 0a2f8000 (002f8000) dest 30000000 size 00008000
[ 85.541975] LoadHadesDevice: Hades API initialized with registers base 0a000000, IRQ base 107, BPA2 partition hades-l3
[ 85.563582] STHORM: firmware program segments loaded at 40a00000 (2097152 bytes)
[ 85.571194] HADES_API: Configuring runtime struct @ 0a100000
[ 85.576847] HADES_API: Specified cluster mask: 0x80000001 for 1 clusters
[ 85.583574] HADES_API: Booting fabric controller (id=4) @ 0xa119000
[ 85.589895] HADES_API: Waiting for boot message from FC ..
[ 85.595422] HADES_API: ... FC has booted
[ 85.599362] HADES_API: Sending first config message to FC, mailbox @ 0a118000
[ 85.606553] HADES_API: P2012 library initialization done
[ 85.611902] LoadHadesDevice: HADES FW name: hades_fw.bin, size: 1247176
[ 85.618575] HADES_API: Configuring static binary
[ 85.623190] HADES_API: HADES_InitTransformer: PedfRT_Descr_p(969f1f40) ->binary.size: 1247176 clusterId: 0x1f
[ 85.633199] HADES_API: HADES_InitTransformer -> pedf_rt (p:0x62430000 v:0x9da22000 size:4)
[ 85.642458] HadesPmRuntime: Suspend ..
[ 85.646268] CRCDriver: major 246, minor 0 to 19
[ 85.650850] Hades HEVC host transformer probe done ok
[ 85.776505] stm-c8jpg 8c84000.c8jpg: found c8jpg device at: 0x08c84000, irq: 88
[ 85.784456] stm-c8jpg 8c84000.c8jpg: decoder successfully probed
[ 85.882206] Maximum vp8 clock frequency not retrieved from DT
[ 85.888082] hx170_check_chip_id: Chip ID: 0x67315058
[ 85.893042] VP8 hardware host transformer probe done ok
[ 86.078054] stm-ios: vibe_os_clk_disable: Clock already disable CLK_PIX_HDMI
[ 86.085189] stm-ios: vibe_os_clk_disable: Clock already disable CLK_REF_HDMIPHY
[ 86.092579] stm-ios: vibe_os_clk_disable: Clock already disable CLK_TMDS_HDMI
[ 86.099794] stm-ios: vibe_os_clk_disable: Clock already disable CLK_PIX_MAIN_DISP
[ 86.642766] warning: nginx' uses 32-bit capabilities (legacy support in use) [ 86.648794] warning: nginx' uses 32-bit capabilities (legacy support in use)
[ 87.665527] loop: module loaded
[ 93.124098] findhostd uses obsolete (PF_INET,SOCK_PACKET)
[ 96.430885] usbcore: registered new interface driver usbserial
[ 96.539746] usbcore: registered new interface driver ftdi_sio
[ 96.545561] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 96.553095] ftdi_sio 2-1:1.0: FTDI USB Serial Device converter detected
[ 96.559855] usb 2-1: Detected FT232RL
[ 96.563517] usb 2-1: Number of endpoints 2
[ 96.567639] usb 2-1: Endpoint 1 MaxPacketSize 64
[ 96.572308] usb 2-1: Endpoint 2 MaxPacketSize 64
[ 96.576925] usb 2-1: Setting MaxPacketSize 64
[ 96.590449] usb 2-1: FTDI USB Serial Device converter now attached to ttyUSB0
[ 96.640831] init: synoscheduler-vmtouch main process (2234) killed by TERM signal
[ 96.656356] cp210x: module verification failed: signature and/or required key missing - tainting kernel
[ 96.666631] usbcore: registered new interface driver cp210x
[ 96.672555] usbserial: USB Serial support registered for cp210x
[ 96.760896] usbcore: registered new interface driver pl2303
[ 96.766517] usbserial: USB Serial support registered for pl2303
[ 96.910133] usbcore: registered new interface driver ch341
[ 96.915779] usbserial: USB Serial support registered for ch341-uart
[ 97.019524] usbcore: registered new interface driver ti_usb_3410_5052
[ 97.026043] usbserial: USB Serial support registered for TI USB 3410 1 port adapter
[ 97.033831] usbserial: USB Serial support registered for TI USB 5052 2 port adapter
[ 104.492836] init: synoscheduler-vmtouch main process (10764) killed by TERM signal
[ 106.119327] init: synoscheduler-vmtouch main process (11349) killed by TERM signal
[ 106.558676] tun: Universal TUN/TAP device driver, 1.6
[ 106.563731] tun: (C) 1999-2004 Max Krasnyansky [email protected]
[ 110.766902] init: pkg-WebStation-userdir main process (11452) terminated with status 1
[ 130.413902] usbcore: registered new interface driver snd-usb-audio
[ 132.401678] usbcore: registered new interface driver snd-usb-hiface
[ 229.787238] init: pkg-WebStation-userdir main process (17016) terminated with status 1
[ 233.381760] init: synocontentextractd main process ended, respawning
[ 777.660904] open mtd (RedBoot Config), process=syno_mem_cfg
[ 777.667101] close mtd (RedBoot Config), process=syno_mem_cfg
[ 777.673434] open mtd (RedBoot Config), process=syno_mem_cfg
[ 777.679397] close mtd (RedBoot Config), process=syno_mem_cfg

