Failed to write pdo? about pysoem HOT 3 OPEN

Hi @buctwp,

master.slaves[0].sdo_write(0x7031, 1, struct.pack('H', 0xAAAA))

You don't write PDOs there but you do a SDO write.
The error message tells you about the issue, are you sure object 0x7031 is writable?

the return actual_wkc is 6, not 18

Why do you expect a value of 18?

from pysoem.

the address 0x7031 is read by this code

`
def read_sdo_info(ifname):

master = pysoem.Master()
master.open(ifname)
if master.config_init() > 0:
    for slave in master.slaves:
        try:
            od = slave.od
        except pysoem.SdoInfoError:
            print('no SDO info for {}'.format(slave.name))
        else:
            print(slave.name)
            for obj in od:
                print(' Idx: {}; Code: {}; Type: {}; BitSize: {}; Access: {}; Name: "{}"'.format(
                    hex(obj.index), obj.object_code,  obj.data_type,  obj.bit_length, hex(obj.obj_access), obj.name))
                for i, entry in enumerate(obj.entries):
                    if entry.data_type > 0 and entry.bit_length > 0:
                        print('  Subindex {}; Type: {}; BitSize: {}; Access: {} Name: "{}"'.format(
                            i, entry.data_type, entry.bit_length, hex(entry.obj_access), entry.name))

`

this is a part of console messages:
`
Idx: 0x7031; Code: 8; Type: 42; BitSize: 136; Access: 0x0; Name: "b'Module 4 Output Entries'"

Subindex 0; Type: 5; BitSize: 8; Access: 0x7 Name: "b'SubIndex 000'"
Subindex 1; Type: 6; BitSize: 16; Access: 0x47 Name: "b'SubIndex 001'"
Subindex 2; Type: 6; BitSize: 16; Access: 0x47 Name: "b'SubIndex 002'"
Subindex 3; Type: 6; BitSize: 16; Access: 0x47 Name: "b'SubIndex 003'"
Subindex 4; Type: 6; BitSize: 16; Access: 0x47 Name: "b'SubIndex 004'"
Subindex 5; Type: 6; BitSize: 16; Access: 0x47 Name: "b'SubIndex 005'"
Subindex 6; Type: 6; BitSize: 16; Access: 0x47 Name: "b'SubIndex 006'"
`

it seems the Index 0x7031 and subIndex 1 maps to the output: Module 4 Channel 1
so i think i can call
sdo_write(0x7031, 1, struct.pack('H', 0xAAAA)

about wkc, the code blow here:
master.send_processdata() actual_wkc = master.receive_processdata(2000) if not actual_wkc == master.expected_wkc: print('incorrect wkc, actual_wks is {}, expected_wkc is {}'.format(actual_wkc, master.expected_wkc))

the expect wkc is read from the master's property above the codes,
i have 6 slaves, when read success, counter+1, when write success, counter+2,
so if all slaves RW success, the expect wkc should be 18。

my question is how can i write output to send an Analog signal or Digital signal to the modules?
Did I send the wrong address?

from pysoem.

you are doing sdo write which is usually to assign a PDO mapping, not doing PDO communication.
to do PDO communication

input_from_slave = slave.input
slave.output = bytes([data1, data2])
master.send_processdata()
master.receive_processdata()

slave.input represent input data from slave, which is the slave send to master, it is not writeble. these data are only index's value, not include index
slave.output represent output data to slave, which is the master send to slave, you should assign a proper data to this, when master.send_processdate(), it will send these data to the slave. the data should only contain index's value.

SDO and PDO are 2 different communication way

from pysoem.