Comments (35)
brada4
commented on July 22, 2024
Nothing in the logs illustrate any stain of saned being used.
from openwrt.
saber716rus
commented on July 22, 2024
Nothing in the logs illustrate any stain of saned being used.
I had to reset it, but the problem with the repeater mode and access points remained.
from openwrt.
brada4
commented on July 22, 2024
There is nothing in the logs in that regard. Increase hostap and supplicant log amounts (level 1 ipo 2)
from openwrt.
saber716rus
commented on July 22, 2024
There is nothing in the logs in that regard. Increase hostap and supplicant log amounts (level 1 ipo 2)
I did it on this wiki. I also noticed that the repeater was often disconnected and connected from the main router. It was not noticed before, even after setting up the print server.
https://openwrt.org/docs/guide-developer/debugging
from openwrt.
saber716rus
commented on July 22, 2024
There must be an extended log. After the reboot, everything works until I leave the repeat zone.
Thu May 30 18:50:49 2024 kern.info kernel: [ 0.560355] mt7621_gpio 1e000600.gpio: registering 32 gpios
Thu May 30 18:50:49 2024 kern.info kernel: [ 0.566374] mt7621_gpio 1e000600.gpio: registering 32 gpios
Thu May 30 18:50:49 2024 kern.info kernel: [ 0.572543] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
Thu May 30 18:50:49 2024 kern.info kernel: [ 0.579216] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 0.587983] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000
Thu May 30 18:50:49 2024 kern.info kernel: [ 0.596091] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
Thu May 30 18:50:49 2024 kern.info kernel: [ 0.961348] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
Thu May 30 18:50:49 2024 kern.info kernel: [ 0.968243] mt7621-pci 1e140000.pcie: PCIE0 enabled
Thu May 30 18:50:49 2024 kern.info kernel: [ 0.973126] mt7621-pci 1e140000.pcie: PCIE1 enabled
Thu May 30 18:50:49 2024 kern.info kernel: [ 0.977937] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
Thu May 30 18:50:49 2024 kern.info kernel: [ 0.985096] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
Thu May 30 18:50:49 2024 kern.info kernel: [ 0.991391] pci_bus 0000:00: root bus resource [bus 00-ff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 0.996813] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.003669] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.009822] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.015772] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.021994] pci 0000:00:00.0: reg 0x14: [mem 0x60600000-0x6060ffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.028241] pci 0000:00:00.0: supports D1
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.032175] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.038733] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.044747] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.050926] pci 0000:00:01.0: reg 0x14: [mem 0x60610000-0x6061ffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.057240] pci 0000:00:01.0: supports D1
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.061158] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.069020] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.075051] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.082245] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.089379] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.096692] pci 0000:01:00.0: supports D1 D2
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.100869] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.107503] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.123627] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.128788] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.134879] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.141603] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.148744] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.155648] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.161675] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.168830] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.176044] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.183321] pci 0000:02:00.0: supports D1 D2
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.187500] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.194145] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.210325] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.215542] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.221573] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.228282] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.235493] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.242100] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.248615] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.255567] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.262137] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.269010] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.275786] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.282949] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.289658] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.296867] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.303605] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.310310] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.316393] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.322453] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.330107] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.337836] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.345521] pci 0000:00:00.0: PCI bridge to [bus 01]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.350404] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.356489] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.363220] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.370370] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.378102] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.385800] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.393490] pci 0000:00:01.0: PCI bridge to [bus 02]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.398366] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.404444] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.411153] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.420992] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.432074] printk: console [ttyS0] disabled
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.436397] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.445439] printk: console [ttyS0] enabled
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.453712] printk: bootconsole [early0] disabled
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.466589] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.473004] nand: ESMT PSU1GA30DT
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.476308] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.483893] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.493128] Signature found at block 1023 [0x07fe0000]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.498252] NMBM management region starts at block 960 [0x07800000]
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.509113] First info table with writecount 0 found in block 960
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.528753] Second info table with writecount 0 found in block 963
Thu May 30 18:50:49 2024 kern.info kernel: [ 1.535041] NMBM has been successfully attached
Thu May 30 18:50:49 2024 kern.notice kernel: [ 1.539677] 8 fixed-partitions partitions found on MTD device mt7621-nand
Thu May 30 18:50:49 2024 kern.notice kernel: [ 1.547243] Creating 8 MTD partitions on "mt7621-nand":
Thu May 30 18:50:49 2024 kern.notice kernel: [ 1.552552] 0x000000000000-0x000000080000 : "u-boot"
Thu May 30 18:50:49 2024 kern.notice kernel: [ 1.566503] 0x000000080000-0x0000000e0000 : "u-boot-env"
Thu May 30 18:50:49 2024 kern.notice kernel: [ 1.578578] 0x0000000e0000-0x0000001e0000 : "nvram"
Thu May 30 18:50:49 2024 kern.notice kernel: [ 1.599820] 0x0000001e0000-0x0000002e0000 : "factory"
Thu May 30 18:50:49 2024 kern.notice kernel: [ 1.621354] 0x0000002e0000-0x0000003e0000 : "factory2"
Thu May 30 18:50:49 2024 kern.notice kernel: [ 1.642888] 0x0000003e0000-0x0000035e0000 : "firmware"
Thu May 30 18:50:49 2024 kern.notice kernel: [ 2.416795] 2 fixed-partitions partitions found on MTD device firmware
Thu May 30 18:50:49 2024 kern.notice kernel: [ 2.423516] Creating 2 MTD partitions on "firmware":
Thu May 30 18:50:49 2024 kern.notice kernel: [ 2.428472] 0x000000000000-0x000000400000 : "kernel"
Thu May 30 18:50:49 2024 kern.notice kernel: [ 2.496013] 0x000000400000-0x000003200000 : "ubi"
Thu May 30 18:50:49 2024 kern.notice kernel: [ 3.207697] 0x0000035e0000-0x0000067e0000 : "firmware2"
Thu May 30 18:50:49 2024 kern.notice kernel: [ 3.980911] 0x0000067e0000-0x000007800000 : "jffs2"
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.374929] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.388701] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.400518] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe100000, irq 21
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.410774] i2c_dev: i2c /dev entries driver
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.418116] NET: Registered PF_INET6 protocol family
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.425646] Segment Routing with IPv6
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.429410] In-situ OAM (IOAM) with IPv6
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.433503] NET: Registered PF_PACKET protocol family
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.438641] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.452294] 8021q: 802.1Q VLAN Support v1.8
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.462764] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.487411] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.495206] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.502451] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=23)
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.515762] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=24)
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.528531] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=25)
Thu May 30 18:50:49 2024 kern.info kernel: [ 4.541168] DSA: tree 0 setup
Thu May 30 18:50:49 2024 kern.notice kernel: [ 4.547897] UBI: auto-attach mtd7
Thu May 30 18:50:49 2024 kern.notice kernel: [ 4.551247] ubi0: attaching mtd7
Thu May 30 18:50:49 2024 kern.notice kernel: [ 5.732603] ubi0: scanning is finished
Thu May 30 18:50:49 2024 kern.notice kernel: [ 5.753215] ubi0: attached mtd7 (name "ubi", size 46 MiB)
Thu May 30 18:50:49 2024 kern.notice kernel: [ 5.758652] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
Thu May 30 18:50:49 2024 kern.notice kernel: [ 5.765555] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
Thu May 30 18:50:49 2024 kern.notice kernel: [ 5.772345] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
Thu May 30 18:50:49 2024 kern.notice kernel: [ 5.779281] ubi0: good PEBs: 368, bad PEBs: 0, corrupted PEBs: 0
Thu May 30 18:50:49 2024 kern.notice kernel: [ 5.785281] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
Thu May 30 18:50:49 2024 kern.notice kernel: [ 5.792498] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1711145382
Thu May 30 18:50:49 2024 kern.notice kernel: [ 5.801627] ubi0: available PEBs: 0, total reserved PEBs: 368, PEBs reserved for bad PEB handling: 19
Thu May 30 18:50:49 2024 kern.notice kernel: [ 5.810849] ubi0: background thread "ubi_bgt0d" started, PID 324
Thu May 30 18:50:49 2024 kern.info kernel: [ 5.813366] block ubiblock0_0: created from ubi0:0(rootfs)
Thu May 30 18:50:49 2024 kern.notice kernel: [ 5.822376] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
Thu May 30 18:50:49 2024 kern.info kernel: [ 5.837525] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
Thu May 30 18:50:49 2024 kern.info kernel: [ 5.848804] Freeing unused kernel image (initmem) memory: 1224K
Thu May 30 18:50:49 2024 kern.warn kernel: [ 5.854829] This architecture does not have kernel memory protection.
