Give webui a title and make it configurable about esp-knx-ip HOT 9 OPEN

// KNX WebPage Configuration
// -------------------------

// The order of the knx.***_register_*** code, is the order shown on the web page.

knx.config_register_WebPageTitle("KNX Configuration");

knx.config_register_Title("KNX Parameters");

knx.config_register_line();

knx.config_register_SubTitle("General");

// Names to be displayed on the Physical Address Object. So, translations can be done by the main program
knx.config_register_pa("Physical Address","Set");

// (optional) Set Physical KNX Address of the device
knx.physical_address_set(knx.PA_to_address(1, 1, 1));

knx.config_register_label("(must be unique on the KNX Network)");

knx.config_register_blankspace();

if (Settings.flag.knx_enabled) {
  // On the feedback_register_action can be defined the names to display.
  // knx_disable_pressed is a callback that uses enable_knx_id to call
  // feedback_set_action and modify that feedback action
  enable_knx_id = knx.feedback_register_action("KNX: Enabled", "Disable", knx_disable_pressed);
}
else {
  enable_knx_id = knx.feedback_register_action("KNX: Disabled", "Enable", knx_enable_pressed);
}

knx.config_register_line();

knx.config_register_SubTitle("Send Data to Group Addresses");

// Register Group Addresses to Send Data to
Relay[0].status_ga_id = knx.config_register_ga("Relay 1 Status", &Relay[0].enabled, "Add"); // "Add" is the text on the Group Address button. True is the Enable/Disable of that Address
Relay[1].status_ga_id = knx.config_register_ga("Relay 2 Status", &Relay[1].enabled);
Relay[2].status_ga_id = knx.config_register_ga("Relay 3 Status", &Relay[2].enabled);
Relay[3].status_ga_id = knx.config_register_ga("Relay 4 Status", &Relay[3].enabled);
Button[0].status_ga_id = knx.config_register_ga("Button 1 Status", &Button[1].enabled);
Button[1].status_ga_id = knx.config_register_ga("Button 2 Status", &Button[2].enabled);
Button[2].status_ga_id = knx.config_register_ga("Button 3 Status", &Button[3].enabled);
Button[3].status_ga_id = knx.config_register_ga("Button 4 Status", &Button[4].enabled);
sensor_temp.ga_id = knx.config_register_ga("Temperature", true);

// (optional) Set Group Addresses to Send Data to
knx.config_set_ga(Relay[0].status_ga_id, knx.GA_to_address(2,2,1));
Relay[0].enabled = true;
knx.config_set_ga(sensor_temp.ga_id, knx.GA_to_address(4,1,1));

knx.config_register_blankspace();

label_test_send_Relay1 = "Relay 1 Status: " + Relay[0].state ? "ON" : "OFF";
knx.feedback_register_action(&label_test_send_Relay1, send_data, "Test Send"); // "Test Send" is the text of the button. label_test_send_Relay1 is going to be updated on void loop()
                                                                               // all feedback action buttons are yellow as warning because they execute things
label_test_send_temp = "Temperature (°C): " + last_temp;
knx.feedback_register_action(&label_test_send_temp, send_data, "Test Send"); // "Test Send" is the text of the button. label_test_send_temp is going to be updated on void loop()

knx.config_register_blankspace();

Relay[0].update_rate_id = knx.config_register_int("Relay 1 Status Update rate (ms)", UPDATE_INTERVAL_RELAY, "Set"); // "Set" is the text on the button
sensor_temp.update_rate_id = knx.config_register_int("Relay 1 Status Update rate (ms)", UPDATE_INTERVAL, "Set"); // "Set" is the text on the button

knx.config_register_label("Set Update Rate to 0 ms for not sending regular updates.");
knx.config_register_label("Updates will be sent only for relay toggle or button press");

knx.config_register_line();

knx.config_register_SubTitle("Receive Data from Group Addresses");

// Register Group Addresses to Receive data from and execute callbacks
Relay[0].callback_id = knx.callback_register("Toggle Relay 1", relay_cb, &Relay[0], &Relay[0].enabled_cb, "Add");
Relay[1].callback_id = knx.callback_register("Toggle Relay 2", relay_cb, &Relay[1], &Relay[1].enabled_cb);
Relay[2].callback_id = knx.callback_register("Toggle Relay 3", relay_cb, &Relay[2], &Relay[2].enabled_cb);
Relay[3].callback_id = knx.callback_register("Toggle Relay 4", relay_cb, &Relay[3], &Relay[3].enabled_cb);
sensor_temp.callback_id = knx.callback_register("Reply Temperature", reply_temp_cb, &sensor_temp, &sensor_temp.enabled_cb);