Output of lsusb command

|__usb1 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (ehci_hcd ehci-platform.0) hub
|__usb2 1d6b:0001:0310 09 1.10 12MBit/s 0mA 1IF (Linux 3.10.105 ohci_hcd Generic Platform OHCI Controller ohci-platform.0) hub
|__2-1 0403:6001:0600 00 2.00 12MBit/s 90mA 1IF (RFXCOM RFXtrx433 A1Y0NLCE)
|__usb3 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (Linux 3.10.105 xhci-hcd xHCI Host Controller xhci-hcd.0.auto) hub
|__3-1 0bda:8152:2000 00 2.10 480MBit/s 100mA 2IFs (Realtek USB 10/100 LAN 00E04C361AB0)
|__usb4 1d6b:0003:0310 09 3.00 5000MBit/s 0mA 1IF (Linux 3.10.105 xhci-hcd xHCI Host Controller xhci-hcd.0.auto) hub

Output of lsusb command

|__usb1 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (ehci_hcd ehci-platform.0) hub
|__usb2 1d6b:0001:0310 09 1.10 12MBit/s 0mA 1IF (Linux 3.10.105 ohci_hcd Generic Platform OHCI Controller ohci-platform.0) hub
|__2-1 0403:6001:0600 00 2.00 12MBit/s 90mA 1IF (RFXCOM RFXtrx433 A1Y0NLCE)
|__usb3 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (Linux 3.10.105 xhci-hcd xHCI Host Controller xhci-hcd.0.auto) hub
|__3-1 0bda:8152:2000 00 2.10 480MBit/s 100mA 2IFs (Realtek USB 10/100 LAN 00E04C361AB0)
|__usb4 1d6b:0003:0310 09 3.00 5000MBit/s 0mA 1IF (Linux 3.10.105 xhci-hcd xHCI Host Controller xhci-hcd.0.auto) hub

I would like to use an ASUSTOR AS-U2.5G on a DS1815+ DSM 6.2.2

I've begun to try to compile this myself but I've not succeeded for the moment.
I tried both to cross-compile on a VM and to direct compile on the DS1815+ and got stuck, honestly my knowledge of linux is too weak and I'm not sure where to start and what to use/install.

(I'd like to see how you made it, I'm eager to learn how to do it myself.)

I had to up the USB nic with "sudo ifconfig eth4 up" and then set to DHCP in the Synology GUI portal.

Breaking w/ template format just to cross post the aquantia chip/driver has the same issue as this one does on this box.
Registers proper speeds w/ connections at both ends but real world performance is less than 1Gbps regular connection
It is pretty well detailed there, but anyone searching for the issue chip/driver can refer to that issue log for details.

bb-qq/aqc111#14 (comment)

Mentioned it might be a signal issue w/ daughterboard, or maybe issue building this for cedarview(?)

Description of the problem

Wow this is a different one. I rsynced a file between two Synology's. I ran all flavors of sha sum and md5 from the root shell and confirmed the hashes were the same. What was strange is my hash-based duplicate finders were not seeing the files as the same. In my bash terminal I checked the hashes of the files mounted to my computer over smb. What was odd was the hashes matched only one of the Synology's. The hashes produced through this driver and the pluggable 2.5gb adapter were not only different but rotating each time I checked. I disconnected the share and used another IP to mount the share from an internal nic in the nas. Now the hashes match and don't rotate. Disconnected and reconnected a few times to each and confirmed the behavior.

This is very bad. I moved 1.5TB from one nas to another and used a duplicate finder to easily remove the files from the original nas. Call me paranoid but I like to make sure I'm not deleting something that's not IDENTICAL. So out of 1.5 TB of data, my duplicate finders fond 0 files changed when using the pluggable + driver. When using the built-in nics of the computer and nas, All 1.5 TB is seen to be duplicated.

Here I was hunting down rsync issues with not actually copying the data bit for bit. I don't know that I can trust that the data I get and send through this adapter is actually intact. The whole reason I bought this nic was to speed up deduping data over smb.

Any idea what could be causing this?

Description of your products

• the product name of your NAS model
  Linux 3.10.105 #24922 SMP Wed Jul 3 16:37:24 CST 2019 x86_64 GNU/Linux synology_avoton_1815+
  DSM 6.2.2-24922-4
  Plugable USBC-2500

Description of your environment

• connect directly to a PC or using a hub
  Plugable to iMac 10.14.6

Output of dmesg command

(paste output here)

Output of lsusb command

|__usb3          1d6b:0003:0310 09  3.00 5000MBit/s 0mA 1IF  (Linux 3.10.105 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub
  |__3-1         0bda:8156:3000 00  3.20 5000MBit/s 512mA 1IF  (Realtek USB 10/100/1G/2.5G LAN 000000001)
  |__3-4         06ca:b1b1:0100 00  3.00 5000MBit/s 0mA 1IF  ( 00001234567890B3)

Output of ifconfig -a command

eth4      Link encap:Ethernet  HWaddr xx.xx.xx.xx.xx.xx
          inet addr:xx  Bcast:xx  Mask:255.255.255.252
          inet6 addr: xx
          UP BROADCAST RUNNING MULTICAST  MTU:9000  Metric:1
          RX packets:86394 errors:0 dropped:0 overruns:0 frame:0
          TX packets:38406 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:22524266 (21.4 MiB)  TX bytes:4249053 (4.0 MiB)

If you want to have on this version the drivers:
R8152 DSM 5.2-5644.zip
I tried with: Syncwire Adaptateur Ethernet USB 3.0 to RJ45, Réseau Adaptateur USB Gigabit Ethernet à 1000 Mbps
https://www.amazon.fr/gp/product/B074CDL78M/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1

1. Create a folder into /lib/modules/yournewfolders/ and insert inside 'r8152.ko' & 'cdc_ether.ko'
2. Launch the command with your terminal (ssh or telnet) : rmmod r8152 for remove the module already charged.
3. Launch the command : insmod /lib/modules/yournewfolders/r8152.ko
4. Launch the command : insmod /lib/modules/yournewfolders/cdc_ether.ko
5. INSERT YOUR ADAPTER.
6. Launch the command: ifconfig eth1 192.x.x.x netmask 255.x.x.x up
   IT'S WORKING PERFECTLY.

