This project is a Computer Architecture course project, which is about writing a CPU from scratch with RISC-V ISA (rv32ia). It's written by verilog hardware design language. It has features as follows:

• It has five stages pipiline with meomory controller and stall controller.

• It has 512 bytes instruction cache, which can contain 128 instructions.

• It can be simulated correctly for the instructions in rv32i, except for ECALL, EBREAK, CSRRW, CSRRS, CSRRC, CSRRWI, CSRRSI, CSRRCI.

• It can generate a CPU on FPGA, simulate a memory on PC, and connect two of them by uart. And it could pass all the tests given on board with a frequency of 150M Hz.

Before we start, it's necessary to install RISC-V toolchain (cross compiler).

Here is a brief introduction about how to install RiscV toolchain on linux in 2019. First clone the official repository:

git clone https://github.com/riscv/riscv-gnu-toolchain.git && cd riscv-gnu-toolchain

This might take some time. It is suggested to add proxy for your git:

git config --global http.proxy 'socks5://127.0.0.1:1080'

Now we can start compile the toolchain

./configure --prefix=/opt/riscv --with-arch=rv32ia --with-abi=ilp32 
sudo make all 

Remark: Here --with-arch=rv32ia means we only use the ISA with 32-bit address space, 32 registers and atomic instruction (That's what A-extension means). Using --with-arch=rv32i will leads to build error.

You may wait for about an hour. After that add the toolchain to PATH.

export PATH=$PATH:/opt/riscv/bin

check if your toolchain works by

riscv32-unknown-elf-gcc -v

Here you can use the shell script I wrote. In the root directory, run script

./build.sh all
./build.sh testname

to build all test cases or only one testcase.

This will compile 'testcase/testname.c' and output some intermediate files to directory 'testdata/'. And the .data file is exactly what we need.

• Using Vivado: Just move the .data file to the src directory and run simulation.
• Using Iverilog: Iverilog is a light weight and open source simulator, which is easy to install with apt and fast to simulate. Here I wrote a script sim.sh to help me test the correctness, just type

cd src
./sim.sh testname

The five stages are the same with the classic five stage architecture. And one thing need to be dealt with is control hazard, I use a stall controller to schedule all the stuffs here

always @(*) begin
        if (rst == `RstEnable) begin
            stall <= 7'b0000000;
        end else if (stallreq_mem == `Stop) begin 
            stall <= 7'b1001111; // [5:0]
        end else if (stallreq_branch == `Stop) begin
            stall <= 7'b0100010; // cancel previous inst
        end 
        else if (stallreq_id == `Stop) begin
            stall <= 7'b0000111;
        end else if (stallreq_if == `Stop) begin
            stall <= 7'b0000001;    
        end else begin
            stall <= 7'b0000000;     
        end
    end

Due to the poor API of ram.v, we can only fetch 1 byte of data from memory per cycle. Thus it's necessary to fetch one instruction with 4 stages. Moreover, to deal with conflict between IF memory access and MEM stage memory access, we have to use a memory controller to schedule all the accesses as well as communicating with stall controller. The core of my memory controller is:

if (mem_mem_req_i) begin
    if_stall_req_o  <= 1'b0;
    mem_stall_req_o <= 1'b1;
    write_enable_o  <= mem_write_enable_i;
    mem_addr_o      <= mem_mem_addr_i;
    mem_data_o      <= mem_data_i;
    mem_write       <= mem_write_byte;
    end else if (if_mem_req_i) begin
    if_stall_req_o  <= 1'b1;
    mem_stall_req_o <= 1'b0;
    write_enable_o  <= 1'b0;
    mem_data_o      <= mem_data_i;
    mem_addr_o      <= if_mem_addr_i;
    end else begin
    if_stall_req_o  <= 1'b0;
    mem_stall_req_o <= 1'b0;
end

The instructino cache can boost the speed of instruction fetch a lot. And the implementation is simple and naive, the core of my instruction cache is the following lines:

if ((read_index_i == write_index_i) && we_i) begin 
    hit_o  <= 1'b1;
    inst_o <= write_inst_i;
end else if ((read_tag_i == rtag_c) && rvalid) begin
    hit_o  <= 1'b1;
    inst_o <= rinst_c;
end else begin
    hit_o  <= 1'b0;
    inst_o <= `ZeroWord;
end

Before having implementation, make sure there is no critical warning. For exmaple, check if one reg variable has been edited in two different @always loop.

After that, we can generate bit stream and test on board! Before testing, make sure serial is installed:

sudo apt install catkin
cd serial && make install

Now

./run_test_fpga.sh testname

[1] 手把手教你设计CPU--RISC-V处理器篇,胡振波,人民邮电出版社,2018

[2] 自己动手写CPU,雷思磊,电子工业出版社,2014