r00li / carcluster Goto Github PK

Hello!, I have a dashboard of a VW Polo 6r (PQ25) I have managed to carry out the entire process and it connects perfectly, but the same thing happens to me as in the demonstration video, the speed drops to 0, and when I stop the vehicle and come back to accelerate it rises again, until the process is repeaHello!, I have a dashboard of a VW Polo 6r (PQ25) I have managed to carry out the entire process and it connects perfectly, but the same thing happens to me as in the demonstration video, the speed drops to 0, and when I stop the vehicle and come back to accelerate it rises again, until the process is repeated. (About 7 seconds). I have seen that with other dashboards you have managed to solve it, but in this one I have not seen a way, any ideas? Thank you!ted. (About 7 seconds). I have seen that with other dashboards you have managed to solve it, but in this one I have not seen a way, any ideas? Thank you!

Hey there, first of all, thank you for this in depth guide, really helped a lot, putting this thing (mostly) together.
Everything is functioning mostly for me except for gauge for the selected gear. That's not visible at all for me. It just doesn't show anything there. It also shows me "SAFE" above the fuel gauge. That doesn't go away with driving or resetting the cluster either. It basically won't show me the total kilometers driven and I also can't set the digital display for mph permanently on the display. Its just flashing and then disappearing, being covered by "SAFE" again. Maybe you have an idea there.

Is it possible to make adjustments to the rev counter? Its a bit off for me. On the lower rev band its pretty accurate, but when setting it to lets say 6000rpm, the gauge cluster is displaying almost 7000rpm and at 7000rpm in game, the gauge cluster is already pegged at 8000rpm. Is there a way to fine tune it?

Is it possible to have the speed displayed in finer increments for lets say Beamng? The speedo is rather choppy for me, as in, it only changed the speed in 5kmh increments, making it look rather choppy and jumpy instead of smooth. This is especially noticeable at cruising speeds.

As for the gauge cluster, its parts number 6R0920860D, date written onto the cluster is 14.02.2010 and it appears to be coming out of a Polo 6R 1.4 petrol.

Hope you got an idea, if you need to know any more, let me know!
Thanks in advance!

Can it work with BMW E60 cluster?
I have change to 100kbp and it success to control backlight, but rpm and speed
not work.

And backlight flash again and again.

Thanks!

Everything works good, but still have a DTC on it.
Looks like turning system module maybe power steering?

And a little problem.
It'a good when only RPM needle runing, but both speedo needle and rpm
rpm needle goes a little lag (few).

Sorry for my bad english. :)

Hello there, I have a very wierd question

I have a test bench for PQ platform which you can see on the picture: https://imgur.com/fyGPqXu

On my Bench is RNS510 and 3C0 907 530 L gateway module

I would like to simulate ignition message
I use MCP2515 module with my Arduino (seerduino the only difference is that u can also put it on 3.3V operation instead of 5V)

I decided to use Instroment cluster (because I knew my RNS510 uses MFD display to send radio station information to instrument cluster so it has to have connection to this blue cable) blue cable to hook inside my CAN Netowrk

I also discovered that VW PQ cars have 3 canbuses: https://imgur.com/a/FAXZZzY
Infotaiment - 100kbps
Conveniences - 100kbps
Drive train - 500kbps

I tried to receive some packets and discovered that packets were only uvailable on 500kbps drive train bus, 100kbps bus didn't have any data, but I guess ignition message should be on drive train bus anyway, and gateway would take care of forwarding it to RNS510 at the right speed

Since I sadly have no acsess to any PQ vehicle anymore so I don't have any real data

I did fine tune your PQ45 example, to maybe at least try to send speed to my RNS:
PQKlemme15GeneratorAttempt.zip

but nothing happens, if you look at this picture: https://imgur.com/PAH2PBI
RNS510 clearly doesn't see the speed packet

I know here many things can go wrong, my packet is maybe not correct, maybe I am using the wrong port to feed my CAN message to
I also have acsess to radar port on my lovly harness, but since its CAN this shouldn't matter, the way I understand this is that as long as the messages reach the gateway, then it should forward them to the right module

So I am just wondering if you maybe have some CAN data from PQ platform cars somewhere or would know if it matters to what point in the CAN network you feed your data to

Thanks for Anwsering and Best Regards

Hello there.
I have followed the wiring from ESP32 to a CAN BUS module, and also +12v/GNF/CAN H/CAN L of the F10 cluster connector.
(I am able test the CAN BUS module loop test from IDE-Example-mcp can example).

However, after compiling, and setting up the DASH web interface, I am unable to control the F10 cluster. The cluster is still in sleep mode.
(pressing the odo button wakes up but sleep again after few secs)

Question.. The DASH able to control the cluster, am I right?

If yes then it could be the cluster or the CAN BUS module?
Is there anyway to isolate where went wrong?

Thanks!