LVM VDO not sending "device online events" to LVM ? about vdo HOT 5 OPEN

Hi @tigerblue77, I saw this thread and meant to reply sooner.

I'm still trying to understand what might be going on for you, but wanted to mention that all of the mount options that you listed for the /etc/fstab are not actually needed in the LVM-VDO (or RHEL-8.3+) scenario. We're working to update the docs on that. But you should be able to get away with a basic configuration that looks like:

echo "$DM_VDOLV_PATH	$MOUNT_POINT	ext4	defaults	0	0" >> /etc/fstab

The need for the additional options previously was because we only had the vdo.service unit which effectively ran vdo start --all and we didn't have any per-volume control. We have since established a udev trigger that runs an instantiated systemd unit that can start individual volumes as their storage becomes available.

This behavior has always been present for the LVM-VDO implementation, and I'm a little confused on the need for a lvm2-activation-generator. Prior to us being acquired by Red Hat, we had a number of Debian/Ubuntu deployments that seemed to work fine, but perhaps things have changed over the last few years?

from vdo.

Hi @rhawalsh,

Thanks for taking a look and thanks for your reply. I am currently working on this project, so I will modify my script with your suggestion and tell you directly if it works for me.

Edit: yes it works. Thanks.

Don't worry, it works like a charm once I add the configuration line event_activation = 0 in the LVM configuration file (/etc/lvm/lvm.conf). I'm just curious, which is why I'm wondering:

• Why do I need this systemd .mount file? I was thinking that /etc/fstab was the only configuration needed for permanent/static mounts and the system was dealing with it.
• Why is all this manipulation not necessary when creating "basic" logical volumes? VDO is just build on top of LVM so it should act the same... Especially since my VDO volumes are active when I create them.
• Why do I have to keep this event_activation parameter in my lvm.conf or else I'll go back to the original problem? (I've tested it) Once the .mount file is generated, I was thinking that it always works by relying on it.
• Finally, why is this configuration not the default one, am I slowing my startup using it ? Or risking any problem ?

Also, I hope everything is clear on my linked Reddit thread, don't hesitate if you have any question or any question. Thanks again.

from vdo.

Hi @rhawalsh,

Thanks for taking a look and thanks for your reply. I am currently working on this project, so I will modify my script with your suggestion and tell you directly if it works for me.

Edit: yes it works. Thanks.

Great!

Don't worry, it works like a charm once I add the configuration line event_activation = 0 in the LVM configuration file (/etc/lvm/lvm.conf). I'm just curious, which is why I'm wondering:

• Why do I need this systemd .mount file? I was thinking that /etc/fstab was the only configuration needed for permanent/static mounts and the system was dealing with it.

The systemd mount unit is just an alternative to spelling things in /etc/fstab but with additional controls available just like other systemd units.

• Why is all this manipulation not necessary when creating "basic" logical volumes? VDO is just build on top of LVM so it should act the same... Especially since my VDO volumes are active when I create them.

Which manipulations are you speaking of? As you can see we have no special requirements on the mount options anymore. It used to be necessary because we didn't have per-device management controls during startup. With the LVM-VDO implementation, the defaults always worked.

Unless you're talking about the stuff in your script where you were running things like depmod, etc.. In which case, any time you want to have a kernel module available in the initrd, you'd need to do that. Generally speaking, unless you need it in early boot, I think you'd be ok skipping that step.

• Why do I have to keep this event_activation parameter in my lvm.conf or else I'll go back to the original problem? (I've tested it) Once the .mount file is generated, I was thinking that it always works by relying on it.

I'm not sure... The default configuration in RHEL-based distros works as intended. I'm not sure whether event_activation is enabled or disabled by default there and why it needs to be changed on Debian-based distros.

• Finally, why is this configuration not the default one, am I slowing my startup using it ? Or risking any problem ?

I don't know who maintains lvm2 in the Debian-based distros. I don't think it's the same group as those who maintain it in RHEL-based distros. If they're using a different default, then maybe they could explain it (or something in their logs might indicate why)

Also, I hope everything is clear on my linked Reddit thread, don't hesitate if you have any question or any question. Thanks again.

from vdo.

Hello @rhawalsh,
Sorry that I didn't answer, it was a very busy year and 2023 the same...

Which manipulations are you speaking of? As you can see we have no special requirements on the mount options anymore. It used to be necessary because we didn't have per-device management controls during startup. With the LVM-VDO implementation, the defaults always worked.
Unless you're talking about the stuff in your script where you were running things like depmod, etc.. In which case, any time you want to have a kernel module available in the initrd, you'd need to do that. Generally speaking, unless you need it in early boot, I think you'd be ok skipping that step.

Yes I was talking about all of this.

Whatever, I just upgraded to Debian 12 with 6.1.37-1 Linux kernel and LVM 2.03.16-2 and now this configuration (with event_activation = 0) no longer works... I have LVM installed with default configuration but my LVM VDO volumes are inactive at boot... Any idea now I'm no longer using "old kernel" ? (very important for me as I have down services actually in my home lab...)

lvm.conf states that :

# Previously, setting this to zero would enable static autoactivation
# services (via the lvm2-activation-generator), but the autoactivation
# services and generator have been removed.

from vdo.

OMG I think I just found... I had to add "kvdo" to /etc/initramfs-tools/modules so that the module is loaded by initramfs at boot...
Can you confirm that it's a requirement ? And that it's the right way to do it ?

Sources :

• https://unix.stackexchange.com/questions/717763/lvm2-integrity-feature-breaks-lv-activation
• https://askubuntu.com/questions/642454/where-do-i-add-modules-to-initramfs-15-04
• https://www.headdesk.me/LVM

from vdo.