Comments (19)
PassiveLemon
commented on July 21, 2024
1
I Initially had this problem too. I eventually got the file size down to around 226 KB but it would still produce the error.
If you've already tried to flash firmware multiple times, flash official firmware first and then your custom one after. I found that doing this actually solved my problem.
There's a neat guide here on reducing firmware size: https://www.crosslink.io/2020/08/14/shrinking-marlin-2-0-how-to-reduce-firmware-size-for-8-bit-boards-and-still-use-a-bltouch-and-the-filament-sensor/
from sv06.
hillsoftware
commented on July 21, 2024
Assuming you don't have any issues with the bed wiring (which you can verify by flashing back to the Sovol version and seeing if it works), I would say it is a bad flash.
from sv06.
j-lang
commented on July 21, 2024
When I flash the firmware with UBL, the printer starts beeping and shows an error about Bed Temperature.
How can I fix it? Using latest version from Releases Page with UBL
Which version did you build? I can confirm the same behavior with V60b code/config compiled with PlatformIO. Switched back to V60 binary.
from sv06.
hillsoftware
commented on July 21, 2024
If you are building your own binary and having this issue, check the bin file size. If it is over 228K than that is probably your issue. The GD processor Sovol uses on their board is a "clone" of the Arm processor and it has some issues.
The latter 256K of the flash space runs slower than the first half and any code in it causes unpredictable results. So you only have the first 256K and 28K of it is used by the bootloader.
So if you are having issues like described above, check your bin file size.
from sv06.
j-lang
commented on July 21, 2024
The bin file has a size of 262.372 bytes. How can the bin file size reduced. Used the platformIO setting from this repo?
from sv06.
hillsoftware
commented on July 21, 2024
I build on a Linux system. I don't know if that is why my binaries are smaller than others. I use PlatformIO and VS Code on Linux.
If you can't sort the compiler differences you could turn off any un-needed stuff to reduce size. Much easier to do on non UBL builds.
from sv06.
jenkinsmichpa
commented on July 21, 2024
I built on Linux system with PlatformIO 6.1.6 in VSCode and had a similar binary size to j-lang/printer temp warnings. I installed it today so it might have pulled a newer library version than the original compilation or something similar.
from sv06.
kdobrev
commented on July 21, 2024
Do you think if we comment all libraries for the different screens that get compiled we can save some space?
For example idk which of these are really in use:
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_arduino_st7920_custom.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_arduino_st7920_hw_spi.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_arduino_st7920_spi.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_arduino_std_sw_spi.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_arduino_sw_spi.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_arduino_t6963.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_arduino_uc_i2c.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_atmega_hw_spi.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_atmega_parallel.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_atmega_st7920_hw_spi.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_atmega_st7920_spi.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_atmega_sw_spi.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_atxmega_hw_spi.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_atxmega_st7920_hw_spi.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_esp32_ssd_i2c_fn.cpp.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_i2c.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_io.cpp.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_linux_ssd_i2c.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_msp430_hw_spi.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_null.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_psoc5_ssd_hw_parallel.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_raspberrypi_hw_spi.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_raspberrypi_ssd_i2c.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_samd51_hw_spi.cpp.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_samd51_st7920_hw_spi.cpp.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_std_sw_spi.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_stm32duino_hw_spi.cpp.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_com_stm32duino_ssd_i2c.cpp.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_cursor.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_delay.cpp.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_a2_micro_printer.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_flipdisc_2x7.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_gprof.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ht1632.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ili9325d_320x240.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ks0108_128x64.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_lc7981_160x80.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_lc7981_240x128.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_lc7981_240x64.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_lc7981_320x64.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ld7032_60x32.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_null.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_pcd8544_84x48.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_pcf8812_96x65.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_sbn1661_122x32.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ssd1306_128x32.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ssd1306_128x64.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ssd1306_64x48.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ssd1309_128x64.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ssd1322_nhd31oled_bw.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ssd1322_nhd31oled_gr.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ssd1325_nhd27oled_bw.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ssd1325_nhd27oled_bw_new.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ssd1325_nhd27oled_gr.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ssd1325_nhd27oled_gr_new.