Hi. I assume you compiled the fw in the download folder that has the 4 different radio firmwares for 2.3.9...

I thought this accessmod was suppose to be embedded in the otx 2.3.10, but when I flash my jumper t18pro with 2.3.10, from companion, with externalaccessmod checked, the menu’s and the functionality for r9 access, are not there..

so, would you mind, compiling a fw for 2.3.10, with the externalaccessmod, Bluetooth, lua & luac, for the jumper t18pro? Would be big help

also, do you know why, my yaapu maps, and yaapu telemetry do not work properly, with your 2.3.9 accessmod firmware?

thx

hi, before all, thanks for your great job

i do the mod and it work fine on my tx16 with 3 wires, bind access succefully, but i find that with your firmware a lost all internal multimodule telemetry. i update it with last version but still the same issue, if i put an external multimodule it work fine, and if i reflash 2.3.9 otx firmware always with the 3 wires solders it show telemetry.

and is it possible to appli access mod to a french firmware?

thanks by advance

Hi.
First thank you for you incredibly good work.
I ordered a r9m2019 with a R9MX receiver so your mod is the only way to use them on my TX16s.( No accst for the R9MX receiver.)

I have an issue with the EU 868mhz config .The radio and receiver work in 915mhz but not in 868mhz. The R9MX red light continue to rapidly flash even after I get the "bind succesfull" message. I tried both Flex and LBT firmware on the R9m2019 and MX but still not working.

Another issue is the input lag with either fport or sbus +smart port. I use a F722 wing.

Which version are you using?
I'm in europe and all my antenna are for LBT so I prefer to use 868mhz.

Thanks again for your mid and firmware.

FYI thanks

Hi.

Do you have any plans to do a 2.3.10 Version with your Access Mod?

Thanks!

Mayk

Great work on this. I purchased tx16s and R9 ACCESS module not knowing it wouldn’t works (only ACCST). I come from x-lite with RM lite pro. I use the 4 pins on r9mm for extra camera gimbal servos, and ACCESS in opentx allows me to remap those receiver pin channels and also toggle F.Port.

questions:

I saw in a git threat this code now added opentx mainline. I flashed with accessexternalmod option. Is opentx code latest best to use, or is the patch in this repo better? (Bug fixes)

Does this hardware mod loose any functionally? Like it takes up one of the external UARTS ports?

does telemetry/F.port work as expected? I saw in video demo f.port was enabled in radio UI so assume it works. I never saw example where R9 Access menu shows the pins on receiver you can remap (like using rm9 lite pro module on x-lite)

I notice screen shots for wire from board to
2 pin XJT is different from the you tube video I first found. You tube video shows soldering to one of the 5 solder joints, whilst this git shows solder to a resister pad. Is this just the same board track, or is there some variation in the tx16s internal module? Which is better? I assume one of the 5 pins stronger than risk desoldering resister.

For reference video from Rota35 here: https://youtu.be/33ehE8QtLgQ
Will add screenshot also

Wired the board up like you showed in the picture. RX to horizontal pin, TX to the vertical. Plugged in the R9M 2019 module and tried to bind, but the module doesn’t appear to be communicating. Verified my solder connections. Module seems to be blinking like it does during registration on a functioning qx7. I did notice that no firmware information is listed for the external module on the information page. Does this require any other software or specific firmware to work? I’m running R9 flex 1.30 on the module and receiver.

Hi

Thanks for your work on this. I'm really grateful I can now use ACCESS and OTA on my Jumper T16 Pro!

However, I would also like to use the (Horus) Bluetooth module I got for my Jumper T16 Pro. Would you be kind enough to please compile a version of the firmware with Bluetooth and ACCESS (+ Lua) please? I'm happy to make a contribution for your efforts.

Many thanks.

@cvetaevvitaliy

"EdgeTX" a fork of "OpenTX" is working to use this mod with their current firmware.
Are you available to help the devs get it fully working on their future builds?
Issue currently open is EdgeTX/edgetx#260

Thanks - Rich