Ok adapter works here without any problems but only on question.

The driver works only with 1 adapter.

Is there a possibility to operate 2 adapters?

Great work, I used the Club USB-A 3.1 GEN 1 TO RJ45 2.5GB, and it worked instantly!
Only if i out a second Club adapter in the ds416play, the second usb adapter is not working.
The light blinks with interval of 30 secs, but isn't visible in /sys/class/net.
But still great work!

Description of the problem

No problem, just confirmation of working setup.

Description of your products

synology_avoton_1815+
DSM 6.2.2-24922 Update 4
Club 3D CAC-1420

Description of your environment

Only rested via direct link between NAS and a Mac Mini with 10Gbe aquantia chipset

Output of dmesg command

[ 7283.598338] usb 3-2: new SuperSpeed USB device number 3 using etxhci_hcd-170202
[ 7283.627370] etxhci_hcd-170202 0000:04:00.0: WARN Event TRB for slot 1 ep 2 with no TDs queued?
[ 7283.637036] etxhci_hcd-170202 0000:04:00.0: WARN Event TRB for slot 1 ep 3 with no TDs queued?
[ 7283.646721] etxhci_hcd-170202 0000:04:00.0: WARN Event TRB for slot 1 ep 6 with no TDs queued?
[ 7286.366332] r8152 3-2:1.0 (unregistered net_device): Get ether addr fail
[ 7286.366364] usb 3-2: USB disconnect, device number 3
[ 7286.379605] r8152 3-2:1.0 eth4: v2.12.0 (2019/04/29)
[ 7286.385164] r8152 3-2:1.0 eth4: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.

Output of lsusb command

Note: had to make sure I connected on USB port with the 5000mbps

|__usb1 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (ehci_hcd 0000:00:16.0) hub
|__1-1 8087:07db:0002 09 2.00 480MBit/s 0mA 1IF ( ffffffd1ffffffb2ffffffdbffffffad) hub
|__1-1.1 f400:f400:0100 00 2.00 480MBit/s 200mA 1IF (Synology DiskStation 6500597B8F6DAE88)
|__usb2 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (Linux 3.10.105 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub
|__2-4 051d:0002:0090 00 2.00 12MBit/s 2mA 1IF (American Power Conversion Back-UPS RS 550G FW:857.L7 .I USB FW:L7 3B1819X27861 )
|__usb3 1d6b:0003:0310 09 3.00 5000MBit/s 0mA 1IF (Linux 3.10.105 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub

Output of ifconfig -a command

Note: had to bring eth4 up manually.

Working with DS716+ and Club 3D CAC-1420 Dongle (USB A)

After installation I had to restart the Synology NAS for it to show up.

Synology Version: DSM 6.2.3-25426
Driver Version: 2.12.0-3

The notebook cpu I am using is I54200. With DS3617, I can't install it in Package Center. I don't support this file.

I have installed the r8152-braswell-2.12.0-1.spk into my DS216+ which is using Celeron N3050 (braswell) .

Then I plug ASUSTOR AS-U2.5G into the front of DS216+ with a Type-C to Type-A adapter, no other response on DSM 6.2.2.

synonet or ifconfig didn't show the additional network interface.

Will the driver work for the new nas DS920+ ?

DS1019 an the ethernet Adapter TUC-ET2G not work.

Description of the problem

DS1819+, USB lan device lost after reboot, but can be restored by manually stop and start the RTL driver package in package center.

Description of your products

Linux Orion 4.4.59+ #24922 SMP PREEMPT Tue Jan 14 15:20:58 CST 2020 x86_64 GNU/Linux synology_denverton_1819+
DSM 6.22.2-24922 update 5
Asustor AS-U2.5G dongle

Description of your environment

attached dmesg.
dmesg.txt
The symptom is that when the NAS boots up, the eth4 (USB lan) is not found by command ifconfig -a.
but after manually stop and start the RTL driver package in package center, the eth4 show up and the additional lan can be found on control panel.
In the dmesg, I tried to restart the package @ 2xx sec.
synoservice --restart pkgctl-r8152 also make the usb lan works.

Initially tried driver 2.12.0-1 but no success.
Worked straight away with driver version 2.13.0-1
Thank you very much!

Description of the problem

I simply renamed the line
arch= "apollolake"
with
arch="geminilake"
in the r8152-apollolake-2.13.0-1.spk file with NotePad++ and saved the file.

After Installation on the DS720+ the driver worked well and I have proper LAN connection
(see Daniels Video: https://www.youtube.com/watch?v=AyU7bB7BOsc)

Description of your products

• DS720+ with 10GB RAM
• DSM version 6.2.3-25426 Update 2
• 3D CAC-1420 Dongle (USB A)

Description of the problem

Kernel modules are loading but driver is not being bound to the device.

