vanvught / rpidmx512-zip Goto Github PK

I see only Coloured splash screen and red LED blinking (4 times long, 4 short).
Other images works fine.

I can't get it to boot. Have tried commenting/uncommenting the various HDMI lines in config.txt but I just get a few green flashes from the Pi LEDs and a blank screen.

Same setup boots raspbian no issue.

You have Removed Art-Net Ethernet firmware, because, as you said moved to orange pi and i understand completely.
But as borders are closed, i cant find orange pi that is not shipped from china and must use raspberry pi 2 in project. Can you send me old https://github.com/vanvught/rpidmx512-zip/blob/master/rpi_circle_artnet_dmx.zip?raw=true file to test it on rpi 2?

Best Regards,
Branimir

I tried the fix in the last issue which was copying only the kernel files onto the SD, which didn't boot and with all the files on the card, the red LED stayed on on the pi and the green LED was falshing as were the ethernet port LEDs. I just copied the files to the card each time. Should I have imaged them? If not then how can I fix this.

Thanks

James

Hi, I've tried to run "opi_wifi_artnet_dmx.zip" firmware onto Orange Pi Zero LTS 512Mb and it got stuck every time.
I'd connected to serial console and thats what i see here:

U-Boot SPL 2018.09 (Mar 02 2019 - 08:59:42 +0100)
DRAM: 512 MiB
Trying to boot from MMC1


U-Boot 2018.09 (Mar 02 2019 - 08:59:42 +0100) Allwinner Technology

CPU:   Allwinner H3 (SUN8I 1680)
Model: Xunlong Orange Pi Zero
DRAM:  512 MiB
MMC:   SUNXI SD/MMC: 0
Loading Environment from FAT... OK
In:    serial
Out:   serial
Err:   serial
Net:   phy interface0
eth0: ethernet@1c30000
starting USB...
USB0:   USB EHCI 1.00
USB1:   USB OHCI 1.0
USB2:   USB EHCI 1.00
USB3:   USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0
106452 bytes read in 11 ms (9.2 MiB/s)
## Booting kernel from Legacy Image at 48000000 ...
   Image Name:   http://www.orangepi-dmx.org
   Image Type:   ARM U-Boot Standalone Program (uncompressed)
   Data Size:    106388 Bytes = 103.9 KiB
   Load Address: 40000000
   Entry Point:  40000000
   Verifying Checksum ... OK
EHCI failed to shut down host controller.
EHCI failed to shut down host controller.
   Loading Standalone Program ... OK
No display found
MX25L1605D, sector size 4096, 2097152 bytes
uboot.spi
Check difference
No difference
Done
uImage
Check difference
No difference
Done
Detected MX25L1605D with sector size 4096 total 2097152 bytes
[V1.7] Orange Pi Zero Compiled on Jun  6 2021 at 17:30:37
WiFi Art-Net 3 Node DMX Output / RDM / Pixel controller {4 Universes}
Network init ...

There is neither network.txt no ap.txt files onto SDcard, but AccessPoint never comes up.

Hello!

I am new to Raspberry Pi's. I just got my first Pi. It's a Raspberry Pi 3 B+.

I am trying to install a software that allows me to receive Art-Net on the Pi, from my lighting console, and transmit it from the Pi into WS2812 or WS2811 LED strips.. The individually addressed LED strips.

​

I have one of each strip, and an external power supply for the WS2811's - as they take 12v.

​

I have found some code that has already been made for this application - I believe - here:
https://github.com/vanvught/rpidmx512

​

How do I install it??

Or boot into it?

I'm honestly not sure if it's an OS version, or if it's intended to run as a program on the Pi's Native OS.

Some more Raspberry Pi and DMX/Art-Net info can be found here:
http://www.raspberrypi-dmx.org/

I would assume, in this case, I'm looking to install the:
Art-Net 3 DMX Node / Pixel (WS28xx / SK6812) controller {SDCard}

files..

​

I have also been pointed to this file location:
https://github.com/vanvught/rpidmx512-zip/blob/master/rpi_circle_artnet_dmx.zip

But honestly - I'm kind of running in circles here.
Not going anywhere very quickly.

​

Any help would be GREATLY appreciated!!!!!

​

Thank you ALL!

Have a great day!

​

These images seem to have lagged behind the Orange Pi Images, can you do a fresh build please?