Run Command:
pip install -r requirements.txt
python manage.py runserver
- To change IP and Port
API: $ curl --data "{"ip" : "192.168.1.40","port" : "502","deviceName" : "TCPdevice01"}" http://127.0.0.1:8000/api/changetcpip
- To START ModbusTCP
API: $ curl --data "" http://127.0.0.1:8000/api/starttcp
- To STOP ModbusTCP
API: $ curl --data "" http://127.0.0.1:8000/api/stoptcp
- To START PPMP Service
API: $ curl --data "" http://127.0.0.1:8000/api/startppmp
- To STOP PPMP Service
API: $ curl --data "" http://127.0.0.1:8000/api/stopppmp
- To START ModbusRTU
API: $ curl --data "" http://127.0.0.1:8000/api/startrtu
- To STOP ModbusRTU
API: $ curl --data "" http://127.0.0.1:8000/api/stoprtu
- To read the Device Settings
API: $ curl --data "" http://127.0.0.1:8000/api/ReadDeviceSettings
- To change the EdgeGateway Properties
API: http://localhost:8000/api/changeDataCenterProperties
BODY:
{
"Name": "Edge Device",
"Mode1": "UNO-2271 Linux",
"Password": "123456",
"Identity": "S3-0001",
"IP Address": "192.168.1.15",
"Time Zone": "+05:30",
"Description": "Siqsess Edge gateway Integrate with Bosch Nexeed Platform "
}
- To Change the DataCenter-Port Properties
API: http://localhost:8000/api/changeDataCenterProperties
BODY:
{
"mode": "update",
"deviceType": "COM2",
"data": {
"Enable": "False",
"Type": "Serial",
"Name": "Selec Twix 2",
"Description": "Built in Serial port RS232/rs422/rs485",
"Scan Time(ms)": "11000",
"Time Out(ms)": "13000",
"Retry Count": "13",
"Auto Recover Time(s)": "10",
"SerialPort Setting": {
"Method": "rtu",
"Port": "COM",
"Baud Rate": "9600",
"Data Bit": "8",
"Stop Bit": "11",
"Timeout": "1",
"Parity": "N",
"RTS": "False",
"DTR": "False"
}
}
}
- To Change DataCenter-Device Properties
API: http://localhost:8000/api/changeDataCenterDeviceProperties
BODY:
{
"mode": "update",
"deviceType": "COM2",
"deviceName":"COM2-Device-02",
"data": {
"Enable": "True",
"Name": "COM2-Device-02",
"Device Type": "Modbus RTU",
"Device Model": "ADAM",
"Unit Number": "2",
"Description": "Slave 1",
"Add device name as prefix to IO Tag": "Enable",
"Extention Properties": {
"CheckSum": "Enable",
"Protocol": "Modbus",
"ModbusDigital block size": "16",
"Modbus Analog block Size": "16"
}
}
}
- To change DataCenter-Device IOTags (Sensor Properties)
API: http://localhost:8000/api/changeDataCenterDeviceIOTags
BODY:
{
"mode": "update",
"deviceType": "COM2",
"deviceName":"COM2-Device-01",
"data": [
{
"Name": "Temperature",
"Signal Type": "AI Signal",
"Conversion": "IEEE Float Point",
"Address": "6",
"Span High": "1000",
"Span Low": "0",
"Unit High": "0",
"Unit Low": "10",
"Initial Value": "0.0",
"Scan Rate": "1",
"Read Write": "Read Only",
"initvalue": "10",
"Description": "Temperature Sensor"
},
{
"Name": "Pressure",
"Signal Type": "AI",
"Conversion": "IEEE Float Point",
"Address": "1",
"Span High": "65535",
"Span Low": "0",
"Unit High": "10",
"Unit Low": "0",
"Initial Value": "0.0",
"Scan Rate": "1",
"Read Write": "Read Only",
"initvalue": "10",
"Description": "Level 1"
},
{
"Name": "Flow",
"Signal Type": "AI ",
"Conversion": "IEEE Float Point",
"Address": "2",
"Span High": "65535",
"Span Low": "0",
"Unit High": "10",
"Unit Low": "0",
"Initial Value": "0.0",
"Scan Rate": "1",
"Read Write": "Read Only",
"initvalue": "10",
"Description": "Flow 2"
}
]
}
- To Change PPMP Properties
API: http://localhost:8000/api/changeDataServiceProperties
BODY:
{
"mode": "update",
"deviceType": "PPMP",
"data": {
"Enable": "True",
"contentspec": "urn:spec://eclipse.org/unide/measurement-message#v3",
"timestamp": "2021-07-06T10:53:01.545Z"
}
}
- To Change the PPM Station Settings:
API: http://localhost:8000/api/changePpmpStations
BODY:
{
"service":"changePpmpStations",
"mode": "update",
"deviceType": "PPMP",
"StationID": "ST10",
"data": [
{
"Enable": "True",
"API": "https://demo.bosch-nexeed.com/cpm/ppm/v3/measurement",
"UpdateTime": "10",
"MeasurementTag": [
{
"TagName": "Temperature",
"TagValue": "10.0",
"Status": "updated",
"Device Name": "TCPdevice01",
"Device-Type": "TCP"
},
{
"TagName": "Pressure",
"TagValue": "11.0",
"Status": "ideal",
"Device Name": "TCPdevice01",
"Device-Type": "TCP"
}
],
"StationID": "ST10",
"DeviceID": null
}
]
} 15. To Start WebSocket
API: $ curl --data "" http://127.0.0.1:8000/api/startWebSocket
- To Stop WebSocket
API: $ curl --data "" http://127.0.0.1:8000/api/stopWebSocket
docker run -p 6379:6379 -d redis:5
{
"ip" : "192.168.1.40",
"port" : "502",
"deviceName" : "TCPdevice01"
}
docker pull siqsessjacob/boschmcm_api
docker run -t -p 8000:8000 siqsessjacob/boschmcm_api
Format:
docker exec -it (CONTAINER ID) /bin/bash
Example:
docker exec -it c2c727b2624e /bin/bash
docker run --name mcmapi --net projectnetwork --ip 172.18.0.5 -p 8000:8000 mcm-api:dev3
docker run --net projectnetwork --ip 172.18.0.22 mongo:latest
docker run --net projectnetwork --ip 172.18.0.4 redis:5
docker network inspect bosch-mcm-overall_static-network
docker network create --subnet=172.18.0.0/16 mynet123
docker run --net mynet123 --ip 172.18.0.22 -it ubuntu bash
docker network ls
version: '3'
services:
backend:
image: "mcm-api:dev3"
ports:
- "8000:8000"
depends_on:
- redis
networks:
static-network:
ipv4_address: 172.20.0.3
restart: always
frontend:
image: "siqsessjacob/mcm-ui:latest"
ports:
- "3000:3000"
depends_on:
- backend
networks:
static-network:
ipv4_address: 172.20.0.5
restart: always
redis:
image: "redis:5"
ports:
- "6379:6379"
networks:
static-network:
ipv4_address: 172.20.0.4
restart: always
networks:
static-network:
ipam:
config:
- subnet: 172.20.0.0/16
React
Typescript
Django
Laravel
Facebook
Microsoft
Google
Alibaba
D3
Tencent