Comments (3)
lars721
commented on August 17, 2024
Hi fritzi-blizi,
this sounds good that YCast works with your Technics Ottava. I will also try with my Technics ST-C700D.
Seems that both had similar Firmware changes in the relation to vTuner issues in the past.
Hopefully they have similar firmware for vTuner included.
I am not sure about the correct vTuner URL because Wireshark shows me as last network commands when trying to reach the Server for using "Internet Radio" a ping to IP 75.126.133.179 with no answer.
Destination of that IP is in US - a service provider of vTuner company.
I will try to build up my own DNS server to reconnect my player towards YCast server. But I am not familar with this.
And be careful to not install the new firmware released by Technics on January, 10 th 2023 !!
It will delete the complete Internet Radio functionality of your Technics Network Player !!!!
Lars
from ycast.
fritzi-blizi
commented on August 17, 2024
Hi Lars,my YCAST server runs great with my Technics SC-C70. The site is technics.vtuner.com . Thanks for the software!The receiver looks for a second address in Japan for new firmware. I blocked this query with Pi-Hole on the Raspberry server. Now i have no longer a update information on the display..A site in the Nederland describes, how yo can built up a complete server with Pi-Hole and so on. http://alriklubbers.com/2020/02/22/install-vtuner-alternative-alongside-pi-hole/ It was for me a little bit easier and complete…It is a big mess, that Technics destroys a function of the receiver with a software update!Best regardsHans-HermannVon meinem iPad gesendetAm 12.01.2023 um 20:38 schrieb lars721 ***@***.***>:
Hi fritzi-blizi,
this sounds good that YCast works with your Technics Ottava. I will also try with my Technics ST-C700D.
Seems that both had similar Firmware changes in the relation to vTuner issues in the past.
Hopefully they have similar firmware for vTuner included.
I am not sure about the correct vTuner URL because Wireshark shows me as last network commands when trying to reach the Server for using "Internet Radio" a ping to IP 75.126.133.179 with no answer.
Destination of that IP is in US - a service provider of vTuner company.
I will try to build up my own DNS server to reconnect my player towards YCast server. But I am not familar with this.
And be careful to not install the new firmware released by Technics on January, 10 th 2023 !!
It will delete the complete Internet Radio functionality of your Technics Network Player !!!!
Lars
—Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you authored the thread.Message ID: ***@***.***>
from ycast.
lars721
commented on August 17, 2024
Yes! Successfully installed Internet Radio for my Technics ST-C700D too.
I used the pdf file instruction found here in AVForum https://www.avforums.com/threads/vtuner-internet-radio-stop-working-marantz-denon-3-case.2269858/page-8#post-29660484
- I used my already installed raspberry pi. It had already a static IP address fixed in my Router. No need to change any DHCP settings on the raspberry. (My Technics has connected network wire and no Wifi !)
- installed dnsmasq and dnsutils
- add entry: address=/vtuner.com/192.168... (local IP address of my Raspberry) in file dnsmasq.conf
- installed YCast
- Changed network settings on my Technics player: DHCP off, fixed IP address, Gateway IP of my router, first DNS server (IP address of my RaspberryPi) (the pdf instruction pointed to change the secondary DNS server address, but this didn't worked for my Technics
I assume that YCast should work with all following Technics models: SU-G30, ST-C700D, SC-C500, SU-C550, SC-C70
from ycast.
Related Issues (20)
- Confirmed working on Marantz SB6009
- Confirmed working on Yamaha HT-4066
- Confirmed working on Marantz M-CR511 HOT 3
- What is roughly needed to implement the bookmark functionality? HOT 2
- Ycast
- How to create a manual entry in your DNS server? HOT 2
- Ycast Failure With Aluratek AIRMM01F Internet Clock/Radio HOT 2
- Problem with install ycast on router keenetic HOT 2
- Confirmed working on Marantz NA7004
- Ycast with Cabasse wireless speaker not working HOT 2
- Marantz NR-1504 is also supported
- Stream station image not loaded
- installation help HOT 4
- Always a 404 result HOT 4
- Noxon 2 Audio, not working
- Pi-Hole setup for Yamaha ycast HOT 1
- No retry if the randomly picked server all.api.radio-browser.info fails. HOT 7
- Grundig Sonoclock 890A-Web fails reading the station list HOT 3
- Confirmed working Marantz NR-1604 and NR-1607
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from ycast.