TAS is a drop-in highly CPU efficient and scalable TCP acceleration service.

Our EuroSys2019 Paper describes the TAS design and its rationale.

Requirements:

• TAS is built on top of Intel DPDK for direct access to the NIC. We have tested this version with dpdk versions (17.11.9, 18.11.5, 19.11).

Assuming that dpdk is installed in ~/dpdk-inst TAS can be built as follows:

make RTE_SDK=~/dpdk-inst

This will build the TAS service (binary tas/tas), client libraries (in lib/), and a few debugging tools (in tools/).

Before running TAS the following steps are necessary:

• Make sure hugetlbfs is mounted on /dev/hugepages and enough huge pages are allocated for TAS and dpdk.
• Binding the NIC to the dpdk driver, as with any other dpdk application (for Intel NICs use vfio because uio does not support multiple interrupts).

sudo modprobe vfio-pci
sudo mount -t hugetlbfs nodev /dev/hugepages
echo 1024 | sudo tee /sys/devices/system/node/node*/hugepages/hugepages-2048kB/nr_hugepages
sudo ~/dpdk-inst/sbin/dpdk-devbind  -b vfio-pci 0000:08:00.0

To run (--ip-addr and --fp-cores-max are the minimum arguments typically needed to run tas, for more see --help):

sudo code/tas/tas --ip-addr=10.0.0.1/24 --fp-cores-max=2

Once tas is running, applications that directly link to libtas or libtas_sockets can be run directly. To run an unmodified application with sockets interposition run as follows (for example):

sudo LD_PRELOAD=lib/libtas_interpose.so ../benchmarks/micro_rpc/echoserver_linux 1234 1 foo 8192 1

For functional testing and development TAS can run in Qemu (with or without acceleration through KVM). We have tested this with the virtio dpdk driver. By default, the qemu virtio device only provides a single queue, and thus only allows TAS to run on a single core. To run a virtual machine with support for multiple queue, qemu requires a tap device with multi-queue support enabled.

Here is an example sequence of commands to create a tap device with multi queue support and then start a qemu instance that binds this tap device to a multi-queue virtio device:

sudo ip link add tastap0 type tuntap
sudo ip tuntap add mode tap multi_queue name tastap0
sudo ip link set dev tastap0 up
qemu-system-x86_64 \
    -machine q35 -cpu host \
    -drive file=vm1.qcow2,if=virtio \
    -netdev tap,ifname=tastap0,script=no,downscript=no,vhost=on,queues=8,id=nInt\
    -device virtio-net-pci,mac=52:54:00:12:34:56,vectors=18,mq=on,netdev=nInt \
    -serial mon:stdio -m 8192 -smp 16 -display none -enable-kvm

Inside the virtual machine, the following sequence of commands first takes the linux network interface down, binds it to the uio_pci_generic driver that the dpdk virtio PMD supports, and then reserves huge pages:

sudo ifconfig enp0s2 down
sudo modprobe uio
sudo modprobe uio_pci_generic
sudo dpdk-devbind.py -b uio_pci_generic 0000:00:02.0
echo 1024 | sudo tee /sys/devices/system/node/node*/hugepages/hugepages-2048kB/nr_hugepages

Virtio does not support all the NIC features that we depend on in physical NICs. In particular virtio does not support transmit checksum offload or the RSS redirection table TAS uses for scaling up and down. The dpdk virtio PMD also does not support multiple MSI-X interrupts. To run TAS given these constraints, the following command line parameters disable the use of these features (note that this implies busy polling and no autoscaling):

sudo code/tas/tas --ip-addr=10.0.0.1/24 --fp-cores-max=8 \
    --fp-no-xsumoffload --fp-no-ints --fp-no-autoscale

TAS supports the DPDK kernel NIC interface (KNI) to pass packets to the Linux kernel network stack. With KNI enabled, TAS becomes an opt-in fastpath where TAS-enabled applications operate through TAS, and other applications can use the Linux network stack as before, sharing the same physical NIC.

To run TAS with KNI the first step is to load the rte_kni kernel module. Next, when run with the --kni-name= option, TAS will create a KNI dummy network interface with the specified name. After assigning an IP address to this network interface, the Linux network stack can send and receive packets through this interface as long as TAS is running. Here is the complete sequence of commands:

sudo modprobe rte_kni
sudo code/tas/tas --ip-addr=10.0.0.1/24 --kni-name=tas0
# in separate terminal
sudo ifconfig tas0 10.0.0.1/24 up

• tas/: service implementation
  • tas/fast: TAS fast path
  • tas/slow: TAS slow path
• lib/: client libraries
  • lib/tas: lowlevel TAS client library (interface: lib/tas/include/tas_ll.h)
  • lib/sockets: socket emulation layer
• tools/: debugging tools