Description of your products

• DS918+
  Linux mark-NAS 4.4.59+ #24922 SMP PREEMPT Fri May 10 02:59:42 CST 2019 x86_64 GNU/Linux synology_apollolake_918+
  • DSM version 6.2.2
• TUC-ET2G

Description of your environment

• connect directly to a PC
  • PC: TEG-25GECTX
• Cat.5e

Output of dmesg command

[    0.000000] Command line: root=/dev/md0 earlyprintk=apl console=ttyS2,115200n8 ihd_num=4 netif_num=2 HddHotplug=1 SataPortMap=23 sata_remap=0>2:1>3:2>0:3>1 syno_hw_version=DS918+ vender_format_version=2 syno_hdd_detect=18,179,176,175 syno_hdd_enable=21,20,19,9 syno_usb_vbus_gpio=13@0000:00:15.0@1,11@0000:00:15.0@2 sn=[1 entry removed] macs=[2 entries removed]
[    0.000000] Kernel command line: root=/dev/md0 earlyprintk=apl console=ttyS2,115200n8 ihd_num=4 netif_num=2 HddHotplug=1 SataPortMap=23 sata_remap=0>2:1>3:2>0:3>1 syno_hw_version=DS918+ vender_format_version=2 syno_hdd_detect=18,179,176,175 syno_hdd_enable=21,20,19,9 syno_usb_vbus_gpio=13@0000:00:15.0@1,11@0000:00:15.0@2 sn=[1 entry removed] macs=[2 entries removed]
[    0.000000]  Gpp#13 - Host: dev_name:usb2        - Port:1 - Polarity: ACTIVE_HIGH
[    0.000000]  Gpp#13 - Host: dev_name:usb1        - Port:3 - Polarity: ACTIVE_HIGH
[    0.000000]  Gpp#11 - Host: dev_name:usb2        - Port:2 - Polarity: ACTIVE_HIGH
[    0.000000]  Gpp#11 - Host: dev_name:usb1        - Port:1 - Polarity: ACTIVE_HIGH
...
[  100.885737] usbcore: registered new interface driver usbfs
[  100.891924] usbcore: registered new interface driver hub
[  100.897963] usbcore: registered new interface driver ethub
[  100.904152] usbcore: registered new device driver usb
[  101.222164] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[  101.529944] usb 1-4: new high-speed USB device number 2 using xhci_hcd
[  101.806030] usb 2-2: new SuperSpeed USB device number 2 using xhci_hcd
[  132.770879] usb-storage 1-4:1.0: USB Mass Storage device detected
[  132.778285] scsi host5: usb-storage 1-4:1.0
[  132.784845] usbcore: registered new interface driver usb-storage
[  132.818027] usbcore: registered new interface driver usblp
[  132.993454] usbcore: registered new interface driver usbhid
[  133.000133] usbhid: USB HID core driver
[  158.232150] usbcore: registered new interface driver r8152

Output of lsusb command

|__usb1          1d6b:0002:0404 09  2.00  480MBit/s 0mA 1IF  (Linux 4.4.59+ xhci-hcd xHCI Host Controller 0000:00:15.0) hub
  |__1-4         f400:f400:0100 00  2.00  480MBit/s 200mA 1IF  (Synology DiskStation [1 entry removed])
|__usb2          1d6b:0003:0404 09  3.00 5000MBit/s 0mA 1IF  (Linux 4.4.59+ xhci-hcd xHCI Host Controller 0000:00:15.0) hub
  |__2-2         20f4:e02b:3004 00  3.20 5000MBit/s 512mA 2IFs (Realtek USB 10/100/1G/2.5G LAN 400000001)

Output of ifconfig -a command

docker0   Link encap:Ethernet  HWaddr 02:42:D7:0C:B7:3C  
          inet addr:172.17.0.1  Bcast:172.17.255.255  Mask:255.255.0.0
          inet6 addr: fe80::42:d7ff:fe0c:b73c/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:264 errors:0 dropped:0 overruns:0 frame:0
          TX packets:707 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:40501 (39.5 KiB)  TX bytes:126576 (123.6 KiB)

docker385 Link encap:Ethernet  HWaddr 5E:4B:0D:D1:50:F9  
          inet6 addr: fe80::5c4b:dff:fed1:50f9/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:19 errors:0 dropped:0 overruns:0 frame:0
          TX packets:502 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:1906 (1.8 KiB)  TX bytes:52186 (50.9 KiB)

eth0      Link encap:Ethernet  HWaddr 00:11:32:A6:B2:9D  
          inet addr:169.254.65.116  Bcast:169.254.255.255  Mask:255.255.0.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth1      Link encap:Ethernet  HWaddr 00:11:32:A6:B2:9E  
          inet addr:192.168.1.202  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::211:32ff:fea6:b29e/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:10494 errors:0 dropped:0 overruns:0 frame:0
          TX packets:99066 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:2007218 (1.9 MiB)  TX bytes:143292007 (136.6 MiB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:2898 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2898 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1 
          RX bytes:362172 (353.6 KiB)  TX bytes:362172 (353.6 KiB)

sit0      Link encap:IPv6-in-IPv4
          NOARP  MTU:1480  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

Description of the problem

RTL8153 can be successfully recognized in DS218+ control panel after driver installation. However, VMM cannot get this interface. Also, after LEDE launch in VMM, this USB interface just gets lost in control panel as well.

