Comments (7)
What kind of load are you using to test this? Also, what else are you using to measure the power factor?
from expandable-6-channel-esp32-energy-meter.
I put an asynchronous motor 1.1KW it gave me good results also for a 120W led lamp
and when I put a set of 2 to 3 LEDs, at the current level it's ok but for the power factor no.
I compared my measurements with a certified smart meter
from expandable-6-channel-esp32-energy-meter.
Are you able to verify the real power and apparent power (VA) of the LED lamp? The power factor can also be decreased if the current transformer is backwards.
from expandable-6-channel-esp32-energy-meter.
I tested the current sensor in both directions, always the same result !!!
Here the example :
-------------------Phase 1 : ------------------------
Voltage 1 : 218.97V
Current 1 : 0.50A
Active Power 1 : 0.109 KW
Reactive Power 1 : 0.018 KVAR
Apparent Power 1 : 0.110KVA
Power Factor 1 : 0.9870
Déphasage 1 : 0.16
Temp : 28.00°C
Frequency : 50.00Hz
-------------------Phase 2 : ------------------------
Voltage 2 : 226.38V
Current 2 : 0.33A
Active Power 2 : 0.039 KW
Reactive Power 2 : 0.065 KVAR
Apparent Power 2 : 0.075 KVA
Power Factor 2 : 0.5130
Déphasage 2 : 1.03
Temp : 25.00°C
Frequency : 49.95Hz
-------------------Phase 3 : ------------------------
Voltage 3 : 218.85V
Current 3 : 0.00A
Active Power 3 : 0.000 KW
Reactive Power 3 : 0.000 KVAR
Apparent Power 3 : 0.000 KVA
Power Factor 3 : 0.0560
Déphasage 3 : 1.51
Temp : 28.00°C
Frequency : 50.00Hz
in phase 2 instead of having 0.98 I had 0.50!
from expandable-6-channel-esp32-energy-meter.
Were you able to figure anything out with this? I assume you're reading the current for the corresponding voltage phases? If not that will also throw off the Power factor reading.
from expandable-6-channel-esp32-energy-meter.
from expandable-6-channel-esp32-energy-meter.
Hi John, That's too advanced for me. I am using the same code on github: https://github.com/CircuitSetup/Expandable-6-Channel-ESP32-Energy-Meter/blob/master/Software/ESPHome/6chan_energy_meter-add-on_jp8-jp11.yaml It worked for me, and I am getting correct values for 3 installations (3 mainboards, and 5 addons). The only problem am having is with CT8. So I don't think it is a Power factor issue.
…
On Sun, Aug 15, 2021 at 7:08 PM John @.***> wrote: We're you able to figure anything out with this? I assume you're reading the current the corresponding voltage phases? If not that will also throw off the Power factor reading. — You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub <#24 (comment)>, or unsubscribe https://github.com/notifications/unsubscribe-auth/ALTDP46RDA6IP7L3LNB4UQTT47Q6RANCNFSM4XFAYQRQ . Triage notifications on the go with GitHub Mobile for iOS https://apps.apple.com/app/apple-store/id1477376905?ct=notification-email&mt=8&pt=524675 or Android https://play.google.com/store/apps/details?id=com.github.android&utm_campaign=notification-email .
This was a different setup than yours with a 3 phase system.
from expandable-6-channel-esp32-energy-meter.
Related Issues (20)
- Help setup 6Channel Board HOT 18
- Feature Request: Add throttle_average
- Platformio Build for emonesp-nodemcu32s fails; two reasons HOT 2
- ATM90E32 not communicating ESP32C3 HOT 4
- 6Ch crash on brownout HOT 1
- Can I make a ESP8266 work with jumpers? HOT 1
- 3 Phase typo HOT 2
- 3 phase transfo board HOT 2
- AddOn Boards Power Calculation Wildly Incorrect HOT 8
- Bigger board HOT 2
- Updated files available?
- Second Voltage and Frequency Reading Zero?
- Update YAMLs to conform to Home Assistant developer guidelines? HOT 3
- CT Selection Query: Suggestions for Measuring 600A Current with ATM90E36 IC (Based on Datasheet) HOT 1
- With US split phase, simultaneous import and export is possible - small improvement to example HOT 1
- Two channels reporting erratically at certain times/conditions HOT 1
- Replacement for ESP32-DevKitC-32U, which is NRND? HOT 2
- Current Scaling Not Correct HOT 5
- esp32 wroom 32d loosing configuration details
- I see this log message after updating esphome firmware today. HOT 1
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from expandable-6-channel-esp32-energy-meter.