A fast RAM-only, k32-only, Chia plotter.

416 GiB of RAM are required to run it, plus a few more megabytes for stack space and small allocations.

This repository depends on Chia's bls-signatures repository to generate keys and plot ids, which requires Cmake. At the time of this writing Cmake 3.14+ is required by bls-signatures. See the repository for any updated build instructions.

64-bit is supported only, for obvious reasons. Only Linux is currently completed. There are several platform abstractions misisng for macOS and Windows.

Linux

NOTE: Some repositories may have cmake versions not compatible with BLS, in which case you would have to build & install Cmake yourself.

# CentOS or Amazon Linux
sudo yum install -y cmake numactl-devel

NOTE: BLS/Relic is currently not compatible with GCC 11

Install pre-requisites then run:

Linux

# Clone the repo & its submodules
git clone --recursive https://github.com/harold-b/bladebit.git

# Build bls library. Only needs to be done once.
./build-bls

# For x86
make clean && make -j$(nproc --all)

# For ARM
make clean && make -j$(nproc --all) CONFIG=release.arm

Run bladebit -h for usage and command line options.

You can support me by donating to:

• XCH: xch1xd9vlw5t3ul0chqlg3pqffy5ecq8tude8sc4v6q5r66raavczuqsr0mkwc
• BTC: bc1qy3uz29ns7jlaql36ml0ajhus4r24v8jfcja69e
• ETH: 0x70978b4236aeBDd79c6ea8602656b53acC03f591

Licensed under AGPLv3 See LICENSE. For special licensing for commercial use, please contact me.

This project synchronizes Makefiles, VS project files and VS Code c_cpp_properties.json files by a custom tool called psync which is not currently published. I created the tool a while back for cross-platform game engine development and it is scrappy-ly coded and unclean. At some point I will publish it to facilitate development.

Writes to disk only occur to the final plot file, and it is done sequentially, un-buffered, with direct I/O. This means that writes will be block-aligned. If you've gotten faster writes elsewhere in your drive than you will get with this, it is likely that it is using buffered writes, therefore it "finishes" before it actually finishes writing to disk. The kernel will handle the I/O in the background from cache (you can confirm this with tools such as iotop). The final writes here ought to pretty much saturate your sequential writes. Writes begin happening in the background at Phase 3 and will continue to do so, depending on the disk I/O throughput, through the next plot, if it did not finish beforehand. At some point in Phase 1 of the next plot, it might stall if it still has not finished writing to disk and a buffer it requires is still being written to disk. On the system I tested, there was no interruption when using an NVMe drive.

Pool plots have been implemented and plot id and plot memo generation tested against the chia-blockchain implementation, where it generates the exact data. More testing from the community is required to verify that the plots are properly operating with pools.

Memory is bound on interleaved mode for NUMA systems which currently gives the best performance on systems with several nodes. This can be disabled with with the -m or --no-numa switch.

This is not supported yet. Some folks have reported some gains when using huge page sizes. Although this was something I wanted to test, I focused first instead on things that did not necessarily depended on system config. But I'd like to add support for it in the future (trivial from the development point of view, I have just not configured the test system with huge page sizes).

Memory accesses are pretty tight. So some spots are saturated, and completely memory bound. That is, the CPU is already completely saturated, and won't be able to do more unless access to memory is faster. However, there are more pending optimizations, some ARM-specific, some x86-specific, and other experiments for either architecture that I'd like to implement/test. I hope to have the time to do this. But your supports will surely help.

Copyright 2021 Harold Brenes