Thu May 30 18:50:49 2024 kern.info kernel: [ 5.861260] Run /sbin/init as init process
Thu May 30 18:50:49 2024 kern.debug kernel: [ 5.865370] with arguments:
Thu May 30 18:50:49 2024 kern.debug kernel: [ 5.865378] /sbin/init
Thu May 30 18:50:49 2024 kern.debug kernel: [ 5.865384] with environment:
Thu May 30 18:50:49 2024 kern.debug kernel: [ 5.865389] HOME=/
Thu May 30 18:50:49 2024 kern.debug kernel: [ 5.865394] TERM=linux
Thu May 30 18:50:49 2024 user.info kernel: [ 6.329845] init: Console is alive
Thu May 30 18:50:49 2024 user.info kernel: [ 6.333950] init: - watchdog -
Thu May 30 18:50:49 2024 user.info kernel: [ 7.156339] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.215443] usbcore: registered new interface driver usbfs
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.221080] usbcore: registered new interface driver hub
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.226563] usbcore: registered new device driver usb
Thu May 30 18:50:49 2024 kern.warn kernel: [ 7.242402] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator
Thu May 30 18:50:49 2024 kern.warn kernel: [ 7.250136] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.258028] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.263412] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.276046] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.285299] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.291261] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.296617] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.304121] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.311697] hub 1-0:1.0: USB hub found
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.315592] hub 1-0:1.0: 2 ports detected
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.320660] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.329816] hub 2-0:1.0: USB hub found
Thu May 30 18:50:49 2024 kern.info kernel: [ 7.333818] hub 2-0:1.0: 1 port detected
Thu May 30 18:50:49 2024 user.info kernel: [ 7.345240] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Thu May 30 18:50:49 2024 user.info kernel: [ 7.361079] init: - preinit -
Thu May 30 18:50:49 2024 kern.notice kernel: [ 8.153687] random: jshn: uninitialized urandom read (4 bytes read)
Thu May 30 18:50:49 2024 kern.notice kernel: [ 8.273953] random: jshn: uninitialized urandom read (4 bytes read)
Thu May 30 18:50:49 2024 kern.notice kernel: [ 8.324052] random: jshn: uninitialized urandom read (4 bytes read)
Thu May 30 18:50:49 2024 kern.info kernel: [ 8.664076] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
Thu May 30 18:50:49 2024 kern.info kernel: [ 8.676685] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Thu May 30 18:50:49 2024 kern.info kernel: [ 8.681786] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
Thu May 30 18:50:49 2024 kern.info kernel: [ 8.692646] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Thu May 30 18:50:49 2024 kern.notice kernel: [ 10.879468] UBIFS (ubi0:1): Mounting in unauthenticated mode
Thu May 30 18:50:49 2024 kern.notice kernel: [ 10.885521] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 468
Thu May 30 18:50:49 2024 kern.notice kernel: [ 10.967048] UBIFS (ubi0:1): recovery needed
Thu May 30 18:50:49 2024 kern.notice kernel: [ 11.177966] UBIFS (ubi0:1): recovery completed
Thu May 30 18:50:49 2024 kern.notice kernel: [ 11.182729] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
Thu May 30 18:50:49 2024 kern.notice kernel: [ 11.190550] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
Thu May 30 18:50:49 2024 kern.notice kernel: [ 11.200460] UBIFS (ubi0:1): FS size: 38219776 bytes (36 MiB, 301 LEBs), max 311 LEBs, journal size 1904640 bytes (1 MiB, 15 LEBs)
Thu May 30 18:50:49 2024 kern.notice kernel: [ 11.212090] UBIFS (ubi0:1): reserved for root: 1805213 bytes (1762 KiB)
Thu May 30 18:50:49 2024 kern.notice kernel: [ 11.218677] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 33D19D04-14B8-4353-9231-1724A8103C43, small LPT model
Thu May 30 18:50:49 2024 user.info kernel: [ 11.246728] mount_root: switching to ubifs overlay
Thu May 30 18:50:49 2024 user.warn kernel: [ 11.269487] urandom-seed: Seeding with /etc/urandom.seed
Thu May 30 18:50:49 2024 user.info kernel: [ 11.417105] procd: - early -
Thu May 30 18:50:49 2024 user.info kernel: [ 11.420217] procd: - watchdog -
Thu May 30 18:50:49 2024 user.info kernel: [ 12.049789] procd: - watchdog -
Thu May 30 18:50:49 2024 user.info kernel: [ 12.056446] procd: - ubus -
Thu May 30 18:50:49 2024 kern.notice kernel: [ 12.155191] random: ubusd: uninitialized urandom read (4 bytes read)
Thu May 30 18:50:49 2024 kern.notice kernel: [ 12.166687] random: ubusd: uninitialized urandom read (4 bytes read)
Thu May 30 18:50:49 2024 kern.notice kernel: [ 12.175135] random: ubusd: uninitialized urandom read (4 bytes read)
Thu May 30 18:50:49 2024 user.info kernel: [ 12.189711] procd: - init -
Thu May 30 18:50:49 2024 user.info kernel: [ 12.990065] kmodloader: loading kernel modules from /etc/modules.d/*
Thu May 30 18:50:49 2024 kern.info kernel: [ 13.209086] ppdev: user-space parallel port driver
Thu May 30 18:50:49 2024 kern.info kernel: [ 13.240098] lp: driver loaded but no devices found
Thu May 30 18:50:49 2024 kern.info kernel: [ 13.251276] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
Thu May 30 18:50:49 2024 kern.info kernel: [ 13.258844] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
Thu May 30 18:50:49 2024 kern.info kernel: [ 13.281618] usbcore: registered new interface driver usblp
Thu May 30 18:50:49 2024 kern.info kernel: [ 13.470595] pci 0000:00:00.0: enabling device (0006 -> 0007)
Thu May 30 18:50:49 2024 kern.info kernel: [ 13.476326] mt7915e_hif 0000:01:00.0: enabling device (0000 -> 0002)
Thu May 30 18:50:49 2024 kern.info kernel: [ 13.483181] pci 0000:00:01.0: enabling device (0006 -> 0007)
Thu May 30 18:50:49 2024 kern.info kernel: [ 13.488909] mt7915e 0000:02:00.0: enabling device (0000 -> 0002)
Thu May 30 18:50:49 2024 kern.info kernel: [ 13.763078] mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20220929104113a
Thu May 30 18:50:49 2024 kern.info kernel: [ 13.763078]
Thu May 30 18:50:49 2024 user.info kernel: [ 14.074723] urngd: v1.0.2 started.
Thu May 30 18:50:49 2024 kern.info kernel: [ 14.157670] mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20220929104145
Thu May 30 18:50:49 2024 kern.info kernel: [ 14.191635] mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20220929104205
Thu May 30 18:50:49 2024 kern.info kernel: [ 14.403915] PPP generic driver version 2.4.2
Thu May 30 18:50:49 2024 kern.info kernel: [ 14.412597] NET: Registered PF_PPPOX protocol family
Thu May 30 18:50:49 2024 user.info kernel: [ 14.431970] kmodloader: done loading kernel modules from /etc/modules.d/*
Thu May 30 18:50:49 2024 kern.notice kernel: [ 14.619120] random: jshn: uninitialized urandom read (4 bytes read)
Thu May 30 18:50:49 2024 kern.notice kernel: [ 15.208351] random: crng init done
Thu May 30 18:50:49 2024 kern.notice kernel: [ 15.211891] random: 32 urandom warning(s) missed due to ratelimiting
Thu May 30 18:50:50 2024 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Thu May 30 18:50:50 2024 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Thu May 30 18:50:50 2024 daemon.info dnsmasq[1]: started, version 2.90 cachesize 1000
Thu May 30 18:50:50 2024 daemon.info dnsmasq[1]: DNS service limited to local subnets
Thu May 30 18:50:50 2024 daemon.info dnsmasq[1]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-nftset no-auth no-cryptohash no-DNSSEC no-ID loop-detect inotify dumpfile
Thu May 30 18:50:50 2024 daemon.info dnsmasq[1]: UBus support enabled: connected to system bus
Thu May 30 18:50:50 2024 daemon.info dnsmasq[1]: using only locally-known addresses for test
Thu May 30 18:50:50 2024 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Thu May 30 18:50:50 2024 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Thu May 30 18:50:50 2024 daemon.info dnsmasq[1]: using only locally-known addresses for local
Thu May 30 18:50:50 2024 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Thu May 30 18:50:50 2024 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Thu May 30 18:50:50 2024 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Thu May 30 18:50:50 2024 daemon.warn dnsmasq[1]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Thu May 30 18:50:50 2024 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Thu May 30 18:50:50 2024 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 0 names
Thu May 30 18:50:53 2024 user.notice : Added device handler type: bonding
Thu May 30 18:50:53 2024 user.notice : Added device handler type: 8021ad
Thu May 30 18:50:53 2024 user.notice : Added device handler type: 8021q
Thu May 30 18:50:53 2024 user.notice : Added device handler type: macvlan
Thu May 30 18:50:53 2024 user.notice : Added device handler type: veth
Thu May 30 18:50:53 2024 user.notice : Added device handler type: bridge
Thu May 30 18:50:53 2024 user.notice : Added device handler type: Network device
Thu May 30 18:50:53 2024 user.notice : Added device handler type: tunnel