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ssd1327_96x96_gr.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ssd1351_128x128.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_ssd1353_160x128.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_st7565_64128n.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_st7565_dogm128.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_st7565_dogm132.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_st7565_lm6059.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_st7565_lm6063.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_st7565_nhd_c12832.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_st7565_nhd_c12864.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_st7687_c144mvgd.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_st7920_128x64.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_st7920_192x32.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_st7920_202x32.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_t6963_128x128.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_t6963_128x64.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_t6963_240x128.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_t6963_240x64.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_tls8204_84x48.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_uc1601_c128032.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_uc1608_240x128.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_uc1608_240x64.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_uc1610_dogxl160.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_uc1611_dogm240.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_uc1611_dogxl240.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_uc1701_dogs102.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_dev_uc1701_mini12864.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_ellipse.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_font.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_font_data.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_font_data_04b.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_font_data_courier.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_font_data_fu.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_font_data_gd.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_font_data_helvetica.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_font_data_ncen.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_font_data_os.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_font_data_profont.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_font_data_symb.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_font_data_times.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_font_data_unifont.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_line.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_ll_api.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_page.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pb.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pb14v1.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pb16h1.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pb16h2.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pb16v1.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pb16v2.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pb32h1.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pb8h1.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pb8h1f.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pb8h2.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pb8h8.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pb8v1.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pb8v2.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pbxh16.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_pbxh24.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_polygon.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_rect.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_rot.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_scale.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_state.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_u16toa.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_u8toa.c.o
Compiling .pio\build\GD32F103RET6_sovol_maple\libf30\U8glib-HAL\clib\u8g_virtual_screen.c.o```
Or the lines for this folder Compiling .pio\build\GD32F103RET6_sovol_maple\lib35e\USBComposite
And by the way on Windows mine got 245 KB (251 740 bytes)
from sv06.
kdobrev
commented on July 21, 2024
I installed Fedora and copiled it there - the image is 251.4 kB (251,372 bytes) now.
So it is not the OS that makes it bigger.
from sv06.
Devirex
commented on July 21, 2024
Hi, i have just build the V57 source code, and i run into the same issue. After building on Windows and Linux, filesize with UBL is 272 KB.
Advanced Memory Usage is available via "PlatformIO Home > Project Inspect"
RAM: [=== ] 32.0% (used 20960 bytes from 65536 bytes)
Flash: [===== ] 53.1% (used 278236 bytes from 524288 bytes)
Building .pio/build/GD32F103RET6_sovol_maple/firmware-20240103-000629.bin
Are there any optimizations that can be done to reduce the filesize?
from sv06.
slablaadje
commented on July 21, 2024
I'm also running into the same issues but can't seem to fix it. Even installing the official firmware first and then my file, but then again it is bigger than 228kB so maybe it needs to be AND <228kB AND installed right after the official firmware was put on it.
Can you tell me how you achieved 226kB? I'm stuck on 246kB even after disabling a whole bunch of that link.
from sv06.
PassiveLemon
commented on July 21, 2024
All my current changes are here. Some people seem to get better results than others and I'm not sure why.
In summary:
Disabled the boot screen and status screen
Disabled EEPROM_CHITCHAT
Disabled PLR
Enabled SD_CARD_READONLY
Disabled the beeper
from sv06.
slablaadje
commented on July 21, 2024
All my current changes are here. Some people seem to get better results than others and I'm not sure why. In summary: Disabled the boot screen and status screen Disabled EEPROM_CHITCHAT Disabled PLR Enabled SD_CARD_READONLY Disabled the beeper
Am I correct in understanding you are not on hillsoftware's version but on sovol3d's fork and also experienced the issue? I disabled even more than you did but still am on 248kB.
from sv06.
