Washer-Dryer combo is missing sensors or sensors have no values about ha-smartthinq-sensors HOT 15 CLOSED

@florianmueller If you visit the affected device there is the Sensors card which lists all the enabled sensors. The last row should read something like +5 other sensors or something similar. If you expand that section, a couple of greyed-out sensors should appear. Click a sensor, than in the overlay click the cogwheel (settings) button in the top-right corner. From there you need to toggle the Enabled switch. Repeat for every sensor you want to enable.

from ha-smartthinq-sensors.

Error message now should be properly handled in last release. Related to the binary sensor Wash Completed / Dry completed, I just renamed it Run completed. There are no way to really understand if monitored device is a Washer or a Dryer and generic sensor name make more sense because in any case is related to specific device.

from ha-smartthinq-sensors.

I just tested the generic "Run completed" sensor in a notification automation, which works. My worries were that a wash and a dry cycle finish might be reported individually but that's not the case. So if I do a full wash and dry cycle I get one notification at the end of the cycle.

This cannot be managed here, at integration they are 2 different device. You can manage this at HA level using script /automation.

I haven't tested the error because my machine had no error since then. But AFAIK my detergent will run out in the next couple cycles which is reported as an error if I remember correctly. My suggestion would be to leave this issue open just as a reminder and I close it once I have seen the error sensor work?

Ok to keep this open, also because I'm doing some additional minor changes on run_completed, so you can report here if you will find some issue with next releases.
If this will auto-close means that everything is ok, but please don't comment just to avoid auto-close if there are no issue. In case you will open a new one.

Thanks.

from ha-smartthinq-sensors.

I want to report the same issue with my washer/dryer combo device. Some sensors are not getting any info, while the info is present in the app. For example these red marked sensors are all in state „unavailable“. Unfortunately also the most usful one for me „Time remaining“. Thank you for your work in this and for having a look into this!

from ha-smartthinq-sensors.

Please attach diagnostics.
Related to unavailable sensors, you just need to enable them from UI.

from ha-smartthinq-sensors.

Please attach diagnostics.

As described in this section?

Will try, although I'm on iOS so this might be slightly more complicated?

Related to unavailable sensors, you just need to enable them from UI.

I guess you are referring to @florianmueller? The states I described are definitely missing and/or not working, as described in my initial posting.

I also noticed Door Lock is missing.

from ha-smartthinq-sensors.

As described in this section?

No, just download device diagnostics on integration page and attach extracted file to this thread

I guess you are referring to @florianmueller?

Yes, second post and related image.

from ha-smartthinq-sensors.

Ah, much appreciated. Here you go @ollo69:

config_entry-smartthinq_sensors-a3a12fb60b267994a0cc37824e323f1c.json.txt

from ha-smartthinq-sensors.

Please attach diagnostics. Related to unavailable sensors, you just need to enable them from UI.

Hey @ollo69 , Thank you for your reply. I attached the diagnostics file.

Where in the UI can I enable unavailable sensors? Under the Integration settings I did not found it, also not under the device settings. Thanks!

smartthinq_sensors-1cbb3fe2f2b1c4cb6844a4aa53d8b06b-BigWash-2997a9e111cb72da881864914f825bb2.json.txt

from ha-smartthinq-sensors.

@florianmueller If you visit the affected device there is the Sensors card which lists all the enabled sensors. The last row should read something like +5 other sensors or something similar. If you expand that section, a couple of greyed-out sensors should appear. Click a sensor, than in the overlay click the cogwheel (settings) button in the top-right corner. From there you need to toggle the Enabled switch. Repeat for every sensor you want to enable.

@lukasmalkmus Thank you so much, that solved the issue for me. After enabling all 8 disabled sensors/entities and restarted HA, they all have correct values now from the dryer/washer. Awesome integration, thanks!

from ha-smartthinq-sensors.

This issue is stale because it has been open 45 days with no activity. Remove stale label or comment or this will be closed in 7 days.

from ha-smartthinq-sensors.

Nice, gonna test it out as soon as I can and report my findings.

from ha-smartthinq-sensors.

Any news here?

from ha-smartthinq-sensors.

I just tested the generic "Run completed" sensor in a notification automation, which works. My worries were that a wash and a dry cycle finish might be reported individually but that's not the case. So if I do a full wash and dry cycle I get one notification at the end of the cycle.

I haven't tested the error because my machine had no error since then. But AFAIK my detergent will run out in the next couple cycles which is reported as an error if I remember correctly. My suggestion would be to leave this issue open just as a reminder and I close it once I have seen the error sensor work?

from ha-smartthinq-sensors.

Thanks, the latest release(s) fixed everything!

I got an error because my filter was clogged and I also ran out of detergent. Both sensors triggered accordingly 🙌

Thanks for your great work!

Closing.

from ha-smartthinq-sensors.