Tutorials are for informational and educational purposes only. I believe that ethical hacking, information security and cyber security should be familiar subjects to anyone using digital information and computers. I believe that it is impossible to defend yourself from hackers without knowing how hacking is done.
$ IDA Pro +7.0 (you can use Radar2 since IDA is quite expensive)
$ Router running Rompager 4.07 : there're immense number of them such as TP-Link TD-W8951*, ZyXEL P-660R, Billion BiPAC 51**/52**
$ UART to USB
The misfortune cookie vulnerability has been around for a while but still lacking an analysis which illustrate the techinical details of the vulnerability in public. According to Check Point the affected software is the embedded web server RomPager from AllegroSoft. Internet-wide scans suggest RomPager is likely the most popular web server software in the world with respect to number of available endpoints. RomPager is typically embedded in the firmware released with the device. This specific vulnerability was introduced to the code base in 2002. Moreover, the devices exposed are the one using RomPager services with versions before 4.34 (and specifically 4.07).
For this tutorial I'll be using a ZXHN H108L that uses Rompager 4.07
HTTP/1.1 401 Unauthorized
WWW-Authenticate: Basic realm="ZXHN H108L"
Content-Type: text/html
Transfer-Encoding: chunked
Server: RomPager/4.07 UPnP/1.0
EXT:
Now lets use the serial port, first we must determine the Baud rate
$ sudo stty -F /dev/ttyUSB0
OUT :
speed 115200 baud; line = 0;
-brkint -imaxbel
I use minicom, you can use anything from screen to HyperTerminal, but I prefer this one for its stability ;)
$ sudo minicom -s
+-----------------------------------------------------------------------+
| A - Serial Device : /dev/modem |
| B - Lockfile Location : /var/lock |
| C - Callin Program : |
| D - Callout Program : |
| E - Bps/Par/Bits : 115200 8N1 |
| F - Hardware Flow Control : No |
| G - Software Flow Control : No |
| |
| Change which setting? |
+-----------------------------------------------------------------------+
| Screen and keyboard |
| Save setup as dfl |
| Save setup as.. |
| Exit |
| Exit from Minicom |
+--------------------------+
Now we're good to go:
$ sudo minicom -D /dev/ttyUSB0 -b 115200
Bootbase Version: VTC_SPI1.26 | 2012/12/26 16:00:00
RAM: Size = 8192 Kbytes
Found SPI Flash 2MiB GD25Q16 at 0xbfc00000
SPI Flash Quad Enable
Turn off Quad Mode
RAS Version: ZXHN H108LV4.0.0a_ZRQ_MA
System ID: $2.12.162.0(G94.BY.2)3.20.19.0| 2014/03/21 20140321_v006 | 2014
Press any key to enter debug mode within 3 seconds.
..........
To show possible commands:
$ ATHE
======= Debug Command Listing =======
AT just answer OK
ATHE print help
ATBAx change baudrate. 1:38.4k, 2:19.2k, 3:9.6k 4:57.6k 5:115.2k
ATENx,(y) set BootExtension Debug Flag (y=password)
ATSE show the seed of password generator
ATTI(h,m,s) change system time to hour:min:sec or show current time
ATDA(y,m,d) change system date to year/month/day or show current date
ATDS dump RAS stack
ATDT dump Boot Module Common Area
ATDUx,y dump memory contents from address x for length y
ATRBx display the 8-bit value of address x
ATRWx display the 16-bit value of address x
ATRLx display the 32-bit value of address x
ATGO(x) run program at addr x or boot router
ATGR boot router
ATGT run Hardware Test Program
ATRTw,x,y(,z) RAM test level w, from address x to y (z iterations)
ATSH dump manufacturer related data in ROM
ATDOx,y download from address x for length y to PC via XMODEM
ATTD download router configuration to PC via XMODEM
ATUR upload router firmware to flash ROM
< press any key to continue >
This firmware has a set of hidden commands that are very useful to our dynamic analysis, the problem is that we can't see the registers nor set breakpoints but hopefully with these hidden commands we'd have that features, in order to see and use them we need to use ATEN. However, this command require a password, so what we can do now? let reverse engineer the firmware to find the password generator's algorithm.