PassiveLemon
commented on July 21, 2024
Yep, I am forked directly off the official repo
from sv06.
slablaadje
commented on July 21, 2024
Right that is to no avail for me then, as I really want the 2.1.x / hillsoftware. Then it's a dead end for me to compile it myself, I tried all day to flash it, get it smaller. Unless anyone is willing to compile the UBL v57 with one change in the config:
#define HOLD_MULTIPLIER 0.5
into
#define HOLD_MULTIPLIER 1
As I have some steppers that don't like the low currents.
from sv06.
slablaadje
commented on July 21, 2024
To stay under 228kB, I decided to take the latest marlin bugfix-2.1.x branch, and merge the settings from the sv06 repo here into it, and applied my personal changes. And I had to disable a whole lot, but I was able to keep all the (for me) necessary and useful features luckily!
I am not going to make a new repo as it is very custom for me, and I even disabled the bootscreen.
If you too want to go this route, I'd say come to the unofficial sovol discord and we can help you out there.
@hillsoftware any thoughts on this or the future of your repository?
from sv06.
gittyeric
commented on July 21, 2024
+1 same error after flashing, and my compiled size on an Ubuntu machine is 263Kb. Curious 228K limit is a hard one or just unstable for some?
from sv06.
slablaadje
commented on July 21, 2024
I have done some more digging, in chronological order
- got bugfix 2.1.x to flash by applying a lot of cost savings in marlin features
- bugfix 2.1.x had bad print quality for me
- went back to michael hill's branch of marlin, and applied same cost savings
- flashing a 226kB .bin worked
- but then it didnt, and also my other sovol has similar issues with the GD32 chip
- i bought a new board with STM32 chip
- no issues whatsoever with flashing anymore
from sv06.
mattordev
commented on July 21, 2024
Hey all, just ran into this issue myself. Going to try and flash default Sovol firmware and then my compiled attempt and see how that goes! Instead posting multiple comments, I'll just keep it in one comment :)
- Flashed most up to date Sovol provided firmware (229kb)
- Made minor tweaks to configs for v57, mainly just disabling driver monitoring as I'm trying to fix another issue
- Flashed new built firmware, using v57 provided configs (255kb)
- Printer beeps and screams at me like a tiny insect :(
What I have observed though, for me, its E1, not my bed that's throwing the thermal runaway. Not sure if it's due to it just getting to that sensor first but odd none the less. I even tried unplugging the entire extruder (so, in theory E1 can't thermally runaway) and it still throws the error.
To chip in to the space saving thing, surely we shouldn't have to disable anything if things were working correctly, no? I'm not sure if @hillsoftware had to do any space saving but from what I can tell the precompiled releases (v57, ..., ...) are all full of features so we're missing something here.
@hillsoftware, can you try and intentionally bloat one of your binaries and flash it and see if you get the same error? Hell I'll even flash it for you if you'd like.
Well, this has beaten me for now! So off to bed I go.
from sv06.
Related Issues (19)
- Printer gets stuck same place HOT 4
- Printer gets stuck HOT 4
- #define SPEAKER macro HOT 3
- bin-files for 60b HOT 1
- Blank blue screen after flashing firmware HOT 6
- Probign failed during UBL wizard. HOT 1
- Media Init Fail HOT 1
- M601 ignored HOT 2
- Sensorless Homing HOT 3
- Switching to Marlin bugfix instead of this repo? HOT 2
- Printer Homing Forward on Y Axis HOT 2
- updat ein PlatformIO and marlin code couses error during compilation
- Printer Crashes when Running Bilinear Leveling after Running X-Twist Compensation HOT 1
- sv06 ignores bounds when probing pre-print HOT 1
- I want to use UBL with Sovol SV06, where is Rory's video? HOT 2
- Homing issue HOT 6
- No issue, just a question. HOT 1
- False positive HOT 1
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from sv06.