// (Optional) Set Group Addresses to receive Data from
knx.callback_assign(Relay[0].callback_id, knx.GA_to_address(2,2,1));
Relay[0].enabled_cb = false; // Disabled GA. will not call the callback. Because it has a registered address is going to be shown on the page.
                             // Disabled GA shows the yellow enable button to activate again the use of the callback
knx.callback_assign(sensor_temp.callback_id, knx.GA_to_address(4,1,1));
sensor_temp.enabled_cb = true;

knx.config_register_blankspace();

label_test_action_Relay1 = "Toggle Relay 1 (Actual: " + Relay[0].state ? "ON)" : "OFF)";
knx.feedback_register_action(&label_test_action_Relay1, relay_cb_1, "Test Action"); // "Test Action" is the text of the button.

label_test_action_temp = "Reply Temperature (" + last_temp + " °C)";
knx.feedback_register_action(&label_test_action_temp, reply_temp_cb, "Test Action"); // "Test Action" is the text of the button. label_test_send_temp is going to be updated on void loop()

knx.config_register_line();

knx.feedback_register_custom_button("Save", KNXSaveSettings); // KNXSaveSettings is a subroutine on the main program. custom_button are yellow
knx.feedback_register_return_button("Return", "/"); // "/" is the address to return.

// END KNX WebPage Configuration

typedef struct __config_webUI
{
  const char *WebPageTitle;
  const char *PhysAddrLabel;
  const char *Set;
  const char *Add;
  const char *Delete;
} config_webUI_t;

// Web Page Translations
#define D_CONFIGURE_KNX "Configure KNX"
#define D_KNX_PARAMETERS "KNX parameters"
#define D_KNX_GENERAL_CONFIG "General"
#define D_KNX_PHYSICAL_ADDRESS "Physical Address"
#define D_KNX_SET "Set"
#define D_KNX_ADD "Add"
#define D_DELETE "Delete"
#define D_REPLY "Reply"
#define D_KNX_PHYSICAL_ADDRESS_NOTE "(Must be unique on the KNX network)"
#define D_KNX_GROUP_ADDRESS_TO_WRITE "Group Addresses to Send Data to"
#define D_KNX_GROUP_ADDRESS_TO_READ "Group Addresses to Receive Data from"
#define D_KNX_PARAMETER_TO_SEND "Parameter to Send"
#define D_KNX_UPDATE_INTERVAL "Sensor Update Interval (sec)"

// Translations
config_webUI_t config_webUI = {
  D_CONFIGURE_KNX,
  D_KNX_PHYSICAL_ADDRESS,
  D_KNX_SET,
  D_KNX_ADD,
  D_DELETE
};

// KNX WebPage Configuration
// -------------------------
// The order of the knx.***_register_*** code, is the order that is going to be shown on the web page.

// Translations
knx.config_web_UI(config_webUI);

knx.config_register_Title( D_KNX_PARAMETERS );

knx.config_register_line();

//Set Physical KNX Address of the device
knx.config_register_pa(); // to position physical address config at top of page
knx.physical_address_set(knx.PA_to_address(1, 1, 1));

knx.config_register_label( D_KNX_PHYSICAL_ADDRESS_NOTE );

knx.config_register_blankspace();

knx.feedback_register_action("KNX: " D_ON, knx_toggle_flag_enabled, D_STOP, nullptr, knx_status_enabled);
knx.feedback_register_action("KNX: " D_OFF, knx_toggle_flag_enabled, D_START, nullptr, knx_status_disabled);

knx.config_register_line();

knx.config_register_SubTitle( D_KNX_GROUP_ADDRESS_TO_WRITE );

// Register Group Addresses to Send Data to
for (int i = 0; i < Settings.knx_Registered_GA; ++i)
{
  if (device_param[i].show)
  {
    device_param[i].id = knx.config_register_ga(String(device_param[i].name));
    knx.config_set_ga(device_param[i].id, Settings.knx_GA_addr(i));
  }
}

knx.config_register_blankspace();

update_rate_id = knx.config_register_int( D_KNX_UPDATE_INTERVAL , Settings.knx_update_rate);

knx.config_register_line();

knx.config_register_SubTitle( D_KNX_GROUP_ADDRESS_TO_READ );

// Register Group Addresses to Receive data from and execute callbacks
for (int i = 0; i < Settings.knx_Registered_CB; ++i)
{
  if (device_param[i].show)
  {
    cb_conf_id = knx.callback_register( String( device_param_cb[i] ), action_cb, &device_param[i]);
    //////buscar en la config el param para setearlo
    //knx.callback_assign(ga_conf, Settings.knx_CB_addr(i));
    if (i==0)
    {
      //knx.callback_assign(cb_conf_id, knx.GA_to_address(2,2,1));
    }
  }
}

knx.config_register_line();

knx.feedback_register_action("", KNXSaveSettings, D_SAVE); // Save Button

knx.feedback_register_action("", KNX_Return_button, D_CONFIGURATION); // return to previous configuration menu

// END KNX WebPage Configuration