(Static analysis) Let see the firmware file first:
$ binwalk ras
$ dd if=ras of=rom1.lzma bs=1 skip=85043 count=66696
$ dd if=ras of=rom2.lzma bs=1 skip=350259 count=3350556
$ lzma -d <rom1.lzma> rom1
$ lzma -d <rom2.lzma> rom2
Let see now the signature in the extracted files:
$ binwalk -Y rom1
DECIMAL HEXADECIMAL DESCRIPTION
--------------------------------------------------------------------------------
0 0x0 MIPS executable code, 32/64-bit, big endian, at least 1250 valid instructions
string is a great tool to get an idea of what a binary file is or what it contains, let see if we can find the password algorithm :
$ strings rom1 | grep -i aten
$ strings rom2 | grep -i aten
Apparently, we can't see it because the firmware is still compressed, which means we must dump it from the router using the debugging mode:
$ ATDO bfc00000, 1f0000
The first thing that comes in mind is to start looking for a dispatch table. Why? just intuition, the only alternative is if-elif but it'll be a long set of them, in order to check for the validity of the password provided by the user, and here's what I got:
ROM:800158A0 CmdTable: .word unk_80015C20 # DATA XREF: sub_8000E3D8+4C�o
ROM:800158A0 # sub_8000E3D8+90�o ...
ROM:800158A4 .word sub_8000E6D0
ROM:800158A8 .byte 0
ROM:800158A9 .byte 0
ROM:800158AA .byte 0
ROM:800158AB .byte 0
ROM:800158AC .word aJustAnswerOk # " just answer OK"
ROM:800158B0 .word aAthe # "ATHE"
ROM:800158B4 .word CMD_SHOW_HELP_ATHE
ROM:800158B8 .byte 0
ROM:800158B9 .byte 0
ROM:800158BA .byte 0
ROM:800158BB .byte 0
ROM:800158BC .word aPrintHelp # " print help"
ROM:800158C0 .word aAtba # "ATBA"
ROM:800158C4 .word CMD_ATBA
...
ROM:800158D0 .word aAten # "ATEN"
ROM:800158D4 .word CMD_ATENKeep in mind that MIPS word is 4 bytes, now let see the CMD_ATEN:
ROM:8000FF84 lw $a0, 8($s0)
ROM:8000FF88 jal sub_80013654
ROM:8000FF8C li $a1, 0
ROM:8000FF90 jal passwd_generatorand now: passwd_generator
ROM:80010A2C passwd_generator: # CODE XREF: CMD_ATEN+50�p
ROM:80010A2C lui $t9, 0xA11F
ROM:80010A30 lw $v1, ptrDO_GTABLE
ROM:80010A34 lw $t8, dword_80017050
ROM:80010A38 lw $v1, 0x18($v1) # take the seed part, generated by the ATSE command
ROM:80010A3C lbu $t8, 0x6D($t8) # take the last byte of the MAC Address
ROM:80010A40 sll $v1, 8 # $v1 = v1 << 8
ROM:80010A44 andi $t7, $t8, 7 # $t7 = t8 & 0x7
ROM:80010A48 li $t8, 0 # $t8 = 0
ROM:80010A4C srl $v1, 8 # $v1 = v1 >> 8
ROM:80010A50 li $t9, 0xA11F5AC6 # $t9 = MAGIC
ROM:80010A54 j loc_80010A68
ROM:80010A58 addu $t9, $v1, $t9 # $t9 = $v1 + $t9
ROM:80010A5C # ---------------------------------------------------------------------------
ROM:80010A5C
ROM:80010A5C loc_80010A5C: # CODE XREF: passwd_generator+40�j
ROM:80010A5C sll $t9, 31 # $t9 = $t9 << 31
ROM:80010A60 or $t9, $t6, $t9 # $t9 = $t6 | $t9
ROM:80010A64 addiu $t8, 1 # $t8 = $t8 + 1
ROM:80010A68
ROM:80010A68 loc_80010A68: # CODE XREF: passwd_generator+28�j
ROM:80010A68 sltu $t6, $t8, $t7 # $t6 = (t8 < t7? 1:0)
ROM:80010A6C bnez $t6, loc_80010A5C # take jump if $t6 != 0
ROM:80010A70 srl $t6, $t9, 1 # $t6 = $t9 >> 1
ROM:80010A74 jr $ra # all done, exit
ROM:80010A78 xor $v0, $t9, $v1 # $v0 = $t9 ^ $v1What we can conclude:
- $v1 is the seed value (generated by the ATSE command, zero if ATSE is not used)
- $t8 initially contains the last byte of MAC Address (last octet)
- 0xA11F5AC6 is the magic value we were looking for!
- Those two instructions: "$v1 = v1 << 8" and "$v1 = v1 >> 8" are equal to "seed = seed & 0x00FFFFFF"
- The loop with (sll-or-srl) is nothing more than a ROR instruction (ROR instruction on MIPS is a pseudoinstruction meaning it is typically emulated by using sll-or-srl sequence)
- $v0 is the result
Now let make a C program that does the same thing and compile it:
U32 passwd_generator(U32 seed, U8 last_mac_octet)
{
U32 b = seed & 0x00FFFFFF;
U32 r = ROR(b + 0xA11F5AC6, last_mac_octet & 7);
return r^b;
}Now let run ATSE to get the seed and use it (for instance: I got 088521A78838):
$ ./gen_pass 088521A78838
Let run the magical command we just hacked :p
$ ATEN1, A12F5AC6
ATEN1, A12F5AC6
OK
ATHE
======= Debug Command Listing =======
AT just answer OK
ATHE print help
ATBAx change baudrate. 1:38.4k, 2:19.2k, 3:9.6k 4:57.6k 5:115.2k
ATENx,(y) set BootExtension Debug Flag (y=password)
ATSE show the seed of password generator
ATTI(h,m,s) change system time to hour:min:sec or show current time
ATDA(y,m,d) change system date to year/month/day or show current date
ATDS dump RAS stack
ATDT dump Boot Module Common Area
ATDUx,y dump memory contents from address x for length y
ATWBx,y write address x with 8-bit value y
ATWWx,y write address x with 16-bit value y
ATWLx,y write address x with 32-bit value y
ATRBx display the 8-bit value of address x
ATRWx display the 16-bit value of address x
ATRLx display the 32-bit value of address x
ATGO(x) run program at addr x or boot router
ATGR boot router
ATGT run Hardware Test Program
AT%Tx Enable Hardware Test Program at boot up
ATBTx block0 write enable (1=enable, other=disable)
< press any key to continue >
ATRTw,x,y(,z) RAM test level w, from address x to y (z iterations)
ATWEa(,b,c,d) write MAC addr, Country code, EngDbgFlag, FeatureBit to flash ROM
ATCUx write Country code to flash ROM
ATCB copy from FLASH ROM to working buffer
ATCL clear working buffer
ATSB save working buffer to FLASH ROM
ATBU dump manufacturer related data in working buffer
ATSH dump manufacturer related data in ROM
ATWMx set low 6 digits MAC address in working buffer
ATMHx set hight 6 digits MAC address in working buffer
ATBS show the bootbase seed of password generator
ATLBx xmodem upload bootbase,x is password
ATSMx set 6 digits MAC address in working buffer
ATCOx set country code in working buffer
ATFLx set EngDebugFlag in working buffer
ATSTx set ROMRAS address in working buffer
ATSYx set system type in working buffer
ATVDx set vendor name in working buffer
ATPNx set product name in working buffer
ATFEx,y,... set feature bits in working buffer
ATMP check & dump memMapTab
ATDOx,y download from address x for length y to PC via XMODEM
< press any key to continue >
ATTD download router configuration to PC via XMODEM
ATUPx,y upload to RAM address x for length y from PC via XMODEM
ATUR upload router firmware to flash ROM
ATDC hardware version check disable during uploading firmware
ATLC upload router configuration file to flash ROM
ATUXx(,y) xmodem upload from flash block x to y
ATERx,y erase flash rom from block x to y
ATWFx,y,z copy data from addr x to flash addr y, length z
ATXSx xmodem select: x=0: CRC mode(default); x=1: checksum mode
ATLD Upload Configuration File and Default ROM File to Flash
ATBR Reset to default Romfile
ATCD Convert Running ROM File to Default ROM File into Flash
OK
Finally, we get a whole new set of commands that allows us to dump the memory
$ ATMP
ROMIO image start at bfc30000
code version:
code start: 80008000
code length: 1A5D4E
memMapTab: 18 entries, start = bfc44000, checksum = 9770
$RAM Section:
0: BootExt(RAMBOOT), start=80030000, len=18000
1: HTPCode(RAMCODE), start=80048000, len=E0000
2: RasCode(RAMCODE), start=80048000, len=420000
$ROM Section:
3: BootBas(ROMIMG), start=bfc28000, len=4000
4: DbgArea(ROMIMG), start=bfc2c000, len=2000
5: RomDir2(ROMDIR), start=bfc2e000, len=2000
6: BootExt(ROMIMG), start=bfc30030, len=13FD0
7: MemMapT(ROMMAP), start=bfc44000, len=C00
8: HTPCode(ROMBIN), start=bfc44c00, len=8000
(Compressed)
Version: HTP_TC V 0.05, start: bfc44c30
Length: 10488, Checksum: CB32
Compressed Length: 41CF, Checksum: D5A5
9: termcap(ROMIMG), start=bfc4cc00, len=400
10: RomDefa(ROMIMG), start=bfc4d000, len=2000
11: LedDefi(ROMIMG), start=bfc4f000, len=400
12: LogoImg(ROMIMG), start=bfc4f400, len=2000
13: LogoImg2(ROMIMG), start=bfc51400, len=2000
14: StrImag(ROMIMG), start=bfc53400, len=32000
15: StrImag2(ROMIMG), start=bfc85400, len=32000
16: Rt11nE2p(ROMIMG), start=bfcb7400, len=400
17: RasCode(ROMBIN), start=bfcb7800, len=246C00
(Compressed)
Version: ADSL ATU-R, start: bfcb7830
Length: 321D2C, Checksum: 582D
Compressed Length: 11E54B, Checksum: B30B
$USER Section:
Msecs 128
Heap0 16 300 16
Heap1 32 64 4
Heap2 64 64 4
Heap3 128 160 4
Heap4 192 256 4
Heap5 256 80 4
Heap6 320 20 4
Heap7 384 4 2
Heap8 448 20 2
Heap9 512 34 2
Heap10 1024 52 4
Heap11 2048 20 2
Heap12 3172 4 2
Heap13 4096 2 2
Heap14 0 0
...
What we just learnt will help us analysing the rom files we extracted earlier
code start: 80008000
code length: 1A5D4E
Now we can set the ROM start address and Loading address to 0x80008000 after dumping a new rom file using:
$ ATDO 80008000, 1A5D4E
We know that ATGR boot the router so what we could do is tracking it to find the instructions that passes the execution to the 2nd part of the firmware.
ROM:80011E8C loc_80011E8C: # CODE XREF: LoadAndRunImage+D8�j
ROM:80011E8C jal sub_80009B24
ROM:80011E90 li $a0, 0x1F4
ROM:80011E94
ROM:80011E94 execute_image: # execute image
ROM:80011E94 jalr $s0 # jump and link to address in $s0
ROM:80011E98 nopNow we need to ask what is the address stored at $s0? Obviously we still can't set a breakpoint, we can't view the registers so we need to leak it using some trick. Fortunately, we can read and write memory, take a look on the following command:
ATWL 80011E94, ae30001c
ATGR
From what it looks like, this command patches the instruction at 0x80011E94 with ae30001c (the byte representation of MIPS sw $s0, 0x1C($s1) instruction). By overwriting the original jalr $s0 with sw $s0, 0x1C($s1) we have forced the program to store the contents of $s0 register to 0x8001FF1C memory address. So now the second's stage firmware will not be executed instead the "ERROR" message will be presented and we will still have the access to the first stage console, Hooray! So let's take a look what was stored at 0x8001FF1C.
ATRL 8001FF1C
8001FF1C: 80020000
Gotcha! ... using 0x80020000 we can dump and properly analyse the 2nd part of the firmware
To be continued ...
React
Typescript
Django
Laravel
Facebook
Microsoft
Google
Alibaba
D3
Tencent