DVB-T2 config issue about mumudvb HOT 8 CLOSED

Hello

This could be a linking issue at compilation, how did you installed your
dvb-t2 driver. Mumudvb detect which bandwidth are supported by the system
at compilation, I will add some message in case it is not supported.

About mumudvb 2.0.0 it is in the mumudvb2 branch

Best
Le 18 mars 2014 08:23, "dtcmumuuser" [email protected] a écrit :

Dear developer!
I installed mumudvb from git. I supposed it would be 2.0, but it shows
version 1.7.3 built with DVB-T2 support. I try to lock with this config
options
delivery_system=DVBT2
freq=514
bandwidth=10MHz
unicast=1
port_http=10007
card=2
I get
"Info: Tune: You will use DVB API version 5 for tuning your card.
ERRO: Tune: Config issue : bandwidth"
Your configuration Readme shows 5Mhz, 10Mhz, 1.712Mhz options for DVB-T2
bandwidth. However, only 6Mhz or 8Mhz seem to be applicable. Those are not
the right values for DVB-T2, but right ones, 5 or 10, give an error.
When I omit bandwidth option the default 8Mhz is used and of course the
card cannot tune
Info: Tune: Tuning DVB-T to 514000000 Hz, Bandwidth: 8000000
Info: Tune: Tuning With DVB-API version 5. delivery system : 16
ERRO: Tune: FE_SET_PROPERTY failed : Invalid argument
Info: Main: Tunning issue, card 2
Info: Main: Closing cleanly. Error 7
Info: Main: ========== MuMuDVB version 1.7.3_20131116_master is stopping
with ExitCode 7 ==========
Please help.
Best wishes,
Pavel.

—
Reply to this email directly or view it on GitHubhttps://github.com//issues/55
.

from mumudvb.

I used the driver provided by the manufacturer (Gotview master HD3 based on rtl8232u + si2168) with the kernel it is said to be working for sure. mumudvb sees the frontend but shuts down as I described. It tries to tune only to default value which is not compatible with the device itself, 8000000. Any other bandwidth setting causes mumudvb to crash. With the default value it crashes, too, but because of the unability of the device to tune on 8Mhz.
I did install mumudvb 2.0.0 from zip. Git 2.0.0 asks for a username and password, 1.7.3 does not.

from mumudvb.

can you explain me how did you installed the driver (and provide me a link
to it) if you compiled MuMuDVB before or after it?

Can you also give the contents of
/usr/include/linux/dvb/frontend.h

My guess is that MuMuDVB was compiled against the kernel and did not see
the driver providing the 10MHz bandwidth

from mumudvb.

I bought a new card with definitely working driver to be on the safe side on a driver issue. As soon as it comes in I check again and reply either it is working or not. Thank you for your prompt replies.

from mumudvb.

Dear Braice,
You were right, it was a driver issue. Thanks for a wonderfule product!

from mumudvb.

Dear Braice,
I tune to a frequency that has Multi PLP in it. I use stream_id for PLP number but whatever id I use I tune to PLP 0 only. What do I do wrong?

from mumudvb.

Once again, it was a driver problem. Everything is working. Thanks again. And thanks to Crazycat for alternative TBS drivers.

from mumudvb.

good morning

from mumudvb.