Thu May 30 18:50:53 2024 daemon.notice wpa_supplicant[1331]: Successfully initialized wpa_supplicant
Thu May 30 18:50:55 2024 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/network
Thu May 30 18:50:55 2024 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/wireless
Thu May 30 18:50:55 2024 user.notice ucitrack: Setting up /etc/config/luci-splash reload dependency on /etc/config/firewall
Thu May 30 18:50:55 2024 user.notice ucitrack: Setting up /etc/config/qos reload dependency on /etc/config/firewall
Thu May 30 18:50:55 2024 user.notice ucitrack: Setting up /etc/config/miniupnpd reload dependency on /etc/config/firewall
Thu May 30 18:50:55 2024 user.notice ucitrack: Setting up /etc/config/odhcpd reload dependency on /etc/config/dhcp
Thu May 30 18:50:55 2024 user.notice ucitrack: Setting up non-init /etc/config/fstab reload handler: /sbin/block mount
Thu May 30 18:50:55 2024 user.notice ucitrack: Setting up /etc/config/system reload trigger for non-procd /etc/init.d/led
Thu May 30 18:50:55 2024 kern.info kernel: [ 22.497725] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
Thu May 30 18:50:55 2024 user.notice ucitrack: Setting up /etc/config/luci_statistics reload dependency on /etc/config/system
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.522115] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.530477] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.539137] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.550435] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.559336] br-lan: port 1(lan1) entered blocking state
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.564730] br-lan: port 1(lan1) entered disabled state
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.571701] device lan1 entered promiscuous mode
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.576377] device eth0 entered promiscuous mode
Thu May 30 18:50:56 2024 daemon.notice netifd: Interface 'lan' is enabled
Thu May 30 18:50:56 2024 daemon.notice netifd: Interface 'lan' is setting up now
Thu May 30 18:50:56 2024 daemon.notice netifd: Interface 'lan' is now up
Thu May 30 18:50:56 2024 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/system
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.612546] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.621260] br-lan: port 2(lan2) entered blocking state
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.626661] br-lan: port 2(lan2) entered disabled state
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.633861] device lan2 entered promiscuous mode
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.651213] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.660136] br-lan: port 3(lan3) entered blocking state
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.665489] br-lan: port 3(lan3) entered disabled state
Thu May 30 18:50:56 2024 kern.info kernel: [ 22.672959] device lan3 entered promiscuous mode
Thu May 30 18:50:56 2024 daemon.notice netifd: Interface 'loopback' is enabled
Thu May 30 18:50:56 2024 daemon.notice netifd: Interface 'loopback' is setting up now
Thu May 30 18:50:56 2024 daemon.notice netifd: Interface 'loopback' is now up
Thu May 30 18:50:56 2024 daemon.notice netifd: Network device 'eth0' link is up
Thu May 30 18:50:56 2024 daemon.notice netifd: Network device 'lo' link is up
Thu May 30 18:50:56 2024 daemon.notice netifd: Interface 'loopback' has link connectivity
Thu May 30 18:50:56 2024 daemon.notice netifd: radio0 (1970): WARNING: Variable 'data' does not exist or is not an array/object
Thu May 30 18:50:56 2024 daemon.notice netifd: radio1 (1971): WARNING: Variable 'data' does not exist or is not an array/object
Thu May 30 18:50:56 2024 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Thu May 30 18:50:56 2024 daemon.notice procd: /etc/rc.d/S96led: setting up led USB
Thu May 30 18:50:56 2024 daemon.notice procd: /etc/rc.d/S96led: setting up led WiFi 2.4GHz
Thu May 30 18:50:56 2024 daemon.notice procd: /etc/rc.d/S96led: setting up led WiFi 5GHz
Thu May 30 18:50:57 2024 daemon.notice hostapd: Set new config for phy phy0:
Thu May 30 18:50:57 2024 daemon.notice wpa_supplicant[1331]: Set new config for phy phy0
Thu May 30 18:50:57 2024 daemon.notice hostapd: Set new config for phy phy1:
Thu May 30 18:50:57 2024 daemon.notice wpa_supplicant[1331]: Set new config for phy phy1
Thu May 30 18:50:57 2024 authpriv.warn dropbear[2371]: Failed listening on '22': Error listening: Address not available
Thu May 30 18:50:57 2024 authpriv.info dropbear[2371]: Not backgrounding
Thu May 30 18:50:57 2024 daemon.info procd: - init complete -
Thu May 30 18:50:58 2024 daemon.notice netifd: radio0 (1970): sh: acs_survey: out of range
Thu May 30 18:50:58 2024 daemon.notice netifd: radio0 (1970): sh: acs_survey: out of range
Thu May 30 18:50:58 2024 daemon.notice wpa_supplicant[1331]: Set new config for phy phy0
Thu May 30 18:50:58 2024 daemon.notice hostapd: Set new config for phy phy0: /var/run/hostapd-phy0.conf
Thu May 30 18:50:58 2024 daemon.notice hostapd: Restart interface for phy phy0
Thu May 30 18:50:59 2024 daemon.notice hostapd: Configuration file: data: driver=nl80211 logger_syslog=127 logger_syslog_level=1 logger_stdout=127 logger_stdout_level=1 country_code=RU ieee80211d=1 hw_mode=g supported_rates=60 90 120 180 240 360 480 540 basic_rates=60 120 240 beacon_int=100 noscan=1 #num_global_macaddr=1 ieee80211n=1 ht_coex=0 ht_capab=[HT40+][LDPC][SHORT-GI-20][SHORT-GI-40][TX-STBC][RX-STBC1][MAX-AMSDU-7935] ieee80211ax=1 he_su_beamformer=1 he_su_beamformee=1 he_mu_beamformer=1 he_bss_color=128 he_spr_sr_control=3 he_default_pe_duration=4 he_rts_threshold=1023 he_mu_edca_qos_info_param_count=0 he_mu_edca_qos_info_q_ack=0 he_mu_edca_qos_info_queue_request=0 he_mu_edca_qos_info_txop_request=0 he_mu_edca_ac_be_aifsn=8 he_mu_edca_ac_be_aci=0 he_mu_edca_ac_be_ecwmin=9 he_mu_edca_ac_be_ecwmax=10 he_mu_edca_ac_be_timer=255 he_mu_edca_ac_bk_aifsn=15 he_mu_edca_ac_bk_aci=1 he_mu_edca_ac_bk_ecwmin=9 he_mu_edca_ac_bk_ecwmax=10 he_mu_edca_ac_bk_timer=255 he_mu_edca_ac_vi_ecwmin=5 he_mu_edca_ac_vi_ecwmax=7 he_mu_edca_ac_v
Thu May 30 18:50:59 2024 daemon.notice netifd: radio1 (1971): sh: out of range
Thu May 30 18:50:59 2024 daemon.notice wpa_supplicant[1331]: Set new config for phy phy1
Thu May 30 18:50:59 2024 kern.info kernel: [ 25.790975] br-lan: port 4(phy0-ap0) entered blocking state
Thu May 30 18:50:59 2024 kern.info kernel: [ 25.796671] br-lan: port 4(phy0-ap0) entered disabled state
Thu May 30 18:50:59 2024 kern.info kernel: [ 25.802831] device phy0-ap0 entered promiscuous mode
Thu May 30 18:50:59 2024 daemon.warn hostapd: nl80211: Failed to add interface phy0-ap0 into bridge br-lan: Resource busy
Thu May 30 18:50:59 2024 daemon.notice hostapd: phy0-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Thu May 30 18:50:59 2024 daemon.notice hostapd: ACS: Automatic channel selection started, this may take a bit
Thu May 30 18:50:59 2024 daemon.notice hostapd: phy0-ap0: interface state COUNTRY_UPDATE->ACS
Thu May 30 18:50:59 2024 daemon.notice hostapd: phy0-ap0: ACS-STARTED
Thu May 30 18:50:59 2024 daemon.notice hostapd: Set new config for phy phy1: /var/run/hostapd-phy1.conf
Thu May 30 18:50:59 2024 daemon.notice hostapd: Restart interface for phy phy1
Thu May 30 18:50:59 2024 daemon.notice hostapd: Configuration file: data: driver=nl80211 logger_syslog=127 logger_syslog_level=1 logger_stdout=127 logger_stdout_level=1 country_code=RU ieee80211d=1 ieee80211h=1 hw_mode=a beacon_int=100 noscan=1 tx_queue_data2_burst=2.0 #num_global_macaddr=1 ieee80211n=1 ht_coex=0 ht_capab=[HT40+][LDPC][SHORT-GI-20][SHORT-GI-40][TX-STBC][RX-STBC1][MAX-AMSDU-7935] ieee80211ac=1 vht_oper_chwidth=1 vht_oper_centr_freq_seg0_idx=-6 vht_capab=[RXLDPC][SHORT-GI-80][TX-STBC-2BY1][SU-BEAMFORMER][SU-BEAMFORMEE][MU-BEAMFORMER][MU-BEAMFORMEE][RX-ANTENNA-PATTERN][TX-ANTENNA-PATTERN][RX-STBC-1][SOUNDING-DIMENSION-2][BF-ANTENNA-2][MAX-MPDU-7991][MAX-A-MPDU-LEN-EXP7] ieee80211ax=1 he_oper_chwidth=1 he_oper_centr_freq_seg0_idx=-6 he_su_beamformer=1 he_su_beamformee=1 he_mu_beamformer=1 he_bss_color=128 he_spr_sr_control=3 he_default_pe_duration=4 he_rts_threshold=1023 he_mu_edca_qos_info_param_count=0 he_mu_edca_qos_info_q_ack=0 he_mu_edca_qos_info_queue_request=0 he_mu_edca_qos_info_txop_request=0 he_mu_edca_a
Thu May 30 18:50:59 2024 kern.info kernel: [ 25.926379] br-lan: port 5(phy1-ap0) entered blocking state
Thu May 30 18:50:59 2024 kern.info kernel: [ 25.932100] br-lan: port 5(phy1-ap0) entered disabled state
Thu May 30 18:50:59 2024 kern.info kernel: [ 25.938425] device phy1-ap0 entered promiscuous mode
Thu May 30 18:50:59 2024 kern.info kernel: [ 25.944024] br-lan: port 5(phy1-ap0) entered blocking state
Thu May 30 18:50:59 2024 kern.info kernel: [ 25.949639] br-lan: port 5(phy1-ap0) entered forwarding state
Thu May 30 18:50:59 2024 kern.info kernel: [ 25.955916] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Thu May 30 18:50:59 2024 daemon.notice hostapd: phy1-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Thu May 30 18:50:59 2024 daemon.notice hostapd: ACS: Automatic channel selection started, this may take a bit