Description of your products

DS218+
DSM 6.2.3-25426 Update 2
RTL8153 Gigabit Ethernet Adapter (CE-LINK)

root@DS218:~# dmesg | grep -i 8152
[ 90.520673] r8152: module verification failed: signature and/or required key missing - tainting kernel
[ 90.650959] usbcore: registered new interface driver r8152
[ 90.925962] r8152 2-2:1.0 eth1: v2.12.0 (2019/04/29)
[ 90.931546] r8152 2-2:1.0 eth1: This product is covered by one or more of the following patents:
[ 1708.401014] r8152 2-3:1.0 eth1: v2.12.0 (2019/04/29)
[ 1708.406659] r8152 2-3:1.0 eth1: This product is covered by one or more of the following patents:
[ 4283.871200] r8152 2-3:1.0 eth1: v2.12.0 (2019/04/29)
[ 4283.876916] r8152 2-3:1.0 eth1: This product is covered by one or more of the following patents:

root@DS218:~# synonet
Copyright (c) 2003-2019 Synology Inc. All rights reserved.

Usage: synonet (Version 24922)
--help
--show
--dhcp iface
--manual iface ip mask
--check ip {mask}
--la_new bondX {1|2} ethX ethX
--la_del bondX
--la_enum
--la_get bondX
--la_exist
--set_gateway gateway
--set_dns dns
--dns_update
--set_mtu iface MTU
--set_hostname new_hostname
--get_hostname
--vlan_enum
--vlan_create device vlan_id {dhcp| ip mask}
--vlan_remove vlan_interface
--vlan_exist
--set_pppoe iface username password
--get_if pppoe
(only support pppoe now)
--wake xx:xx:xx:xx:xx:xx ethX
--get_block ethX
--set_block ethX {ha|aha|virtualization|mailplus} {true|false}
--dhcp_server_change_interface old_interface new_interface
--get_mac_addr iface {original | ha}
--set_ip -4/-6 ethx {flush | add | del} {empty | ip/prefix_len}
ex1 : --set_ip -4 eth0 add 192.168.55.66/16
ex2 : --set_ip -6 eth0 del 2001:b011:4002:f0:211:32ff:fe22:efcb/64
ex3 : --set_ip -4 eth0 flush
ex4 : --set_ip -6 eth0 flush
note : it's different from --manual, ifcfg doesn't modified
--ipv6-init (Do NOT use this after system booting)

Hallo,
ad this parameters to the start script then works this driver with bond configuration too.
Thanks....

/etc/rc.network restart
sleep 5

Behavior is the same as on DS2415+: hangup after a few minutes, no more bytes transfered.
Front USB: Does not work, even for a second.
Rear USB: Works a few minutes, Read 200MB/s, Write 205 MB/s. Read seems stable, write gives hang.

Description of the problem

Replace this line with your answer.

DS916+ an the ethernet Adapter UGREEN-CM275 not work,CM275 on DS916 + can only work normally in 1G mode, the packet loss rate in 2.5G mode is above 70%

请求超时。
来自 192.168.65.56 的回复: 字节=32 时间=1ms TTL=64
请求超时。
请求超时。
来自 192.168.65.216 的回复: 无法访问目标主机。
来自 192.168.65.216 的回复: 无法访问目标主机。
请求超时。
请求超时。
请求超时。
请求超时。
请求超时。
请求超时。
请求超时。
来自 192.168.65.56 的回复: 字节=32 时间=1ms TTL=64
请求超时。
请求超时。

192.168.65.56 的 Ping 统计信息:
    数据包: 已发送 = 173，已接收 = 40，丢失 = 133 (76% 丢失)，
往返行程的估计时间(以毫秒为单位):
    最短 = 1ms，最长 = 1008ms，平均 = 73ms
Control-C
^C

the specific link is as follows：

PC(192.168.65.216) -> AX200 -> AX86U -> AX86U_2.5G_lan -> CM275 -> DS916+_usb(192.168.65.56)

Description of your products

• the product name of your NAS model
  • and output of uname -a command
    3.10.105
  • DSM version 6.2.3-25426
• the product name of the ethernet dongle

Description of your environment

• connect directly to a PC or using a hub
  • PC: Intel ax200
  • Hub: ASUS RT-AX86U
• cable category (Cat.5e or Cat.6 or Cat.7)
  Cat.5e

Output of dmesg command

[57465.776490] usbcore: deregistering interface driver r8152
[57466.458147] etxhci_hcd-170202 0000:04:00.0: WARN Event TRB for slot 1 ep 3 with no TDs queued?
[57467.570385] usb 4-1: reset SuperSpeed USB device number 2 using etxhci_hcd-170202
[57468.200068] r8152 4-1:1.0 eth2: v2.12.0 (2019/04/29)
[57468.205650] r8152 4-1:1.0 eth2: This product is covered by one or more of the following patents:
               		US6,570,884, US6,115,776, and US6,327,625.
               
