When the arduino is connected to the cosmic board I cannot connect the arduino to my c

Problems with uploading to arduino and counting muons about cosmicwatch-desktop-muon-detector-v2 HOT 6 CLOSED

rbaker314 commented on July 27, 2024

Problems with uploading to arduino and counting muons

from cosmicwatch-desktop-muon-detector-v2.

Comments (6)

rbaker314 commented on July 27, 2024

You mention in the Youtube video that two of the Arduino Nano pins do not need to be connected. Do those pins need to be cut?

from cosmicwatch-desktop-muon-detector-v2.

spenceraxani commented on July 27, 2024

Hi, There are several pins on the Arduino that aren’t used at all, and they can just be left unconnected if you like. Connecting them doesn’t hurt though. Thanks, Spencer

…

On Sep 7, 2018, at 12:36 AM, rbaker314 ***@***.***> wrote: You mention in the Youtube video that two of the Arduino Nano pins do not need to be connected. Do those pins need to be cut? — You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub <#21 (comment)>, or mute the thread <https://github.com/notifications/unsubscribe-auth/ABpeuzLhZI5ja7A93f0Hm0yLg2rt80YVks5uYaNugaJpZM4WbasO>.

from cosmicwatch-desktop-muon-detector-v2.

rbaker314 commented on July 27, 2024

Since the arduino nano is not be able to communicate with a computer while on the cosmic watch board, do you have any suggestions on what I could try to remedy the problem? Thanks, Bob On Fri, Sep 7, 2018 at 3:36 AM Spencer N. Axani <[email protected]> wrote:

…

Hi, There are several pins on the Arduino that aren’t used at all, and they can just be left unconnected if you like. Connecting them doesn’t hurt though. Thanks, Spencer > On Sep 7, 2018, at 12:36 AM, rbaker314 ***@***.***> wrote: > > You mention in the Youtube video that two of the Arduino Nano pins do not need to be connected. Do those pins need to be cut? > > — > You are receiving this because you are subscribed to this thread. > Reply to this email directly, view it on GitHub < #21 (comment)>, or mute the thread < https://github.com/notifications/unsubscribe-auth/ABpeuzLhZI5ja7A93f0Hm0yLg2rt80YVks5uYaNugaJpZM4WbasO >. > — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub <#21 (comment)>, or mute the thread <https://github.com/notifications/unsubscribe-auth/AHJIgdOsEX9iUMbuAA0u2bnbEwQwIcgeks5uYkwvgaJpZM4WbasO> .

from cosmicwatch-desktop-muon-detector-v2.

jgOhYeah commented on July 27, 2024

On one of the detectors I built, I had a similar problem where the arduino connected to the computer off the muon detector board but only connected sometimes after I had soldered it to the board. I used some cheap clone arduinos and I think that maybe there was a dry joint on or around the data lines in the builtin usb connector or the usb serial converter chip on one of them. I retouched the joints around the connector and it can connect to the computer now.
I'm not sure if this will help you but it worked for me.

from cosmicwatch-desktop-muon-detector-v2.

spenceraxani commented on July 27, 2024

Hi, I’ve had a few instances where I’ve had to unplug and plug back in the Arduino, but that’s about it. If you are using a Mac, you need to have the CH340g driver installed. If you are using a Linux OS, you have to change the permissions on the port to allow it to communicate. If the Arduino IDE says that the port is in use, that means that you are already talking with it through another program (such as our import_data.py). Otherwise, perhaps there is an issue with the Arduino — although I don’t think I’ve ran into this specific problem before. I like the idea of touching up the soldering joints on the USB mini port just in case. Thanks, Spencer

…

On Sep 8, 2018, at 2:01 AM, jgOhYeah ***@***.***> wrote: On one of the detectors I built, I had a similar problem where the arduino connected to the computer off the muon detector board but only connected sometimes after I had soldered it to the board. I used some cheap clone arduinos and I think that maybe there was a dry joint on or around the data lines in the builtin usb connector or the usb serial converter chip on one of them. I retouched the joints around the connector and it can connect to the computer now. — You are receiving this because you commented. Reply to this email directly, view it on GitHub <#21 (comment)>, or mute the thread <https://github.com/notifications/unsubscribe-auth/ABpeu1NFI4Kk4tkFkjzsQpI_3nK5TJ25ks5uYwjQgaJpZM4WbasO>.

from cosmicwatch-desktop-muon-detector-v2.

rbaker314 commented on July 27, 2024

Hi,

I cut off pins connecting pins 1 and 0 of the arduino.

Still have problems connecting to arduino with computer when plugged into Micro Watch board.

Below is the error code from the arduino IDE when I try to upload the code.

Arduino: 1.8.7 (Windows 10), Board: "Arduino Nano, ATmega328P"

Sketch uses 20670 bytes (67%) of program storage space. Maximum is 30720 bytes.
Global variables use 1138 bytes (55%) of dynamic memory, leaving 910 bytes for local variables. Maximum is 2048 bytes.
C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -carduino -PCOM3 -b115200 -D -Uflash:w:C:\Users\jwise\AppData\Local\Temp\arduino_build_565452/Arduino_Code.ino.hex:i

     System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

     Using Port                    : COM3
     Using Programmer              : arduino
     Overriding Baud Rate          : 115200

avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x30
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x20
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x30
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x20
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x30
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x20
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x30
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x20
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x30
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x20

avrdude done. Thank you.

An error occurred while uploading the sketch

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.

Thanks,

Bob

from cosmicwatch-desktop-muon-detector-v2.

Problems with uploading to arduino and counting muons about cosmicwatch-desktop-muon-detector-v2 HOT 6 CLOSED

Comments (6)

Related Issues (20)

Recommend Projects

React

Vue.js

Typescript

TensorFlow

Django

Laravel

D3

Recommend Topics

javascript

web

server

Machine learning

Visualization

Game

Recommend Org

Facebook

Microsoft

Google

Alibaba

D3

Tencent