Thu May 30 18:50:59 2024 daemon.notice hostapd: phy1-ap0: interface state COUNTRY_UPDATE->ACS
Thu May 30 18:50:59 2024 daemon.notice hostapd: phy1-ap0: ACS-STARTED
Thu May 30 18:50:59 2024 kern.info kernel: [ 25.970380] device phy1-ap0 left promiscuous mode
Thu May 30 18:50:59 2024 kern.info kernel: [ 25.975471] br-lan: port 5(phy1-ap0) entered disabled state
Thu May 30 18:50:59 2024 kern.info kernel: [ 26.023799] br-lan: port 5(phy1-ap0) entered blocking state
Thu May 30 18:50:59 2024 kern.info kernel: [ 26.029392] br-lan: port 5(phy1-ap0) entered disabled state
Thu May 30 18:50:59 2024 kern.info kernel: [ 26.035459] device phy1-ap0 entered promiscuous mode
Thu May 30 18:50:59 2024 kern.info kernel: [ 26.040710] br-lan: port 5(phy1-ap0) entered blocking state
Thu May 30 18:50:59 2024 kern.info kernel: [ 26.046341] br-lan: port 5(phy1-ap0) entered forwarding state
Thu May 30 18:50:59 2024 daemon.notice netifd: bridge 'br-lan' link is up
Thu May 30 18:50:59 2024 daemon.notice netifd: Interface 'lan' has link connectivity
Thu May 30 18:50:59 2024 daemon.notice netifd: Interface 'wwan' is enabled
Thu May 30 18:50:59 2024 daemon.notice netifd: Interface 'wwan' is disabled
Thu May 30 18:50:59 2024 daemon.notice netifd: Interface 'wwan' is enabled
Thu May 30 18:50:59 2024 daemon.notice netifd: Wireless device 'radio0' is now up
Thu May 30 18:50:59 2024 daemon.notice wpa_supplicant[1331]: Set new config for phy phy1
Thu May 30 18:50:59 2024 daemon.notice hostapd: phy1-ap0: AP-DISABLED
Thu May 30 18:50:59 2024 daemon.err hostapd: hostapd_free_hapd_data: Interface phy1-ap0 wasn't started
Thu May 30 18:50:59 2024 daemon.notice hostapd: nl80211: deinit ifname=phy1-ap0 disabled_11b_rates=0
Thu May 30 18:50:59 2024 kern.info kernel: [ 26.211001] device phy1-ap0 left promiscuous mode
Thu May 30 18:50:59 2024 kern.info kernel: [ 26.216082] br-lan: port 5(phy1-ap0) entered disabled state
Thu May 30 18:50:59 2024 daemon.notice hostapd: phy1-ap0: interface state ACS->DISABLED
Thu May 30 18:50:59 2024 daemon.notice netifd: Wireless device 'radio1' is now up
Thu May 30 18:51:00 2024 daemon.notice netifd: bridge 'br-lan' link is down
Thu May 30 18:51:00 2024 daemon.notice netifd: Interface 'lan' has link connectivity loss
Thu May 30 18:51:01 2024 daemon.notice wpa_supplicant[1331]: phy1-sta0: SME: Trying to authenticate with 52:ff:20:8c:6c:50 (SSID='SecNET' freq=5260 MHz)
Thu May 30 18:51:01 2024 kern.info kernel: [ 28.083272] phy1-sta0: authenticate with 52:ff:20:8c:6c:50
Thu May 30 18:51:01 2024 kern.info kernel: [ 28.518240] phy1-sta0: send auth to 52:ff:20:8c:6c:50 (try 1/3)
Thu May 30 18:51:02 2024 daemon.notice wpa_supplicant[1331]: phy1-sta0: SME: Trying to authenticate with 52:ff:20:8c:6c:50 (SSID='SecNET' freq=5260 MHz)
Thu May 30 18:51:02 2024 kern.info kernel: [ 28.707552] phy1-sta0: authenticate with 52:ff:20:8c:6c:50
Thu May 30 18:51:02 2024 kern.info kernel: [ 28.713164] phy1-sta0: send auth to 52:ff:20:8c:6c:50 (try 1/3)
Thu May 30 18:51:02 2024 daemon.notice wpa_supplicant[1331]: phy1-sta0: Trying to associate with 52:ff:20:8c:6c:50 (SSID='SecNET' freq=5260 MHz)
Thu May 30 18:51:02 2024 kern.info kernel: [ 28.761122] phy1-sta0: authenticated
Thu May 30 18:51:02 2024 kern.info kernel: [ 28.771501] phy1-sta0: associate with 52:ff:20:8c:6c:50 (try 1/3)
Thu May 30 18:51:02 2024 kern.info kernel: [ 28.777932] phy1-sta0: associate with 52:ff:20:8c:6c:50 (try 2/3)
Thu May 30 18:51:02 2024 kern.info kernel: [ 28.784259] phy1-sta0: associate with 52:ff:20:8c:6c:50 (try 3/3)
Thu May 30 18:51:02 2024 kern.info kernel: [ 28.790485] phy1-sta0: association with 52:ff:20:8c:6c:50 timed out
Thu May 30 18:51:04 2024 daemon.notice wpa_supplicant[1331]: phy1-sta0: SME: Trying to authenticate with 52:ff:20:8c:6c:50 (SSID='SecNET' freq=5260 MHz)
Thu May 30 18:51:04 2024 kern.info kernel: [ 30.697031] phy1-sta0: authenticate with 52:ff:20:8c:6c:50
Thu May 30 18:51:04 2024 kern.info kernel: [ 30.713932] phy1-sta0: send auth to 52:ff:20:8c:6c:50 (try 1/3)
Thu May 30 18:51:04 2024 daemon.notice wpa_supplicant[1331]: phy1-sta0: SME: Trying to authenticate with 52:ff:20:8c:6c:50 (SSID='SecNET' freq=5260 MHz)
Thu May 30 18:51:04 2024 kern.info kernel: [ 30.902644] phy1-sta0: authenticate with 52:ff:20:8c:6c:50
Thu May 30 18:51:04 2024 kern.info kernel: [ 30.908167] phy1-sta0: send auth to 52:ff:20:8c:6c:50 (try 1/3)
Thu May 30 18:51:04 2024 daemon.notice wpa_supplicant[1331]: phy1-sta0: Trying to associate with 52:ff:20:8c:6c:50 (SSID='SecNET' freq=5260 MHz)
Thu May 30 18:51:04 2024 kern.info kernel: [ 30.955924] phy1-sta0: authenticated
Thu May 30 18:51:04 2024 kern.info kernel: [ 30.961435] phy1-sta0: associate with 52:ff:20:8c:6c:50 (try 1/3)
Thu May 30 18:51:04 2024 kern.info kernel: [ 30.969461] phy1-sta0: RX AssocResp from 52:ff:20:8c:6c:50 (capab=0x1811 status=0 aid=19)
Thu May 30 18:51:04 2024 kern.info kernel: [ 30.979439] phy1-sta0: associated
Thu May 30 18:51:04 2024 daemon.notice netifd: Network device 'phy1-sta0' link is up
Thu May 30 18:51:04 2024 daemon.notice netifd: Interface 'wwan' has link connectivity
Thu May 30 18:51:04 2024 daemon.notice netifd: Interface 'wwan' is setting up now
Thu May 30 18:51:04 2024 daemon.notice wpa_supplicant[1331]: phy1-sta0: Associated with 52:ff:20:8c:6c:50
Thu May 30 18:51:04 2024 daemon.notice wpa_supplicant[1331]: phy1-sta0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
Thu May 30 18:51:04 2024 daemon.notice netifd: wwan (3135): udhcpc: started, v1.36.1
Thu May 30 18:51:04 2024 daemon.notice wpa_supplicant[1331]: phy1-sta0: Unknown event 37
Thu May 30 18:51:04 2024 daemon.notice netifd: wwan (3135): udhcpc: broadcasting discover
Thu May 30 18:51:04 2024 daemon.notice wpa_supplicant[1331]: phy1-sta0: WPA: Key negotiation completed with 52:ff:20:8c:6c:50 [PTK=CCMP GTK=CCMP]
Thu May 30 18:51:04 2024 daemon.notice wpa_supplicant[1331]: phy1-sta0: CTRL-EVENT-CONNECTED - Connection to 52:ff:20:8c:6c:50 completed [id=0 id_str=]
Thu May 30 18:51:04 2024 kern.info kernel: [ 31.372593] IPv6: ADDRCONF(NETDEV_CHANGE): phy1-sta0: link becomes ready
Thu May 30 18:51:04 2024 kern.info kernel: [ 31.416000] br-lan: port 5(phy1-ap0) entered blocking state
Thu May 30 18:51:04 2024 kern.info kernel: [ 31.421658] br-lan: port 5(phy1-ap0) entered disabled state
Thu May 30 18:51:04 2024 kern.info kernel: [ 31.427613] device phy1-ap0 entered promiscuous mode
Thu May 30 18:51:04 2024 daemon.warn hostapd: nl80211: Failed to add interface phy1-ap0 into bridge br-lan: Resource busy
Thu May 30 18:51:04 2024 daemon.notice hostapd: phy1-ap0: interface state DISABLED->COUNTRY_UPDATE
Thu May 30 18:51:04 2024 kern.info kernel: [ 31.514977] IPv6: ADDRCONF(NETDEV_CHANGE): phy1-ap0: link becomes ready
Thu May 30 18:51:04 2024 kern.info kernel: [ 31.521979] br-lan: port 5(phy1-ap0) entered blocking state
Thu May 30 18:51:04 2024 kern.info kernel: [ 31.527567] br-lan: port 5(phy1-ap0) entered forwarding state
Thu May 30 18:51:04 2024 daemon.notice netifd: Network device 'phy1-ap0' link is up
Thu May 30 18:51:04 2024 daemon.notice netifd: bridge 'br-lan' link is up
Thu May 30 18:51:04 2024 daemon.notice netifd: Interface 'lan' has link connectivity
Thu May 30 18:51:05 2024 daemon.notice hostapd: phy1-ap0: interface state COUNTRY_UPDATE->ENABLED
Thu May 30 18:51:05 2024 daemon.notice hostapd: phy1-ap0: AP-ENABLED
Thu May 30 18:51:05 2024 daemon.notice wpa_supplicant[1331]: phy1-sta0: TRANSITION-DISABLE 01
Thu May 30 18:51:05 2024 daemon.notice wpa_supplicant[1331]: phy1-sta0: Unknown event 37
Thu May 30 18:51:07 2024 daemon.notice netifd: wwan (3135): udhcpc: broadcasting discover
Thu May 30 18:51:08 2024 daemon.notice netifd: wwan (3135): udhcpc: broadcasting select for 192.168.1.93, server 192.168.1.1
Thu May 30 18:51:08 2024 daemon.notice netifd: wwan (3135): udhcpc: lease of 192.168.1.93 obtained from 192.168.1.1, lease time 25200
Thu May 30 18:51:08 2024 daemon.notice netifd: Interface 'wwan' is now up
Thu May 30 18:51:08 2024 daemon.info dnsmasq[1]: reading /tmp/resolv.conf.d/resolv.conf.auto
Thu May 30 18:51:08 2024 daemon.info dnsmasq[1]: using nameserver 192.168.1.1#53
Thu May 30 18:51:08 2024 daemon.info dnsmasq[1]: using only locally-known addresses for test
Thu May 30 18:51:08 2024 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Thu May 30 18:51:08 2024 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Thu May 30 18:51:08 2024 daemon.info dnsmasq[1]: using only locally-known addresses for local
Thu May 30 18:51:08 2024 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Thu May 30 18:51:08 2024 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Thu May 30 18:51:08 2024 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 18:51:08 2024 daemon.notice hostapd: phy0-ap0: ACS-COMPLETED freq=2437 channel=6
Thu May 30 18:51:08 2024 user.notice firewall: Reloading firewall due to ifup of wwan (phy1-sta0)
Thu May 30 18:51:09 2024 kern.info kernel: [ 35.520696] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-ap0: link becomes ready