[57468.223283] usbcore: registered new interface driver r8152
[57468.295091] iSCSI:iscsi_target.c:612:iscsit_del_np CORE[0] - Removed Network Portal: 192.168.65.56:3260 on iSCSI/TCP
[57468.328312] iSCSI:iscsi_target.c:612:iscsit_del_np CORE[0] - Removed Network Portal: [fe80::2e16:dbff:fea1:2065]:3260 on iSCSI/TCP
[57469.496138] init: scsi_plugin_server main process (6066) killed by TERM signal
[57469.768463] init: iscsi_pluginserverd main process (24207) killed by TERM signal
[57469.836534] init: iscsi_pluginengined main process (24197) killed by TERM signal
[57470.104026] init: scsi_plugin_server main process (24225) killed by TERM signal
[57471.178215] init: synowsdiscoveryd main process ended, respawning
[57472.369190] init: iscsi_pluginserverd main process (24291) killed by TERM signal
[57472.388844] init: iscsi_pluginengined main process (24272) killed by TERM signal
[57472.480132] init: scsi_plugin_server main process (24326) killed by TERM signal
[57473.497174] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[57473.557766] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[57473.566920] r8152 4-1:1.0 eth2: carrier on

Output of lsusb command

|__usb1          1d6b:0002:0310 09  2.00  480MBit/s 0mA 1IF  (xhci_hcd 0000:00:14.0) hub
  |__1-5         f400:f400:0100 00  2.00  480MBit/s 200mA 1IF  (Synology DiskStation 65006B08B0E41663)
|__usb2          1d6b:0003:0310 09  3.00 5000MBit/s 0mA 1IF  (xhci_hcd 0000:00:14.0) hub
|__usb3          1d6b:0002:0310 09  2.00  480MBit/s 0mA 1IF  (Linux 3.10.105 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub
|__usb4          1d6b:0003:0310 09  3.00 5000MBit/s 0mA 1IF  (Linux 3.10.105 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub
  |__4-1         0bda:8156:3000 00  3.20 5000MBit/s 512mA 1IF  (Realtek USB 10/100/1G/2.5G LAN 000000001)
  |__4-2         174c:55aa:0100 00  3.00 5000MBit/s 144mA 1IF  (YuanTech PD2500 002014A002AF)

Output of ifconfig -a command

docker0   Link encap:Ethernet  HWaddr 02:42:62:E9:3F:DA  
          inet addr:172.17.0.1  Bcast:172.17.255.255  Mask:255.255.0.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr xxx  
          inet6 addr: xxx Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2758238 errors:0 dropped:0 overruns:0 frame:0
          TX packets:24833019 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:248392022 (236.8 MiB)  TX bytes:36913114294 (34.3 GiB)

eth1      Link encap:Ethernet  HWaddr xxx
          inet6 addr: xxx
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:650985 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3371684 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:67638991 (64.5 MiB)  TX bytes:4704031265 (4.3 GiB)

eth2      Link encap:Ethernet  HWaddr 2C:16:DB:A1:20:65  
          inet addr:192.168.65.56  Bcast:192.168.65.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1942 errors:0 dropped:0 overruns:0 frame:0
          TX packets:796 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:559976 (546.8 KiB)  TX bytes:139937 (136.6 KiB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:2278111 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2278111 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:280598364 (267.5 MiB)  TX bytes:280598364 (267.5 MiB)

ovs-syste Link encap:Ethernet  HWaddr EA:5C:E3:50:88:B6  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

ovs_bond0 Link encap:Ethernet  HWaddr 00:11:32:69:70:4B  
          inet addr:192.168.65.54  Bcast:192.168.65.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:25022 errors:0 dropped:0 overruns:0 frame:0
          TX packets:22488 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:4222477 (4.0 MiB)  TX bytes:28416228 (27.0 MiB)

sit0      Link encap:IPv6-in-IPv4
          NOARP  MTU:1480  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

tun0      Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  
          inet addr:10.233.0.1  P-t-P:10.233.0.2  Mask:255.255.255.255
          UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:0 (0.0 B)  TX bytes:4352 (4.2 KiB)

ethtool eth2
Settings for eth2:
	Supported ports: [ MII ]
	Supported link modes:   10baseT/Half 10baseT/Full 
	                        100baseT/Half 100baseT/Full 
	                        1000baseT/Full 
	                        2500baseX/Full 
	Supported pause frame use: No
	Supports auto-negotiation: Yes
	Advertised link modes:  10baseT/Half 10baseT/Full 
	                        100baseT/Half 100baseT/Full 
	                        1000baseT/Full 
	                        2500baseX/Full 
	Advertised pause frame use: Symmetric Receive-only
	Advertised auto-negotiation: Yes
	Link partner advertised link modes:  100baseT/Full 
	                                     1000baseT/Full 
	Link partner advertised pause frame use: No
	Link partner advertised auto-negotiation: Yes
	Speed: 2500Mb/s
	Duplex: Full
	Port: MII
	PHYAD: 32
	Transceiver: internal
	Auto-negotiation: on
	Supports Wake-on: pumbg
	Wake-on: g
	Current message level: 0x00007fff (32767)
			       drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol

Description of the problem

DS1019+ and uGreen 2.5G USB Ethernet Adapter (USB-C and USB3 plug) confirmed work

Replace this line with your answer.

Description of your products

• the product name of your NAS model
  DS1019+
  • and output of uname -a command
    4.4.59+
  • DSM version x.x
    DSM 6.2.2-24922 Update 6
• the product name of the ethernet dongle
  uGreen USB3.0 to RJ45 2.5G Ethernet Adapter
  https://detail.tmall.com/item.htm?id=616242333868&spm=a1z09.2.0.0.4c152e8dX56A1u&_u=15oamkp2a03&skuId=4343251704751

uGreen USB-C to RJ45 2.5G Ethernet Adapter
https://detail.tmall.com/item.htm?id=607985548355&spm=a1z09.2.0.0.4c152e8dX56A1u&_u=15oamkp3217&skuId=4272714473099

Description of your environment

• connect directly to a PC or using a hub
  • PC: NIC model name or chipset name
  • Hub: model name
• cable category (Cat.5e or Cat.6 or Cat.7)
  Direct connect to DS1019+ (Cat.6)

Output of dmesg command

(paste output here)

