A modification to revive a dead FM Towns tower model
https://townsworld.com/2021/05/08/fm-towns-tower-power-supply-assembly-guide/
Uses an Arduino PRO Micro to control power on and TownsOS power off functions just like the original power supply.
Some of the mounting holes might not be exact. At a later time, I need to measure the holes again but I don't own an original PCB anymore. It is safe to file and cut around the screw points on the outer edges.
To order a PCB, go to factory output folder and select the RAR file.
Works on the following models:
1F 2F SF SH 1H 2H 10F 20F 40H 80H SF2 SH2 CX10 CX20 CX40 CX100
It WILL NOT WORK for the following models:
S1 S2 MODEL1 MODEL2
You will need the following parts:
1 PCN13-44S-2.54DS 1 39-28-1243 or you can use 39-28-1203. It is preferred to use 39-28-1243 1 Arduino Pro Micro and Micro USB cable. You need to load the firmware for the Arduino Pro Micro 1 Some male 2.54mm pin headers. 1 Pico PSU rated at 90W or higher such as this one https://www.mini-box.com/picoPSU-90 The prototype was tested with 160W but I have found 90W is fine. Pico PSU have been cloned and their performance might vary. I recommend using the authentic mini-box brand. 1 AC/DC Converter. The board can physically fit the EPS-120-12 or the EPS-120S-12. Basically, an ACDC Converter that outputs 12V in a 2x3 or 2x4 (those are inches) form factor is fine.
日本人にとって、機械翻訳です。 あなたが困難を持っている場合は、Twitterで私に連絡してください。@cyothevile
死んだFMタウンズタワーモデルを復活させるための修正
https://townsworld.com/2021/05/08/fm-towns-tower-power-supply-assembly-guide/
Arduino PRO Microを使用して、元の電源と同様に電源オンとTownsOSの電源オフ機能を制御します。
取り付け穴の中には、正確でないものもあります。 後で、私は再び穴を測定する必要がありますが、私はもう元のPCBを所有していません。 外縁のネジ点の周りをヤスリで留めて切断しても安全です。
PCBを注文するには、工場出荷時の出力フォルダに移動し、RARファイルを選択します。
次のモデルで動作します。
1F 2F SF SH 1H 2H 10F 20F 40H 80H SF2 SH2 CX10 CX20 CX40 CX100
次のモデルでは動作しません。
S1 S2 モデル1 or Model 1 モデル2 or Model 2
次の部品が必要です。
次の部品が必要です。
1 PCN13-44S-2.54DS 1 39-28-1243 または 39-28-1203 を使用できます。 39-28-1243 を使用することをお勧めします。 1 ArduinoプロマイクロとマイクロUSBケーブル。 Arduinoプロマイクロのファームウェアをロードする必要があります 1 いくつかのオス2.54mmピンヘッダー。 1 Pico PSUは、このような90W以上で定格 https://www.mini-box.com/picoPSU-90 プロトタイプは160Wでテストされましたが、90Wは問題ありません。 Pico PSUはクローン化されており、それらのパフォーマンスは異なる場合があります。私は本物のミニボックスブランドを使用することをお勧めします。 1 AC / DCコンバータ。 ボードはEPS-120-12またはEPS-120S-12に物理的にフィットすることができます。 基本的に、2x3または2x4(これらはインチ)のフォームファクタで12Vを出力するACDCコンバータは問題ありません。
Generation 1 Tower card
- Requires more testing. Should be safe for testing.
Please follow precise instructions here: https://townsworld.com/2021/06/01/fm-towns-power-supply-generation-1/
VMS-180C-12 VOF-180C-12 VMS-200C-12
These are the recommended ACDC converters to place on the card. The Generation 1 Towers appear to use more power. A 160W Pico is recommended until further testing is completed.
ジェネレーション1タワーカード
日本人の友達、困ったら連絡してください。 [email protected]
- さらにテストが必要です。テストのために安全でなければなりません。
こちらの正確な指示に従ってください: https://townsworld.com/2021/06/01/fm-towns-power-supply-generation-1/
VMS-180C-12 VOF-180C-12 VMS-200C-12
これらは、カードに配置する推奨 ACDC コンバータです。第 1 世代のタワーは、より多くの電力を使用しているようです。 さらなるテストが完了するまでは、160W Pico をお勧めします。