Thu May 30 18:51:09 2024 kern.info kernel: [ 35.527836] br-lan: port 4(phy0-ap0) entered blocking state
Thu May 30 18:51:09 2024 kern.info kernel: [ 35.533526] br-lan: port 4(phy0-ap0) entered forwarding state
Thu May 30 18:51:09 2024 daemon.notice netifd: Network device 'phy0-ap0' link is up
Thu May 30 18:51:09 2024 daemon.notice hostapd: phy0-ap0: interface state ACS->ENABLED
Thu May 30 18:51:09 2024 daemon.notice hostapd: phy0-ap0: AP-ENABLED
Thu May 30 18:51:10 2024 authpriv.info dropbear[3316]: Not backgrounding
Thu May 30 19:33:11 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: start SAE authentication (RX commit, status=0 (SUCCESS))
Thu May 30 19:33:11 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: SAE authentication (RX confirm, status=0 (SUCCESS))
Thu May 30 19:33:11 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-AUTHENTICATE.indication(3a:6f:70:ef:32:05, unknown)
Thu May 30 19:33:11 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DELETEKEYS.request(3a:6f:70:ef:32:05)
Thu May 30 19:33:11 2024 daemon.notice hostapd: SAE: 3a:6f:70:ef:32:05 indicates support for SAE H2E, but did not use it
Thu May 30 19:33:15 2024 daemon.err uhttpd[1713]: [info] luci: accepted login on / for root from 192.168.1.81
Thu May 30 19:33:16 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: start SAE authentication (RX commit, status=0 (SUCCESS))
Thu May 30 19:33:16 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: SAE authentication (RX confirm, status=0 (SUCCESS))
Thu May 30 19:33:16 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-AUTHENTICATE.indication(3a:6f:70:ef:32:05, unknown)
Thu May 30 19:33:16 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DELETEKEYS.request(3a:6f:70:ef:32:05)
Thu May 30 19:33:16 2024 daemon.notice hostapd: SAE: 3a:6f:70:ef:32:05 indicates support for SAE H2E, but did not use it
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: authentication OK (open system)
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 WPA: event 0 notification
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-AUTHENTICATE.indication(3a:6f:70:ef:32:05, OPEN_SYSTEM)
Thu May 30 19:33:22 2024 daemon.info hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: authenticated
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 WPA: PMKID found from PMKSA cache eap_type=0 vlan=0
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: association OK (aid 1)
Thu May 30 19:33:22 2024 daemon.info hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: associated (aid 1)
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-REASSOCIATE.indication(3a:6f:70:ef:32:05)
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DELETEKEYS.request(3a:6f:70:ef:32:05)
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: binding station to interface 'phy0-ap0'
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 WPA: event 1 notification
Thu May 30 19:33:22 2024 daemon.notice hostapd: phy1-ap0: Prune association for 3a:6f:70:ef:32:05
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 WPA: start authentication
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.1X: unauthorizing port
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 WPA: sending 1/4 msg of 4-Way Handshake
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 WPA: received EAPOL-Key frame (2/4 Pairwise)
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 WPA: sending 3/4 msg of 4-Way Handshake
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 WPA: received EAPOL-Key frame (4/4 Pairwise)
Thu May 30 19:33:22 2024 daemon.notice hostapd: phy0-ap0: AP-STA-CONNECTED 3a:6f:70:ef:32:05 auth_alg=open
Thu May 30 19:33:22 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.1X: authorizing port
Thu May 30 19:33:22 2024 daemon.info hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 WPA: pairwise key handshake completed (RSN)
Thu May 30 19:33:22 2024 daemon.notice hostapd: phy0-ap0: EAPOL-4WAY-HS-COMPLETED 3a:6f:70:ef:32:05
Thu May 30 19:33:24 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DISASSOCIATE.indication(3a:6f:70:ef:32:05, 1)
Thu May 30 19:33:24 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DELETEKEYS.request(3a:6f:70:ef:32:05)
Thu May 30 19:33:52 2024 daemon.info hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
Thu May 30 19:33:52 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DEAUTHENTICATE.indication(3a:6f:70:ef:32:05, 2)
Thu May 30 19:33:52 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DELETEKEYS.request(3a:6f:70:ef:32:05)
Thu May 30 19:34:59 2024 daemon.err uhttpd[1713]: [info] luci: accepted login on / for root from 192.168.1.1
Thu May 30 19:35:21 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: start SAE authentication (RX commit, status=0 (SUCCESS))
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: SAE authentication (RX confirm, status=0 (SUCCESS))
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 MLME: MLME-AUTHENTICATE.indication(84:3e:1d:28:af:80, unknown)
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 MLME: MLME-DELETEKEYS.request(84:3e:1d:28:af:80)
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: association OK (aid 2)
Thu May 30 19:35:22 2024 daemon.info hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: associated (aid 2)
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 MLME: MLME-REASSOCIATE.indication(84:3e:1d:28:af:80)
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 MLME: MLME-DELETEKEYS.request(84:3e:1d:28:af:80)
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: binding station to interface 'phy0-ap0'
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: event 1 notification
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: start authentication
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.1X: unauthorizing port
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: sending 1/4 msg of 4-Way Handshake
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: received EAPOL-Key frame (2/4 Pairwise)
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: sending 3/4 msg of 4-Way Handshake
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: received EAPOL-Key frame (4/4 Pairwise)
Thu May 30 19:35:22 2024 daemon.notice hostapd: phy0-ap0: AP-STA-CONNECTED 84:3e:1d:28:af:80 auth_alg=sae
Thu May 30 19:35:22 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.1X: authorizing port
Thu May 30 19:35:22 2024 daemon.info hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: pairwise key handshake completed (RSN)
Thu May 30 19:35:22 2024 daemon.notice hostapd: phy0-ap0: EAPOL-4WAY-HS-COMPLETED 84:3e:1d:28:af:80
Thu May 30 19:38:52 2024 kern.info kernel: [ 430.391557] mt7530-mdio mdio-bus:1f lan1: Link is Up - 100Mbps/Full - flow control off
Thu May 30 19:38:52 2024 kern.info kernel: [ 430.399533] br-lan: port 1(lan1) entered blocking state
Thu May 30 19:38:52 2024 kern.info kernel: [ 430.404805] br-lan: port 1(lan1) entered forwarding state
Thu May 30 19:38:52 2024 daemon.notice netifd: Network device 'lan1' link is up
Thu May 30 19:40:15 2024 daemon.err uhttpd[1713]: [info] luci: accepted login on / for root from 192.168.2.10
[ 0.000000] Linux version 5.15.150 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23809-234f1a2efa) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Fri Mar 22 22:09:42 2024
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is ASUS RT-AX53U
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 12 pages/cpu s17808 r8192 d23152 u49152
[ 0.000000] pcpu-alloc: s17808 r8192 d23152 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=00054180
[ 0.000000] Readback ErrCtl register=00054180
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 249104K/262144K available (7303K kernel code, 629K rwdata, 880K rodata, 1224K init, 225K bss, 13040K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000004] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.008047] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.066216] pid_max: default: 32768 minimum: 301
[ 0.071627] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.078840] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.090433] rcu: Hierarchical SRCU implementation.
[ 0.095921] smp: Bringing up secondary CPUs ...
[ 0.101317] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.101344] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.101359] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.101402] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.160699] Synchronize counters for CPU 1: done.
[ 0.193221] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.193242] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.193252] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.193277] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.252186] Synchronize counters for CPU 2: done.
[ 0.282826] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.282849] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.282859] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.282889] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.337370] Synchronize counters for CPU 3: done.