Output of lsusb command

(paste output here)

|__usb1 1d6b:0002:0404 09 2.00 480MBit/s 0mA 1IF (Linux 4.4.59+ xhci-hcd xHCI Host Controller 0000:00:15.0) hub
|__1-4 f400:f400:0100 00 2.00 480MBit/s 200mA 1IF (Synology DiskStation 7F00929AAACA6064)
|__usb2 1d6b:0003:0404 09 3.00 5000MBit/s 0mA 1IF (Linux 4.4.59+ xhci-hcd xHCI Host Controller 0000:00:15.0) hub
|__2-1 0bda:8156:3000 00 3.20 5000MBit/s 512mA 1IF (Realtek USB 10/100/1G/2.5G LAN 000000001)

Output of ifconfig -a command

(paste output here)

eth0 Link encap:Ethernet HWaddr
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:130125 errors:0 dropped:0 overruns:0 frame:0
TX packets:488314 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:12637561 (12.0 MiB) TX bytes:1650530982 (1.5 GiB)
Interrupt:112 base 0x6000

eth1 Link encap:Ethernet HWaddr
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:11997 errors:0 dropped:0 overruns:0 frame:0
TX packets:5531 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4092756 (3.9 MiB) TX bytes:984619 (961.5 KiB)
Interrupt:113 base 0x8000

eth2 Link encap:Ethernet HWaddr
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:41709760 errors:0 dropped:0 overruns:0 frame:0
TX packets:69123187 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:58157116001 (54.1 GiB) TX bytes:99661845078 (92.8 GiB)

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:5926 errors:0 dropped:0 overruns:0 frame:0
TX packets:5926 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:836602 (816.9 KiB) TX bytes:836602 (816.9 KiB)

sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

I had a Synology DS414 based on Marvell Armada XP MV78230, can you help to update a driver for this type CPU?

Many thanks:)

Hi,
First thanks a lot for this nice driver.
I tested 2 adapters on a Synology DS415+., USB 3.0 output.

1. Syncwire 1Gb adapter, model No. SW-AD061, Chipset RTL8153 => success !
2. CableMatters, USB 2.0 FastEthernet adapter, model No.202023, chipset RTL8152B (not 8152 afaik) => the NAS is not seen by the router (direct RJ45 link, I rebooted the NAS, ...)
   Is your package ready for RTL8152 but not for RTL8152B ? or simply it should work ?
   BRgds

NAS: DS1815+ (avaton) with 16GB RAM (2x8GB) w/two DX513's (Fully Loaded 18 drives).
DSM Version: 6.2.3-25426 Update 2
Driver version: r8152-avoton-2.12.0-3.spk
Switch: Netgear MS510TXPP (port g4, 2.5Gbps)

Notes: Informal SMB transfer speed to a Windows 10 x64 PC with NVMe SSD connected to g9 (10Gbps) QNAP QXG-10G1T (Aquantia AQtion AQC107 Chipset) results in 220MB+/sec speeds.

Since I'm running Open vSwitch for Virtual Machines on the DS1815+, I had to SSH into the box and manually run:

ifconfig eth4 up

Before if would show up in the Control Panel, allowing me to configure.

eth4      Link encap:Ethernet  HWaddr A0:CE:C8:xx:xx:xx
          inet addr:xxx.xxx.xxx.xxx  Bcast:xxx.xxx.xxx.xxx  Mask:xxx.xxx.xxx.xxx
          UP BROADCAST RUNNING MULTICAST  MTU:9000  Metric:1
          RX packets:833215 errors:0 dropped:0 overruns:0 frame:0
          TX packets:892799 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:3725217175 (3.4 GiB)  TX bytes:6681140918 (6.2 GiB)

Relevant dmesg:

[Thu Aug 20 23:32:11 2020] r8152: module verification failed: signature and/or required key missing - tainting kernel
[Thu Aug 20 23:32:11 2020] usbcore: registered new interface driver r8152
[Thu Aug 20 23:34:47 2020] usb 3-1: new SuperSpeed USB device number 2 using etxhci_hcd-170202
[Thu Aug 20 23:34:47 2020] etxhci_hcd-170202 0000:04:00.0: WARN Event TRB for slot 2 ep 2 with no TDs queued?
[Thu Aug 20 23:34:47 2020] etxhci_hcd-170202 0000:04:00.0: WARN Event TRB for slot 2 ep 3 with no TDs queued?
[Thu Aug 20 23:34:47 2020] etxhci_hcd-170202 0000:04:00.0: WARN Event TRB for slot 2 ep 6 with no TDs queued?
[Thu Aug 20 23:34:48 2020] usb 3-1: reset SuperSpeed USB device number 2 using etxhci_hcd-170202
[Thu Aug 20 23:34:48 2020] r8152 3-1:1.0 eth4: v2.12.0 (2019/04/29)
[Thu Aug 20 23:34:48 2020] r8152 3-1:1.0 eth4: This product is covered by one or more of the following patents:
                                        US6,570,884, US6,115,776, and US6,327,625.

[Thu Aug 20 23:34:50 2020] ip_tables: (C) 2000-2006 Netfilter Core Team
...
[Thu Aug 20 23:37:58 2020] r8152 3-1:1.0 eth4: carrier on
[Thu Aug 20 23:38:17 2020] usb 2-4: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes

Working perfectly well with RTL8153 based USB card (TP-link TL-UG310)

I intended to set up a link aggregation with the onboard NIC but seems to be blocked by firmware. (create link aggregation option is missing, two LANs are detected and works perfectly fine independently)

DS918+ (apollolake) confirmed working ok with Club 3D CAC-1420
DSM version: 6.2.3
Driver version: r8152-apollolake-2.13.0-1.spk
Switch: QNAP QSW-1105-5T

One issue I noticed when using USB network adapter is that IPv6 address is assigned even though the option is set to OFF in DSM.
I have not tested MTU changes.

