Comments (6)
FX3 Version 2.2.0 is a very dated release. Please try v2.4.0. Are you running in a virtual machine? If so is XHCI support enabled? It would be interesting to see what is in the dmesg logs when the bladeRF 2.0 is plugged in (please power cycle after flashing FX3 firmware). It also seems like the OTP may have been wiped, if you email your serial number to [email protected] we can look up the board's calibration data.
from bladerf.
Hello and thank you for a swift reply. I will get back to you on the serial number tonight... how would I find the serial number? as i said I couldnt get any firmwares working on here so i will send the serial number as soon as i get back home from one of my jobs this evening.
from bladerf.
also p.s... no virtual machines here. Just regular computers.
from bladerf.
FX3 Version 2.2.0 is a very dated release. Please try v2.4.0. Are you running in a virtual machine? If so is XHCI support enabled? It would be interesting to see what is in the dmesg logs when the bladeRF 2.0 is plugged in (please power cycle after flashing FX3 firmware). It also seems like the OTP may have been wiped, if you email your serial number to [email protected] we can look up the board's calibration data.
hi again. I did send an email to the aformentioned email address and have not heard any reply back so far. i did install the 2.4.0 firmware which got rid of a lot of errors from the terminal readout but still the device will not initialize or open. just thought i would give an update on that.
thanks and have a good day
from bladerf.
Hi @rghilduta I ran into the same issue. But in my case I have firmware 2.4.0-git-a3d5c55f
I was able to use this device once after unpacked, but the next day I ran in to this problem.
Could you please suggest the next steps to solve/debug the issue?
Here is the full log:
$ bladeRF-cli -i -v verbose
[VERBOSE @ host/libraries/libbladeRF/src/backend/usb/libusb.c:642] Using libusb version: 1.0.25.11696
[VERBOSE @ host/libraries/libbladeRF/src/backend/usb/libusb.c:519] Found a bladeRF (idx=0)
[DEBUG @ host/libraries/libbladeRF/src/backend/usb/libusb.c:189] Bus 004 Device 010: Nuand bladeRF 2.0, serial c3935ec248074f9c8443f923ee2338b2
[VERBOSE @ host/libraries/libbladeRF/src/backend/usb/libusb.c:581] USB port reset succeeded for bladeRF c3935ec248074f9c8443f923ee2338b2
[VERBOSE @ host/libraries/libbladeRF/src/backend/usb/usb.c:106] Changing to USB alt setting 0
[VERBOSE @ host/libraries/libbladeRF/src/board/bladerf2/bladerf2.c:293] Read Firmware version: 2.4.0-git-a3d5c55f
[VERBOSE @ host/libraries/libbladeRF/src/board/bladerf2/bladerf2.c:299] Capability mask before FPGA load: 0x0000007f00000000
[VERBOSE @ host/libraries/libbladeRF/src/board/bladerf1/flash.c:401] Found SPI flash manufacturer: WINBOND.
[VERBOSE @ host/libraries/libbladeRF/src/board/bladerf1/flash.c:409] Found SPI flash device: W25Q128JV (128 Mbit).
[VERBOSE @ host/libraries/libbladeRF/src/board/bladerf1/flash.c:447] SPI flash total size = 128 Mbit
[VERBOSE @ host/libraries/libbladeRF/src/board/bladerf1/flash.c:448] SPI flash page size = 256 bytes
[VERBOSE @ host/libraries/libbladeRF/src/board/bladerf1/flash.c:449] SPI flash erase block size = 65536 bytes
[VERBOSE @ host/libraries/libbladeRF/src/board/bladerf1/flash.c:450] SPI flash number of pages = 65536
[VERBOSE @ host/libraries/libbladeRF/src/board/bladerf1/flash.c:451] SPI flash number of erase blocks = 256 pages
[VERBOSE @ host/libraries/libbladeRF/src/backend/usb/usb.c:106] Changing to USB alt setting 2
[VERBOSE @ host/libraries/libbladeRF/src/backend/usb/usb.c:106] Changing to USB alt setting 3
[DEBUG @ host/libraries/libbladeRF/src/board/bladerf2/bladerf2.c:447] Loading FPGA from: /usr/share/Nuand/bladeRF/hostedxA4.rbf
[VERBOSE @ host/libraries/libbladeRF/src/backend/usb/usb.c:106] Changing to USB alt setting 3
[VERBOSE @ host/libraries/libbladeRF/src/backend/usb/usb.c:106] Changing to USB alt setting 1
[DEBUG @ host/libraries/libbladeRF/src/backend/usb/nios_legacy_access.c:125] Failed to receive NIOS II response: Operation timed out
[DEBUG @ host/libraries/libbladeRF/src/backend/usb/nios_legacy_access.c:214] Failed to read FPGA version[0]: Operation timed out
[ERROR @ host/libraries/libbladeRF/src/board/bladerf2/bladerf2.c:122] _bladerf2_initialize: dev->backend->get_fpga_version(dev, &board_data->fpga_version) failed: Operation timed out
[ERROR @ host/libraries/libbladeRF/src/board/bladerf2/bladerf2.c:468] bladerf2_open: _bladerf2_initialize(dev) failed: Operation timed out
Failed to open device (first available): Operation timed out
from bladerf.
Just in case someone has this problem here is a solution: a16a670
Unfortunately I haven't found this in the documentation.
from bladerf.
Related Issues (20)
- test_txrx_hwloop.c / bladeRF build error on Raspberry Pi 4 B (bullseye 32bit, bookworm 64 bit) HOT 1
- BladeRF2 Micro XA4 Heating Effect
- READ CAREFULLY: BEFORE POSTING ISSUES
- bladeRF 2.0 micro xA4 behaving erratically when sampling rate is just changed
- fx3_gpif entity error HOT 17
- RuntimeError: bladerf_common::set_clock_source: Failed to set VCTCXO tamer mode: Operation not supported (-8) HOT 1
- Impossible to get 122 MSp/s samplerate on BladeRF xA4 with no signal interruptions HOT 1
- Creating rbf file to blink leds on Bladerf A4
- Synchronization of TX and RX Signals in BladeRF 2.0 xA9 HOT 7
- missing trigger functionality api's in bladerf python binding
- Micro phase coherence for four channel HOT 1
- segfault in bladeRF-cli when compiled from latest master (2fbae2c38b377cfbee98c281789cd43d1f1b55e4) HOT 1
- bladeRF-cli Segmentation fault HOT 2
- bladerf_get_gain_modes implemented inconsistently between bladeRF1 and bladeRF2.
- Windows installer link results in a 404 not found HOT 2
- Problem instaling Mac OSX HOT 9
- Fix Argument Order in calloc Call in fir_filter.c HOT 1
- Update PPA HOT 1
- Below are my query on BladeRF regarding API to get the response HOT 1
- Not able to plot IQ data received from bladerf -cli command received sample.csv file.
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from bladerf.