The Water-Efficient Industrial Navigating Robot (WEINBot) is a proof-of-concept automated industrial floor care vehicle that can effectively dislodge and collect solid grape waste from typical concrete winery flooring with minimal water use. Successful collection of solid waste before manual hose-down greatly reduces the labor and water requirements during crush season, when typical cleanings are a tedious chore that can use hundreds of gallons of water. While the device does not have the full array of sensors and software algorithms to robustly navigate the uncontrolled winery environment, basic control and sensor technologies are included so that limited demonstrations of those functionalities required for full autonomy may be accomplished. In this way, our device will serve as a good foundation for potential further robotics research to develop the automation techniques required to navigate the bustling winery environment.

The launch.c program, which compiles to weinbot by the software deploy script is a setuid binary which loads the privileged Python 2 interpreter required for the main WEINBot operating system to run.

The WEINBot OS can be run in interactive mode in ipython2 for debugging purposes. It is very mildly engineered and is meant to be used as test code for the control modules. When run in headless mode from the launcher, it runs in an infinite input loop, reading commands from the HMI module, which returns a balanced ternary tuple representing the state of the four single pole, double throw toggle switches. The HMI tuples are the keys in the dispatcher dictionary whose values are lambda functions to be called when the trigger is received. These demonstration functions are implemented in the demos module. The mode operation supervisor can also check the state of the load cell to signal when the waste bucket requires emptying.

This module is an abstraction layer over the Sabertooth module. It provides a useful drive() method that enforces speed limits and is parameterized to reflect the dimensions of the vehicle. These parameters are set in the initializer; artificial speed limits are required for both safety and the allowance of turns at maximum speed. Drive commands are given in terms of tangential speed and turning radius, so that any path can be created. Inside a critical radius, tangential speed is measured in angular units for more intuitive control that allows in-place turning.

This is an atomic module implementing control of the Sabertooth motor driver over packetized serial. It provides a dictionary of plaintext commands for both independent and mixed mode driving corresponding to their hexadecimal message specifications.

This is an atomic module implementing on/off control of the alarm relay, tone selection, and timed strobing. Tone selection via the setTone() method can be accomplished by numeric or string identifier; string identifiers can be used to associate tone numbers with implementation semantics. Strobing via the strobe() method spawns a threaded handler taking a list of toggle times for the alarm.

This is an atomic module consisting of on/off control of the brush motor relay, as well as an interface over simplified serial to the brush motor driver to ramp their speed using a timed thread.

This is an atomic module consisting simply of on/off control of the conveyor motor relay.

This is an atomic module consisting of a __switchState() utility method that detects the state of a given switch and any electrical faults in it. The state of the whole array is returned by the read() method only if the trigger switch is activated, and only if it had been reset prior.

This is an atomic module consisting simply of on/off control of the pump relay.

This is a test module implementing on/off control of continuous sweeping of a servomotor via varying PWM duty cycle in a threaded timer handler __servoSweep(). Sweeping is accomplished by setting specific maximum and minimum duty cycles at regular intervals. At this time there is no interface with the Lidar module, and a future one may require more sophisticated control of the servomotor position to ensure synchronicity.

This is an atomic module that registers a rising edge trigger interrupt on the any digital input, for e.g. the emergency stop button or sensing edges. Its initializer takes a list of control objects for which to call their stop() methods when the trigger event is received. The interrupt callback calls the shutdown() method until the switch is reset, which can also be called freely to ensure all attributed hardware objects are stopped.

The navigate modules are meant to include various algorithms for path planning and reactive navigation. Currently there is only one module available, the open-loop dumb controller Path

This is an atomic module taking an instance of a Drive object and implementing timer-based control of it in a threaded handler with the ability to call utility functions at the start and end of the path specification. More information is available here.

This is an atomic module that manages the interface with the IMU and calculates useful data therefrom. It relies on the RTIMULib module. When the module is initialized, it spawns a threaded handler __imuSample() that continuously reads pose data from the IMU at the ideal sampling rate. However, access to this data can be asynchronous, with the various read methods for acceleration and attitude returning appropriately converted values utilizing the latest Kalman-filtered pose. The threaded handler runs continuously until the object's go attribute is set to False.

This is an atomic module that provides an interface to read the distance from the LIDAR-Lite rangefinder. It relies on the python-smbus module for I²C communication, which is the primary dependency requiring the use of Python 2 over Python 3. It simplistically waits out the sample time rather than polling for an ACK, which a more rigorous implementation would do.

This is an atomic module that provides an interface to read the load cell in a dimensionless fashion.