This repository contains the code for the ftDuino32 controller.

The ftDuino32 controller is an ESP32 based controller with 240*320 touchscreen and SD card. It's meant to connect via I²C to an ftDuino allowing fischertechnik toy robots to be programmed in Python and Blockly using nothing but a browser.

The ftDuino32 runs Micropython and LVGL allowing for touch based user interfaces written in Python.

Furthermore the ftDuino includes a native web server with websocket capabilities allowing to use the Blockly and CodeMirror code editors. Finally a remote view mirrors the device screen and allows to fully remote control the touchscreen interface from the browser.

In the current state of the firmware it allows the user to:

• Setup WLAN using the touchscreen
• Run custom local Python apps from internal flash space or SD card
• Write Python programs using Blockly
• Write Python programs using CodeMirror
• Import/export/rename/delete/... programs
• Trigger program execution remotely
• Get a remote live view of the devices display

• Writing a Micropython app using Blockly
• Testing the remote GUI

The final device is planned to be sold fully assembled. But you can run it on off-the-shelf breadboard components.

To run the ftDuino32 setup this way you need:

• ESP32 Wrover with PSRAM
• ILI9341 based 240*320 touch TFT
• optional SD card slot + SD card
• optional I2C level shifter to connect to ftDuino

The required wiring (VCC/GND is shared by the touch):

This build has only been tested under Linux. These instuctions may be outdated as MicroPython and LVGL are being developed rather quickly.

Clone the required 4.0 version of ESP-IDF.

git clone https://github.com/espressif/esp-idf.git
cd esp-idf
git checkout 4c81978a3e2220674a432a588292a4c860eef27b
git submodule update --init

Install the dependencies and install ESP-IDF:

cd esp-idf
python -m pip install --user -r ./requirements.txt
./install.sh
. ./export.sh

Apply patch to add the latest http server including websocket support to the ESP-IDF 4.0:

cd esp-idf
patch -p1 < esp-idf.patch

Clone Micropyton and install its dependencies:

sudo apt-get install build-essential libreadline-dev libffi-dev git pkg-config libsdl2-2.0-0 libsdl2-dev python3.8

git clone --recurse-submodules https://github.com/littlevgl/lv_micropython.git

Apply patches:

cd lv_micropython
patch -p1 < http_server.patch
patch -p1 < lvgl.patch
patch -p1 < uzlib_compression.patch

This will add web server support to the micropythin bindings, increase RAM access speed, add ftDuino32 LVGL theming, disable a few unused things to save memory and add zlib/gzip compression to Micropython.

cd lv_micropython
. ../esp-idf/export.sh
make -C mpy-cross
make -C ports/esp32 BOARD=GENERIC_SPIRAM deploy

This will result in the micropython firmware to be flashed to the ESP32. You can connect a terminal program like picocom at 115200 bit/s to the board and watch it boot and use the REPL.

In order to copy files into the micropython file system you need a tool like ampy. You can verify that ampy is working by entering e.g. ampy -p /dev/ttyUSB0 ls. You omit to specify the device explicitely if you install an environment variable like AMPY_PORT=/dev/ttyUSB0.

If you are using a breadboard setup with an off-the-shelf TFT touchscnreen you'll likely have to change init_gui_esp32 in gui.py to correct the screen colors and to ajust the touchscreen calibration:

    def init_gui_esp32(self):

        # Initialize ILI9341 display
        from ili9XXX import ili9341
 
        self.disp = ili9341(miso=19, mosi=23, clk=18, cs=5, dc=32, rst=27, spihost=1, power=-1, backlight=33, backlight_on=1, mhz=80, factor=4, double_buffer=True, hybrid=True, asynchronous=True, initialize=True)

        # Register xpt2046 touch driver
        from xpt2046 import xpt2046

        self.touch = xpt2046(cs=26, spihost=1, mhz=5, max_cmds=16, cal_x0 = 3783, cal_y0 = 3948, cal_x1 = 242, cal_y1 = 423, transpose = True, samples = 3)

Afterwards all files from firmware need to be copied to the internal flash. Additionally an /apps directory has to be created to hold the user generated programs. You can optionally copy some example apps there.

Finally the html pages need to be copies to the internal flash using the install script.

If everthing has been setup correctly the firmware will boot into a user interface allowing it to be integrated into any WLAN which in turn can be used to log into the ftDuino32 with a browser to write and run custom Python applications.