[ 0.367227] smp: Brought up 1 node, 4 CPUs
[ 0.376501] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.386303] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.393377] pinctrl core: initialized pinctrl subsystem
[ 0.400156] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.406743] thermal_sys: Registered thermal governor 'step_wise'
[ 0.412697] FPU Affinity set after 11720 emulations
[ 0.431349] clocksource: Switched to clocksource GIC
[ 0.437595] NET: Registered PF_INET protocol family
[ 0.442707] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.450861] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.459176] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.466846] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.474494] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.481627] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.488064] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.494571] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.501900] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.507513] PCI: CLS 0 bytes, default 32
[ 0.514231] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.526100] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.531973] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.543205] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.554500] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.560355] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.566374] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.572543] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 0.579216] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 0.587983] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000
[ 0.596091] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 0.961348] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 0.968243] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 0.973126] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 0.977937] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 0.985096] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 0.991391] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.996813] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.003669] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.009822] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.015772] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.021994] pci 0000:00:00.0: reg 0x14: [mem 0x60600000-0x6060ffff]
[ 1.028241] pci 0000:00:00.0: supports D1
[ 1.032175] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.038733] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.044747] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.050926] pci 0000:00:01.0: reg 0x14: [mem 0x60610000-0x6061ffff]
[ 1.057240] pci 0000:00:01.0: supports D1
[ 1.061158] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.069020] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280
[ 1.075051] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.082245] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.089379] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 1.096692] pci 0000:01:00.0: supports D1 D2
[ 1.100869] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.107503] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.123627] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.128788] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.134879] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.141603] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 1.148744] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.155648] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
[ 1.161675] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.168830] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.176044] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 1.183321] pci 0000:02:00.0: supports D1 D2
[ 1.187500] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.194145] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.210325] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.215542] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.221573] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
[ 1.228282] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
[ 1.235493] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.242100] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.248615] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.255567] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.262137] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.269010] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.275786] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
[ 1.282949] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff]
[ 1.289658] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref]
[ 1.296867] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
[ 1.303605] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
[ 1.310310] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff]
[ 1.316393] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 1.322453] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
[ 1.330107] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
[ 1.337836] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
[ 1.345521] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.350404] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.356489] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.363220] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 1.370370] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref]
[ 1.378102] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref]
[ 1.385800] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref]
[ 1.393490] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.398366] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 1.404444] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
[ 1.411153] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
[ 1.420992] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.432074] printk: console [ttyS0] disabled
[ 1.436397] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 1.445439] printk: console [ttyS0] enabled
[ 1.453712] printk: bootconsole [early0] disabled
[ 1.466589] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
[ 1.473004] nand: ESMT PSU1GA30DT
[ 1.476308] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.483893] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[ 1.493128] Signature found at block 1023 [0x07fe0000]
[ 1.498252] NMBM management region starts at block 960 [0x07800000]
[ 1.509113] First info table with writecount 0 found in block 960
[ 1.528753] Second info table with writecount 0 found in block 963
[ 1.535041] NMBM has been successfully attached
[ 1.539677] 8 fixed-partitions partitions found on MTD device mt7621-nand
[ 1.547243] Creating 8 MTD partitions on "mt7621-nand":
[ 1.552552] 0x000000000000-0x000000080000 : "u-boot"
[ 1.566503] 0x000000080000-0x0000000e0000 : "u-boot-env"
[ 1.578578] 0x0000000e0000-0x0000001e0000 : "nvram"
[ 1.599820] 0x0000001e0000-0x0000002e0000 : "factory"
[ 1.621354] 0x0000002e0000-0x0000003e0000 : "factory2"
[ 1.642888] 0x0000003e0000-0x0000035e0000 : "firmware"
[ 2.416795] 2 fixed-partitions partitions found on MTD device firmware
[ 2.423516] Creating 2 MTD partitions on "firmware":
[ 2.428472] 0x000000000000-0x000000400000 : "kernel"
[ 2.496013] 0x000000400000-0x000003200000 : "ubi"
[ 3.207697] 0x0000035e0000-0x0000067e0000 : "firmware2"
[ 3.980911] 0x0000067e0000-0x000007800000 : "jffs2"
[ 4.374929] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 4.388701] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 4.400518] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe100000, irq 21
[ 4.410774] i2c_dev: i2c /dev entries driver
[ 4.418116] NET: Registered PF_INET6 protocol family
[ 4.425646] Segment Routing with IPv6
[ 4.429410] In-situ OAM (IOAM) with IPv6
[ 4.433503] NET: Registered PF_PACKET protocol family
[ 4.438641] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 4.452294] 8021q: 802.1Q VLAN Support v1.8
[ 4.462764] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 4.487411] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 4.495206] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 4.502451] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=23)
[ 4.515762] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=24)
[ 4.528531] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=25)
[ 4.541168] DSA: tree 0 setup
[ 4.547897] UBI: auto-attach mtd7
[ 4.551247] ubi0: attaching mtd7
[ 5.732603] ubi0: scanning is finished
[ 5.753215] ubi0: attached mtd7 (name "ubi", size 46 MiB)
[ 5.758652] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.765555] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.772345] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.779281] ubi0: good PEBs: 368, bad PEBs: 0, corrupted PEBs: 0
[ 5.785281] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 5.792498] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1711145382
[ 5.801627] ubi0: available PEBs: 0, total reserved PEBs: 368, PEBs reserved for bad PEB handling: 19
[ 5.810849] ubi0: background thread "ubi_bgt0d" started, PID 324
[ 5.813366] block ubiblock0_0: created from ubi0:0(rootfs)
[ 5.822376] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 5.837525] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 5.848804] Freeing unused kernel image (initmem) memory: 1224K
[ 5.854829] This architecture does not have kernel memory protection.
[ 5.861260] Run /sbin/init as init process
[ 5.865370] with arguments:
[ 5.865378] /sbin/init
[ 5.865384] with environment:
[ 5.865389] HOME=/
[ 5.865394] TERM=linux
[ 6.329845] init: Console is alive
[ 6.333950] init: - watchdog -
[ 7.156339] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 7.215443] usbcore: registered new interface driver usbfs
[ 7.221080] usbcore: registered new interface driver hub
[ 7.226563] usbcore: registered new device driver usb
[ 7.242402] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator
[ 7.250136] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator
[ 7.258028] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 7.263412] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 7.276046] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
[ 7.285299] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[ 7.291261] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 7.296617] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 7.304121] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 7.311697] hub 1-0:1.0: USB hub found
[ 7.315592] hub 1-0:1.0: 2 ports detected
[ 7.320660] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 7.329816] hub 2-0:1.0: USB hub found
[ 7.333818] hub 2-0:1.0: 1 port detected
[ 7.345240] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.361079] init: - preinit -
[ 8.153687] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.273953] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.324052] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.664076] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 8.676685] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 8.681786] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 8.692646] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 10.879468] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 10.885521] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 468
[ 10.967048] UBIFS (ubi0:1): recovery needed
[ 11.177966] UBIFS (ubi0:1): recovery completed
[ 11.182729] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 11.190550] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.200460] UBIFS (ubi0:1): FS size: 38219776 bytes (36 MiB, 301 LEBs), max 311 LEBs, journal size 1904640 bytes (1 MiB, 15 LEBs)
[ 11.212090] UBIFS (ubi0:1): reserved for root: 1805213 bytes (1762 KiB)
[ 11.218677] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 33D19D04-14B8-4353-9231-1724A8103C43, small LPT model
[ 11.246728] mount_root: switching to ubifs overlay
[ 11.269487] urandom-seed: Seeding with /etc/urandom.seed
[ 11.417105] procd: - early -
[ 11.420217] procd: - watchdog -
[ 12.049789] procd: - watchdog -
[ 12.056446] procd: - ubus -
[ 12.155191] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.166687] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.175135] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.189711] procd: - init -
[ 12.990065] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.209086] ppdev: user-space parallel port driver
[ 13.240098] lp: driver loaded but no devices found
[ 13.251276] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
[ 13.258844] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
[ 13.281618] usbcore: registered new interface driver usblp
[ 13.470595] pci 0000:00:00.0: enabling device (0006 -> 0007)
[ 13.476326] mt7915e_hif 0000:01:00.0: enabling device (0000 -> 0002)
[ 13.483181] pci 0000:00:01.0: enabling device (0006 -> 0007)
[ 13.488909] mt7915e 0000:02:00.0: enabling device (0000 -> 0002)
[ 13.763078] mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20220929104113a
[ 13.763078]
[ 14.074723] urngd: v1.0.2 started.
[ 14.157670] mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20220929104145
[ 14.191635] mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20220929104205
[ 14.403915] PPP generic driver version 2.4.2
[ 14.412597] NET: Registered PF_PPPOX protocol family
[ 14.431970] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 14.619120] random: jshn: uninitialized urandom read (4 bytes read)
[ 15.208351] random: crng init done
[ 15.211891] random: 32 urandom warning(s) missed due to ratelimiting
[ 22.497725] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 22.522115] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 22.530477] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 22.539137] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 22.550435] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 22.559336] br-lan: port 1(lan1) entered blocking state
[ 22.564730] br-lan: port 1(lan1) entered disabled state
[ 22.571701] device lan1 entered promiscuous mode
[ 22.576377] device eth0 entered promiscuous mode
[ 22.612546] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 22.621260] br-lan: port 2(lan2) entered blocking state
[ 22.626661] br-lan: port 2(lan2) entered disabled state
[ 22.633861] device lan2 entered promiscuous mode
[ 22.651213] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 22.660136] br-lan: port 3(lan3) entered blocking state
[ 22.665489] br-lan: port 3(lan3) entered disabled state
[ 22.672959] device lan3 entered promiscuous mode
[ 25.790975] br-lan: port 4(phy0-ap0) entered blocking state
[ 25.796671] br-lan: port 4(phy0-ap0) entered disabled state
[ 25.802831] device phy0-ap0 entered promiscuous mode
[ 25.926379] br-lan: port 5(phy1-ap0) entered blocking state
[ 25.932100] br-lan: port 5(phy1-ap0) entered disabled state
[ 25.938425] device phy1-ap0 entered promiscuous mode
[ 25.944024] br-lan: port 5(phy1-ap0) entered blocking state
[ 25.949639] br-lan: port 5(phy1-ap0) entered forwarding state
[ 25.955916] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 25.970380] device phy1-ap0 left promiscuous mode
[ 25.975471] br-lan: port 5(phy1-ap0) entered disabled state
[ 26.023799] br-lan: port 5(phy1-ap0) entered blocking state
[ 26.029392] br-lan: port 5(phy1-ap0) entered disabled state
[ 26.035459] device phy1-ap0 entered promiscuous mode
[ 26.040710] br-lan: port 5(phy1-ap0) entered blocking state
[ 26.046341] br-lan: port 5(phy1-ap0) entered forwarding state
[ 26.211001] device phy1-ap0 left promiscuous mode
[ 26.216082] br-lan: port 5(phy1-ap0) entered disabled state
[ 28.083272] phy1-sta0: authenticate with 52:ff:20:8c:6c:50
[ 28.518240] phy1-sta0: send auth to 52:ff:20:8c:6c:50 (try 1/3)
[ 28.707552] phy1-sta0: authenticate with 52:ff:20:8c:6c:50
[ 28.713164] phy1-sta0: send auth to 52:ff:20:8c:6c:50 (try 1/3)
[ 28.761122] phy1-sta0: authenticated
[ 28.771501] phy1-sta0: associate with 52:ff:20:8c:6c:50 (try 1/3)
[ 28.777932] phy1-sta0: associate with 52:ff:20:8c:6c:50 (try 2/3)
[ 28.784259] phy1-sta0: associate with 52:ff:20:8c:6c:50 (try 3/3)
[ 28.790485] phy1-sta0: association with 52:ff:20:8c:6c:50 timed out
[ 30.697031] phy1-sta0: authenticate with 52:ff:20:8c:6c:50
[ 30.713932] phy1-sta0: send auth to 52:ff:20:8c:6c:50 (try 1/3)
[ 30.902644] phy1-sta0: authenticate with 52:ff:20:8c:6c:50
[ 30.908167] phy1-sta0: send auth to 52:ff:20:8c:6c:50 (try 1/3)
[ 30.955924] phy1-sta0: authenticated
[ 30.961435] phy1-sta0: associate with 52:ff:20:8c:6c:50 (try 1/3)
[ 30.969461] phy1-sta0: RX AssocResp from 52:ff:20:8c:6c:50 (capab=0x1811 status=0 aid=19)
[ 30.979439] phy1-sta0: associated
[ 31.372593] IPv6: ADDRCONF(NETDEV_CHANGE): phy1-sta0: link becomes ready
[ 31.416000] br-lan: port 5(phy1-ap0) entered blocking state
[ 31.421658] br-lan: port 5(phy1-ap0) entered disabled state
[ 31.427613] device phy1-ap0 entered promiscuous mode
[ 31.514977] IPv6: ADDRCONF(NETDEV_CHANGE): phy1-ap0: link becomes ready
[ 31.521979] br-lan: port 5(phy1-ap0) entered blocking state
[ 31.527567] br-lan: port 5(phy1-ap0) entered forwarding state
[ 35.520696] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-ap0: link becomes ready
[ 35.527836] br-lan: port 4(phy0-ap0) entered blocking state
[ 35.533526] br-lan: port 4(phy0-ap0) entered forwarding state
[ 430.391557] mt7530-mdio mdio-bus:1f lan1: Link is Up - 100Mbps/Full - flow control off
[ 430.399533] br-lan: port 1(lan1) entered blocking state
[ 430.404805] br-lan: port 1(lan1) entered forwarding state
from openwrt.
saber716rus
commented on July 22, 2024
in general, after investigating a little, I found that the 5GHz access point is not yet functioning on the repeater, and if I connect to it, then either there is no Internet at all or the speed is very low.
https://www.speedtest.net/result/16316688824 - this measurement was made on a 5 GHz network.