Using rear USB port.

I found a solution to solve the problem.

In control panel -> schedule task, add a task:

user account: root
event: boot

and put your synonet related command in the task setting page -> user defined script

Done. After NAS reboot, the ASUSTOR 2.5G USB network adapter is automatically working.

Works like a charm with the Club 3D adapter. Thank you very much for your work!

Description of the problem

I have noticed that DSM tries to use this interface as it's the primary interface. It is not the first interface it routes with but it is the primary interface it wants to use for applications within DSM. This interface is connecting to a computer as a management point to point and is not being used for network ingress. I attempted to set up the Active Directory application and even Active Directory tries to use this interface for the domains NS. While I have experienced one kernel panic, I believe this is an issue with how DSM allocates adapters and not with the driver. I do not have knowledge about Synology packages so I'm not sure if there's a way in the spk to prevent the adapter from being used as the default.

Description of your products

• the product name of your NAS model
  Linux 3.10.105 #24922 SMP Wed Jul 3 16:37:24 CST 2019 x86_64 GNU/Linux synology_avoton_1815+
  DSM 6.2.2-24922-4
  Plugable USBC-2500

Description of your environment

• connect directly to a PC or using a hub
  Plugable to iMac 10.14.6

Output of dmesg command

(paste output here)

Output of lsusb command

|__usb3          1d6b:0003:0310 09  3.00 5000MBit/s 0mA 1IF  (Linux 3.10.105 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub
  |__3-1         0bda:8156:3000 00  3.20 5000MBit/s 512mA 1IF  (Realtek USB 10/100/1G/2.5G LAN 000000001)
  |__3-4         06ca:b1b1:0100 00  3.00 5000MBit/s 0mA 1IF  ( 00001234567890B3)

Output of ifconfig -a command

eth4      Link encap:Ethernet  HWaddr xx.xx.xx.xx.xx.xx
          inet addr:xx  Bcast:xx  Mask:255.255.255.252
          inet6 addr: xx
          UP BROADCAST RUNNING MULTICAST  MTU:9000  Metric:1
          RX packets:86394 errors:0 dropped:0 overruns:0 frame:0
          TX packets:38406 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:22524266 (21.4 MiB)  TX bytes:4249053 (4.0 MiB)

DSM 6.2.3-25426 Update 2
6Go RAM
Only the native driver 2.13.0-1 was installed, OK on each NAS reboot, all ethernet parameters are kept for LAN3 (= the USB 3.0 RJ45 adapter), switch NETGEAR MS510TX.

Congrats to bb-qq !!!!

Hi!
First of all, I want to say Thank you for the work you are doing.

Please add a USB network card RTL8156 VID: 0bda PID:8156
https://aliexpress.ru/item/4000982394521.html?spm=a2g0s.9042311.0.0.180e33edhvrTPm&_ga=2.95220319.257406693.1593255459-264153218.1577284876

Description of the problem

I am not adept in the wizardly ways of creating drivers, and would very much like to have a 2.5 or 5Gbps network connection with my NAS.

Description of your products

DS412+
Linux 3.10.105 #24922 SMP Wed Jul 3 16:35:48 CST 2019 x86_64 GNU/Linux synology_cedarview_412+
DSM 6.2.2
Planned: CableCreation PN B07VNFLTLD.

Description of your environment

Planned: Mikrotik RS305-1G-4S+IN switch with an ipolex 10G-SFP-T transceiver.
Planned: Mellanox Connectx-2
CAT6

Output of dmesg command

Far too much data for me to parse through for any potential doxing info... If necessary, I can email it directly to you.

Output of lsusb command

|__usb1          1d6b:0002:0310 09  2.00  480MBit/s 0mA 1IF  (ehci_hcd 0000:00:1a.7) hub
|__usb2          1d6b:0002:0310 09  2.00  480MBit/s 0mA 1IF  (ehci_hcd 0000:00:1d.7) hub
  |__2-1         f400:f400:0100 00  2.00  480MBit/s 200mA 1IF  (Synology DiskStation 650043CB10B76D76)
|__usb3          1d6b:0001:0310 09  1.10   12MBit/s 0mA 1IF  (uhci_hcd 0000:00:1a.0) hub
|__usb4          1d6b:0001:0310 09  1.10   12MBit/s 0mA 1IF  (uhci_hcd 0000:00:1d.0) hub
|__usb5          1d6b:0001:0310 09  1.10   12MBit/s 0mA 1IF  (uhci_hcd 0000:00:1d.1) hub
|__usb6          1d6b:0001:0310 09  1.10   12MBit/s 0mA 1IF  (uhci_hcd 0000:00:1d.2) hub
|__usb7          1d6b:0002:0310 09  2.00  480MBit/s 0mA 1IF  (Linux 3.10.105 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub
  |__7-1         051d:0002:0090 00  2.00   12MBit/s 2mA 1IF  (American Power Conversion Back-UPS RS 1300G FW:863.L5 .D USB FW:L5  4B1410P56556  )
|__usb8          1d6b:0003:0310 09  3.00 5000MBit/s 0mA 1IF  (Linux 3.10.105 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub