If the wireless device is in a bond, wavemon erroneously reports that the interfac

<a class="user-mention notranslate" data-hovercard-type="user" data-hovercard-url="/us

Can you please provide the outputs of <code class="notranslate

Of course I can, I'd love to. Thank you for your time. <div class="snippet-clipboa

😀 Thank you!! Great! Can you share what the problem was? <a target=

wavemon does not work with interface in a bond about wavemon HOT 6 CLOSED

petrkutalek commented on September 2, 2024

wavemon does not work with interface in a bond

from wavemon.

Comments (6)

grrtrr commented on September 2, 2024 1

@petrkutalek - I just made a change on master. Would you be able to test this, and also see if it addresses the misleading rfkill information?

from wavemon.

petrkutalek commented on September 2, 2024 1

Everything works perfectly, this issue can be closed. Thank you, good work.

from wavemon.

grrtrr commented on September 2, 2024

Can you please provide the outputs of

sudo rfkill list and
ip link show?

from wavemon.

petrkutalek commented on September 2, 2024

Of course I can, I'd love to. Thank you for your time.

kernel: iwlwifi 0000:00:14.3: Detected Intel(R) Wireless-AC 9560 160MHz, REV=0x318

$ wavemon -v
wavemon 0.9.3
Distributed under the terms of the GPLv3.

$ cat /etc/os-release
NAME="Arch Linux"
...

$ sudo rfkill list
0: tpacpi_bluetooth_sw: Bluetooth
	Soft blocked: no
	Hard blocked: no
1: tpacpi_wwan_sw: Wireless WAN
	Soft blocked: yes
	Hard blocked: no
2: phy0: Wireless LAN
	Soft blocked: no
	Hard blocked: no
3: hci0: Bluetooth
	Soft blocked: no
	Hard blocked: no

tpacpi_wwan_sw: Wireless WAN is Fibocom L830-EB-00 LTE WWAN Modem (2cb7:0210) PCIe M.2, interface wwp0s20f0u7

$ ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: wwp0s20f0u7: <BROADCAST,MULTICAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
    link/ether ██:██:██:██:██:██ brd ff:ff:ff:ff:ff:ff
3: wlp0s20f3: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc noqueue master bond0 state UP mode DORMANT group default qlen 1000
    link/ether ██:██:██:██:██:██ brd ff:ff:ff:ff:ff:ff permaddr ██:██:██:██:██:██
4: enp0s31f6: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
    link/ether ██:██:██:██:██:██ brd ff:ff:ff:ff:ff:ff
5: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
    link/ether ██:██:██:██:██:██ brd ff:ff:ff:ff:ff:ff

from wavemon.

petrkutalek commented on September 2, 2024

😀 Thank you!! Great! Can you share what the problem was?