Thu May 30 20:30:22 2024 daemon.notice hostapd: SAE: 3a:6f:70:ef:32:05 indicates support for SAE H2E, but did not use it
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2412 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2417 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2422 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2427 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2432 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2437 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2472 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2447 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2442 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2457 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2467 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2462 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: ACS: Survey for freq 2452 is missing noise floor
Thu May 30 20:30:22 2024 daemon.notice hostapd: phy0-ap0: ACS-COMPLETED freq=2412 channel=1
Thu May 30 20:30:23 2024 kern.info kernel: [ 486.048555] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-ap0: link becomes ready
Thu May 30 20:30:23 2024 kern.info kernel: [ 486.055525] br-lan: port 4(phy0-ap0) entered blocking state
Thu May 30 20:30:23 2024 kern.info kernel: [ 486.061202] br-lan: port 4(phy0-ap0) entered forwarding state
Thu May 30 20:30:23 2024 daemon.notice netifd: Network device 'phy0-ap0' link is up
Thu May 30 20:30:23 2024 daemon.notice hostapd: phy0-ap0: interface state ACS->ENABLED
Thu May 30 20:30:23 2024 daemon.notice hostapd: phy0-ap0: AP-ENABLED
Thu May 30 20:30:24 2024 daemon.notice netifd: wwan (6203): udhcpc: broadcasting select for 192.168.1.93, server 192.168.1.1
Thu May 30 20:30:25 2024 daemon.notice netifd: wwan (6203): udhcpc: lease of 192.168.1.93 obtained from 192.168.1.1, lease time 25200
Thu May 30 20:30:25 2024 daemon.notice netifd: Interface 'wwan' is now up
Thu May 30 20:30:25 2024 daemon.info dnsmasq[1]: reading /tmp/resolv.conf.d/resolv.conf.auto
Thu May 30 20:30:25 2024 daemon.info dnsmasq[1]: using nameserver 192.168.1.1#53
Thu May 30 20:30:25 2024 daemon.info dnsmasq[1]: using only locally-known addresses for test
Thu May 30 20:30:25 2024 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Thu May 30 20:30:25 2024 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Thu May 30 20:30:25 2024 daemon.info dnsmasq[1]: using only locally-known addresses for local
Thu May 30 20:30:25 2024 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Thu May 30 20:30:25 2024 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Thu May 30 20:30:25 2024 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Thu May 30 20:30:25 2024 user.notice firewall: Reloading firewall due to ifup of wwan (phy1-sta0)
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: authentication OK (open system)
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: event 0 notification
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-AUTHENTICATE.indication(3a:6f:70:ef:32:05, OPEN_SYSTEM)
Thu May 30 20:30:27 2024 daemon.info hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: authenticated
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: PMKID found from PMKSA cache eap_type=0 vlan=0
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: association OK (aid 1)
Thu May 30 20:30:27 2024 daemon.info hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: associated (aid 1)
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-REASSOCIATE.indication(3a:6f:70:ef:32:05)
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DELETEKEYS.request(3a:6f:70:ef:32:05)
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: binding station to interface 'phy1-ap0'
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: event 1 notification
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: start authentication
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.1X: unauthorizing port
Thu May 30 20:30:27 2024 authpriv.info dropbear[6368]: Not backgrounding
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: sending 1/4 msg of 4-Way Handshake
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: received EAPOL-Key frame (2/4 Pairwise)
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: sending 3/4 msg of 4-Way Handshake
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: received EAPOL-Key frame (4/4 Pairwise)
Thu May 30 20:30:27 2024 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED 3a:6f:70:ef:32:05 auth_alg=open
Thu May 30 20:30:27 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.1X: authorizing port
Thu May 30 20:30:27 2024 daemon.info hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: pairwise key handshake completed (RSN)
Thu May 30 20:30:27 2024 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED 3a:6f:70:ef:32:05
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: start SAE authentication (RX commit, status=0 (SUCCESS))
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: SAE authentication (RX confirm, status=0 (SUCCESS))
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 MLME: MLME-AUTHENTICATE.indication(84:3e:1d:28:af:80, unknown)
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 MLME: MLME-DELETEKEYS.request(84:3e:1d:28:af:80)
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: association OK (aid 1)
Thu May 30 20:32:08 2024 daemon.info hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: associated (aid 1)
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 MLME: MLME-REASSOCIATE.indication(84:3e:1d:28:af:80)
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 MLME: MLME-DELETEKEYS.request(84:3e:1d:28:af:80)
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: binding station to interface 'phy0-ap0'
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: event 1 notification
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: start authentication
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.1X: unauthorizing port
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: sending 1/4 msg of 4-Way Handshake
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: received EAPOL-Key frame (2/4 Pairwise)
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: sending 3/4 msg of 4-Way Handshake
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: received EAPOL-Key frame (4/4 Pairwise)
Thu May 30 20:32:08 2024 daemon.notice hostapd: phy0-ap0: AP-STA-CONNECTED 84:3e:1d:28:af:80 auth_alg=sae
Thu May 30 20:32:08 2024 daemon.debug hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 IEEE 802.1X: authorizing port
Thu May 30 20:32:08 2024 daemon.info hostapd: phy0-ap0: STA 84:3e:1d:28:af:80 WPA: pairwise key handshake completed (RSN)
Thu May 30 20:32:08 2024 daemon.notice hostapd: phy0-ap0: EAPOL-4WAY-HS-COMPLETED 84:3e:1d:28:af:80
from openwrt.
brada4
commented on July 22, 2024
Check the box in br-lan to bring up empty bridge.
logread includes dmesg, no need to post later smaller log.
There is client disconnect followed by client successful connect in the logs' end?
from openwrt.
saber716rus
commented on July 22, 2024
Check the box in br-lan to bring up empty bridge. logread includes dmesg, no need to post later smaller log. There is client disconnect followed by client successful connect in the logs' end?
I think so. But there is also one thing that the repeater periodically disconnects from the main router, then connects back. There have been 3 or 4 times today, but so far there have been no such outages in the evening.
when connecting to the repeater access point, I cannot access the web interface.
from openwrt.
saber716rus
commented on July 22, 2024
connected to the 5GHz repeater network, the Internet leaves much to be desired. He's right next to me.
https://www.speedtest.net/result/16317122346 - my Internet connection speed is 100mbps.
SSID: SecNET
Protocol: Wi-Fi 5 (802.11ac)
Security type: WPA personal
Manufacturer: Realtek Semiconductor Corp.
Description: Realtek 8822CE Wireless LAN 802.11n PCI-E NIC
Driver version: 2024.0.9.232
Network range: 5 GHz
Network channel: 60
Line speed (reception and transmission): 585/585 (Mbps)
Local IPv6 channel address: fe80::12a4:f942:7f17:d70a%4
IPv4 address: 192.168.1.81
IPv4 DNS servers: 192.168.1.1 (without encryption)
Physical Address (MAC): 84-3E-1D-28-AF-80
from openwrt.
saber716rus
commented on July 22, 2024
information about the repeater and main router signal
from openwrt.
saber716rus
commented on July 22, 2024
just a couple of minutes ago, the repeater's radio streams were rebooted, the Internet has stabilized a little, but the behavior is still strange.
