Cant get Getting started working about rf24 HOT 6 OPEN

Sorry, no.  If the wires are hooked up correctly, and the modules are functioning correctly, this will always work.

----- Original Message -----
From: Ardidrones [email protected]
To: maniacbug [email protected]
Cc:
Sent: Sunday, July 22, 2012 1:11 AM
Subject: [RF24] Cant get Getting started working (#9)

Hi Guys

I have a few of these units lying at home and cant get them to work , I found this site lastweek and have been trying to get the” getting started” example working but with no luck, checked all the wires 4 times made all the libraries local in the Pde to try cancel out file path issues , but still nothing when i start the serial monitor next to all the Config print lines I get 0xff so it seesm like the radio doesnt int. properly . any ideas?

Reply to this email directly or view it on GitHub:
#9

from rf24.

Why would you define them as 9,10 then in the software

Please safe our environment and do not print this email.

On Jul 22, 2012, at 21:47, [email protected] wrote:

Sorry, no. If the wires are hooked up correctly, and the modules are functioning correctly, this will always work.

----- Original Message -----
From: Ardidrones [email protected]
To: maniacbug [email protected]
Cc:
Sent: Sunday, July 22, 2012 1:11 AM
Subject: [RF24] Cant get Getting started working (#9)

Hi Guys

I have a few of these units lying at home and cant get them to work , I found this site lastweek and have been trying to get the” getting started” example working but with no luck, checked all the wires 4 times made all the libraries local in the Pde to try cancel out file path issues , but still nothing when i start the serial monitor next to all the Config print lines I get 0xff so it seesm like the radio doesnt int. properly . any ideas?

---

Reply to this email directly or view it on GitHub:
#9

---

Reply to this email directly or view it on GitHub:
#9 (comment)

from rf24.

Because the Getting Started blog posts instructs to hook up lines 9 & 10 to CE & CSN.

----- Original Message -----
From: Ardidrones [email protected]
To: maniacbug [email protected]
Cc:
Sent: Sunday, July 22, 2012 12:55 PM
Subject: Re: [RF24] Cant get Getting started working (#9)

Why would you define them as 9,10 then  in the software

Please safe our environment and do not print this email.

On Jul 22, 2012, at 21:47, [email protected] wrote:

Sorry, no.  If the wires are hooked up correctly, and the modules are functioning correctly, this will always work.

----- Original Message -----
From: Ardidrones [email protected]
To: maniacbug [email protected]
Cc:
Sent: Sunday, July 22, 2012 1:11 AM
Subject: [RF24] Cant get Getting started working  (#9)

Hi Guys

I have a few of these units lying at home and cant get them to work , I found this site lastweek and have been trying to get the” getting started” example working but with no luck, checked all the wires 4 times made all the libraries local in the Pde to try cancel out file path issues , but still nothing when i start the serial monitor next to all the Config print lines I get 0xff so it seesm like the radio doesnt int. properly . any ideas?

---

Reply to this email directly or view it on GitHub:
#9

---

Reply to this email directly or view it on GitHub:
#9 (comment)

Reply to this email directly or view it on GitHub:
#9 (comment)

from rf24.

Okay thanx , I have followed your blog even to the colors of wires you used but I can get it to work they why you do , where can I start testing if my units isn't maybe faulty ? I hope they not but you never know with china .

Please safe our environment and do not print this email.

On Jul 22, 2012, at 22:16, [email protected] wrote:

Because the Getting Started blog posts instructs to hook up lines 9 & 10 to CE & CSN.

----- Original Message -----
From: Ardidrones [email protected]
To: maniacbug [email protected]
Cc:
Sent: Sunday, July 22, 2012 12:55 PM
Subject: Re: [RF24] Cant get Getting started working (#9)

Why would you define them as 9,10 then in the software

Please safe our environment and do not print this email.

On Jul 22, 2012, at 21:47, [email protected] wrote:

Sorry, no. If the wires are hooked up correctly, and the modules are functioning correctly, this will always work.

----- Original Message -----
From: Ardidrones [email protected]
To: maniacbug [email protected]
Cc:
Sent: Sunday, July 22, 2012 1:11 AM
Subject: [RF24] Cant get Getting started working (#9)

Hi Guys

I have a few of these units lying at home and cant get them to work , I found this site lastweek and have been trying to get the” getting started” example working but with no luck, checked all the wires 4 times made all the libraries local in the Pde to try cancel out file path issues , but still nothing when i start the serial monitor next to all the Config print lines I get 0xff so it seesm like the radio doesnt int. properly . any ideas?

---

Reply to this email directly or view it on GitHub:
#9

---

Reply to this email directly or view it on GitHub:
#9 (comment)

---

Reply to this email directly or view it on GitHub:
#9 (comment)

---

Reply to this email directly or view it on GitHub:
#9 (comment)

from rf24.

Hi maniacbug

I keep getting a EEPROM_update not declared when I try compile sensor net . Any idea?

Thanx for any help

Please safe our environment and do not print this email.

from rf24.

First and for most. Thank you for all your work on this. I have configured two boards just like your site says on http://maniacbug.wordpress.com/2011/11/02/getting-started-rf24/ . Get them both started and both on the monitor so I can see the status. At this point I press "t" on my Monitor of Com4. It reports that it is Failing. I toggle com 4 back by pressing "r". I press "t" on my Monitor of Com3 and I start to get a good result. Now if I toggle com3 back with a "r" and toggle Com4 to "t"...it works good now.

from rf24.