Thu May 30 22:49:36 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: authentication OK (open system)
Thu May 30 22:49:36 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-AUTHENTICATE.indication(3a:6f:70:ef:32:05, OPEN_SYSTEM)
Thu May 30 22:49:36 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DELETEKEYS.request(3a:6f:70:ef:32:05)
Thu May 30 22:49:36 2024 daemon.info hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: authenticated
Thu May 30 22:49:36 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: No PMKSA cache entry found for SAE
Thu May 30 22:49:36 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: start SAE authentication (RX commit, status=0 (SUCCESS))
Thu May 30 22:49:36 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: SAE authentication (RX confirm, status=0 (SUCCESS))
Thu May 30 22:49:36 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-AUTHENTICATE.indication(3a:6f:70:ef:32:05, unknown)
Thu May 30 22:49:36 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DELETEKEYS.request(3a:6f:70:ef:32:05)
Thu May 30 22:49:36 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: event 0 notification
Thu May 30 22:49:36 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: No PMKSA cache entry found for SAE
Thu May 30 22:49:40 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: authentication OK (open system)
Thu May 30 22:49:40 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-AUTHENTICATE.indication(3a:6f:70:ef:32:05, OPEN_SYSTEM)
Thu May 30 22:49:40 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DELETEKEYS.request(3a:6f:70:ef:32:05)
Thu May 30 22:49:40 2024 daemon.info hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: authenticated
Thu May 30 22:49:40 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: start SAE authentication (RX commit, status=0 (SUCCESS))
Thu May 30 22:49:40 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: SAE authentication (RX confirm, status=0 (SUCCESS))
Thu May 30 22:49:40 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-AUTHENTICATE.indication(3a:6f:70:ef:32:05, unknown)
Thu May 30 22:49:40 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 WPA: event 0 notification
Thu May 30 22:49:40 2024 daemon.notice hostapd: SAE: 3a:6f:70:ef:32:05 indicates support for SAE H2E, but did not use it
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: authentication OK (open system)
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: event 0 notification
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-AUTHENTICATE.indication(3a:6f:70:ef:32:05, OPEN_SYSTEM)
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DELETEKEYS.request(3a:6f:70:ef:32:05)
Thu May 30 22:49:45 2024 daemon.info hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: authenticated
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: PMKID found from PMKSA cache eap_type=0 vlan=0
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: association OK (aid 1)
Thu May 30 22:49:45 2024 daemon.info hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: associated (aid 1)
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-REASSOCIATE.indication(3a:6f:70:ef:32:05)
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DELETEKEYS.request(3a:6f:70:ef:32:05)
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: binding station to interface 'phy1-ap0'
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: event 1 notification
Thu May 30 22:49:45 2024 daemon.notice hostapd: phy0-ap0: Prune association for 3a:6f:70:ef:32:05
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: start authentication
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.1X: unauthorizing port
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: sending 1/4 msg of 4-Way Handshake
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: received EAPOL-Key frame (2/4 Pairwise)
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: sending 3/4 msg of 4-Way Handshake
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: received EAPOL-Key frame (4/4 Pairwise)
Thu May 30 22:49:45 2024 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED 3a:6f:70:ef:32:05 auth_alg=open
Thu May 30 22:49:45 2024 daemon.debug hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.1X: authorizing port
Thu May 30 22:49:45 2024 daemon.info hostapd: phy1-ap0: STA 3a:6f:70:ef:32:05 WPA: pairwise key handshake completed (RSN)
Thu May 30 22:49:45 2024 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED 3a:6f:70:ef:32:05
Thu May 30 22:49:47 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DISASSOCIATE.indication(3a:6f:70:ef:32:05, 1)
Thu May 30 22:49:47 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DELETEKEYS.request(3a:6f:70:ef:32:05)
Thu May 30 22:50:15 2024 daemon.info hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
Thu May 30 22:50:15 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DEAUTHENTICATE.indication(3a:6f:70:ef:32:05, 2)
Thu May 30 22:50:15 2024 daemon.debug hostapd: phy0-ap0: STA 3a:6f:70:ef:32:05 MLME: MLME-DELETEKEYS.request(3a:6f:70:ef:32:05)
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: start SAE authentication (RX commit, status=0 (SUCCESS))
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: SAE authentication (RX confirm, status=0 (SUCCESS))
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 MLME: MLME-AUTHENTICATE.indication(84:3e:1d:28:af:80, unknown)
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 MLME: MLME-DELETEKEYS.request(84:3e:1d:28:af:80)
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: association OK (aid 2)
Thu May 30 22:50:59 2024 daemon.notice hostapd: phy1-ap0: STA-OPMODE-N_SS-CHANGED 84:3e:1d:28:af:80 2
Thu May 30 22:50:59 2024 daemon.info hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: associated (aid 2)
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 MLME: MLME-REASSOCIATE.indication(84:3e:1d:28:af:80)
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 MLME: MLME-DELETEKEYS.request(84:3e:1d:28:af:80)
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 IEEE 802.11: binding station to interface 'phy1-ap0'
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 WPA: event 1 notification
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 WPA: start authentication
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 IEEE 802.1X: unauthorizing port
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 WPA: sending 1/4 msg of 4-Way Handshake
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 WPA: received EAPOL-Key frame (2/4 Pairwise)
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 WPA: sending 3/4 msg of 4-Way Handshake
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 WPA: received EAPOL-Key frame (4/4 Pairwise)
Thu May 30 22:50:59 2024 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED 84:3e:1d:28:af:80 auth_alg=sae
Thu May 30 22:50:59 2024 daemon.debug hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 IEEE 802.1X: authorizing port
Thu May 30 22:50:59 2024 daemon.info hostapd: phy1-ap0: STA 84:3e:1d:28:af:80 WPA: pairwise key handshake completed (RSN)
Thu May 30 22:50:59 2024 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED 84:3e:1d:28:af:80
from openwrt.
brada4
commented on July 22, 2024
non-greenfield 2.4ghz 40Mhz is most likely at fault combined with week signal.
Please make your killometer long logs into attachments and describe your claim in original post , as it sounds absolutely absurd that sane damaged router permanently.
from openwrt.
saber716rus
commented on July 22, 2024
non-greenfield 2.4ghz 40Mhz is most likely at fault combined with week signal.
Please make your killometer long logs into attachments and describe your claim in original post , as it sounds absolutely absurd that sane damaged router permanently.
https://disk.yandex.ru/d/1zt_8Q3_fFi-JQ
https://disk.yandex.ru/d/HFzGwCJLCTqeBw
https://disk.yandex.ru/d/IS36yNrTJfDO6Q
I filled in the logs from the posts on Yandex. disk. There will be a new one now.
from openwrt.
saber716rus
commented on July 22, 2024
https://disk.yandex.ru/d/TUR-o3HeyJIQKA
I made a new log. with this log, the connection was stable.
from openwrt.
saber716rus
commented on July 22, 2024
at 9.02 there was a 5-second client shutdown. I am attaching the log.
https://disk.yandex.ru/d/JQDtnGsGAeckZQ
from openwrt.
brada4
commented on July 22, 2024
Attach files to this issue and replace pictures with english ones (or better text logs)
from openwrt.
saber716rus
commented on July 22, 2024
Attach files to this issue and replace pictures with english ones (or better text logs)
the most interesting thing is the failure in the log. i.e. from 7 a.m. to 2 p.m. the repeater was working.
from openwrt.
saber716rus
commented on July 22, 2024
I'm attaching logs
from openwrt.
brada4
commented on July 22, 2024
What is exact timeline of events logged by openwrt around events in keeneeteex.
from openwrt.
saber716rus
commented on July 22, 2024
What is exact timeline of events logged by openwrt around events in keeneeteex.
Internet loss occurs every 15-20 minutes.
from openwrt.
brada4
commented on July 22, 2024
Like in 1h dhcp lease time on your non-openwrt router?
from openwrt.
saber716rus
commented on July 22, 2024
Like in 1h dhcp lease time on your non-openwrt router?
I have reserved an ip address. I've turned on the repeater now. and I'm dropping the log from now on. https://www.speedtest.net/result/16320289736 speedtest was done on a connected 5GHz network, while being very close.
system log .txt
I'm sorry, but for keenetic os I don't know where the language is changing.
I also noticed that the devices are connected and disconnected from the main router several times.
from openwrt.
saber716rus
commented on July 22, 2024
- if you are connected to the repeater, I can't get to the luci interface via browser or ssh
from openwrt.
saber716rus
commented on July 22, 2024
this is the log of the main keenetic router
from openwrt.
saber716rus
commented on July 22, 2024
MWS_LOG__31.05.2024__18_18_39.csv
the transition log
from openwrt.
saber716rus
commented on July 22, 2024
I disabled FT roaming on keenetic and this is what I get in the repeater log.
system log with roaming mode turned off on keenatic.txt
from openwrt.
brada4
commented on July 22, 2024
wpa3 rekey chokes, set one to wpa2
from openwrt.
saber716rus
commented on July 22, 2024
wpa3 rekey chokes, set one to wpa2
by the way, as soon as I turned off FT mode on the main router, I can immediately log back into the repeater if I am connected to it.
from openwrt.
saber716rus
commented on July 22, 2024
wpa3 rekey chokes, set one to wpa2
that's what I got, the problem persists. But when I turned off FT on the main router, the situation became better, but the unstable Internet persists.
system log wpa3 to wpa2.txt
from openwrt.
saber716rus
commented on July 22, 2024
@brada4 today I sent all the collected information to keenetic support.
from openwrt.
saber716rus
commented on July 22, 2024
@brada4 today I sent all the collected information to keenetic support. they said that it is possible to cache PMKID
from openwrt.
brada4
commented on July 22, 2024
Nice, maybe they are better at guessing timezone offsets in assorted logs.
from openwrt.
saber716rus
commented on July 22, 2024
Nice, maybe they are better at guessing timezone offsets in assorted logs.
it seems to have gone, but I can't get into the repeater again and the Internet speed does not rise above 8mbps
Incoming connection
7.74 Mbps=967.10 Kbytes/s
Outgoing connection
7.52 Mbps=939.82 Kbytes/s
from openwrt.
saber716rus
commented on July 22, 2024
writes that the page is unavailable
from openwrt.
brada4
commented on July 22, 2024
You have to describe a bug and how to repeat it, otherwise forums are for random mishaps during initial setup.
Does not help posting random assorted stuff across all screens, it is not crowd of superhuman robots that will serve as your helpdesk.
from openwrt.
Related Issues (20)
- zsh: termcap.c:45:14: error: conflicting types for 'boolcodes'; have 'char *[]' HOT 7
- ASUS RT-AX53U doesn't survive first reboot HOT 19
- sed can’t handle emoji characters HOT 5
- why there no libx264 option to select HOT 8
- Comparison is always true in Realtek RTL9300 PHY/SERDES driver HOT 2
- gstreamer WARNING: erroneous pipeline: no element "h264parse" HOT 3
- snapshot: Failed to build `tools/tar` with gcc 14 HOT 14
- qmi.sh should set network modes before try to register network HOT 4
- libelf NLS supports issues HOT 2
- ip-fill is crashing HOT 2
- “Save & Apply” does not create the VXLAN interface.
- DNSMASK not listen on VIP HOT 1
- Client Isolation not working with WDS HOT 9
- [23.05] Consistent ujail crash at reboot HOT 5
- GPIO driver kernel 6.6: rtl8366s chip detection failed, err=-19 (WNDRMAC v2 / WNDR3800) HOT 70
- kernel memory corruption on Turris Omnia HOT 2
- AMPDU On N mode HOT 4
- BPI-R4: network buffering issues (with stutters) HOT 13
- “WARNING: your configuration is out of sync. Please run make menuconfig, oldconfig or defconfig!” on every build when using `make defconfig` HOT 5
- Banana Pi R4 RTC not work HOT 6
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from openwrt.