Feature Request: Code that works for testing 2x Lora Vision Shields about mkrwan HOT 29 CLOSED

Sorry, the firmware binary was not updated...I just pushed a new commit in PR #90 with the updated firmware. Please upload the example MKRWANFWUpdater_standalone with the new binary to update the firmware.
Then, to test the new APIs, an example sketch could be the following. Remember to call modem.begin() with your region, before everything else.

#include <MKRWAN.h>

LoRaModem modem;

void setup() {
  Serial.begin(115200);
  while (!Serial);
  
  if (!modem.begin(EU868)) {
    Serial.println("Failed to start module");
    while (1) {}
  };

  Serial.println("getChannelMask: " + String(modem.getChannelMask()));

  Serial.println("isChannelEnabled(0): " + String(modem.isChannelEnabled(0)));
  Serial.println("isChannelEnabled(1): " + String(modem.isChannelEnabled(1)));
  Serial.println("isChannelEnabled(2): " + String(modem.isChannelEnabled(2)));
  Serial.println("isChannelEnabled(3): " + String(modem.isChannelEnabled(3)));
  Serial.println("isChannelEnabled(4): " + String(modem.isChannelEnabled(4)));

  modem.disableChannel(1);
  modem.enableChannel(4);

  Serial.println("get new ChannelMask: " + String(modem.getChannelMask()));
}

void loop() {

}

from mkrwan.

So, I just tested a possible procedure and I think it could work for you 🙂

1. download this core https://github.com/facchinm/ArduinoCore-stm32l0/tree/vision_shield (vision_shield branch) in your sketchbook/hardware folder (eg. with cd $sketchbook/hardware/mycores && git clone https://github.com/facchinm/ArduinoCore-stm32l0 -b vision_shield)
2. Upload the attached sketch to your Portenta PortentaLoRaBridge-210323a.zip
3. Select "Arduino Portenta Vision Shield" from "Tlera Corp STM32L0 Boards" board entry
4. Upload any sketch after selecting the Portenta serial (this won't overwrite the sketch running on Portenta)
5. I used LoRa_Callbacks example from inside the core and it works great, ping-ponging data between two boards.

Let me know if you need any help!

from mkrwan.

Hi Jeremy,
the "dumb" mode only works for SAMD boards (MKRWAN13x0) since they share SPI and UART pins. One way to bypass the issue is by using this core https://github.com/GrumpyOldPizza/ArduinoCore-stm32l0 and this patch GrumpyOldPizza/ArduinoCore-stm32l0#57 to directly write the Murata module firmware. When doing so the SAMD (or STM32 in the Portenta) can communicate with the module using the standard serial port and you can avoid the LoraWAN stack and talk directly with the radio.

In the meantime, I'm setting up a new API to allow manually changing the channel mask, overriding the default configuration (arduino/mkrwan1300-fw@9479bb9). This would allow sending messages via single channel "gateways" (like ESP32 with LoRa radio)

Hope it helps!

from mkrwan.

Thank you so much @facchinm for looking into this. I have got my LoRanWan Vision Shield connecting in North America on the https://explorer.helium.com/coverage network. I contacted their devs who have purchased the board with a portenta and will try to add Helium support in their arduino LongFi library.

For point-to-point LoRa I am not really sure how to use https://github.com/GrumpyOldPizza/ArduinoCore-stm32l0 with the patch but the LoRa ping/pong example looks exactly what I want. Not really sure what board would work. See Image below.

I will probably wait for you to have something from Arduino that I can test.

from mkrwan.

Hi @hpssjellis, PR #90 adds new APIs to enable/disable channels. Could you please try them and give us some feedback? Thanks!

from mkrwan.

@giulcioffi . I would really like to help test these. Controlling the channel mask should be helpful. Do you have any links to example programs I can try? I really appreciate you working on this.

.

I made a quick attempt to print information but had no luck. Does the channel information need a live connection, I don't think so? Notice I had no printout from getChannelMask.

from mkrwan.

@giulcioffi that worked better. Using this code

#include <MKRWAN.h>

LoRaModem modem;

void myPrintMask(){
 
  Serial.println("Your module version is: " + String(modem.version()) );
  Serial.println("getDataRate: " + String(modem.getDataRate()) );
  Serial.println("getADR: " + String(modem.getADR()) );
  Serial.println("getRX2Freq: " + String(modem.getRX2Freq()) );
  Serial.println("getRX2DR(): " + String(modem.getRX2DR()) );
   
  Serial.println("getDevAddr: " + String(modem.getDevAddr()) );
  Serial.println("getNwkSKey: " + String(modem.getNwkSKey()) );
  Serial.println("getAppSKey: " + String(modem.getAppSKey()) );
  Serial.println("getFCU: " + String(modem.getFCU()) );
  Serial.println("getFCD: " + String(modem.getFCD()) );
  Serial.println("getChannelMask: " + String(modem.getChannelMask()));
  
  Serial.println("isChannelEnabled(0): " + String(modem.isChannelEnabled(0)));
  Serial.println("isChannelEnabled(1): " + String(modem.isChannelEnabled(1)));
  Serial.println("isChannelEnabled(2): " + String(modem.isChannelEnabled(2)));
  Serial.println("isChannelEnabled(3): " + String(modem.isChannelEnabled(3)));
  Serial.println("isChannelEnabled(4): " + String(modem.isChannelEnabled(4)));
  Serial.println("isChannelEnabled(5): " + String(modem.isChannelEnabled(5)));
  Serial.println("isChannelEnabled(6): " + String(modem.isChannelEnabled(6)));
  Serial.println("-------------------------------");
}

void setup() {
  Serial.begin(115200);
  while (!Serial);
  
  if (!modem.begin(US915)) {
    Serial.println("Failed to start module");
    while (1) {}
  };

  Serial.println("For modem.begin(US915)");

  Serial.println("Now Showing default Channels ");
  myPrintMask();

  Serial.println("Now Disabling all channels and enable channel 2 ");
  modem.disableChannel(0);
  modem.disableChannel(1);
  modem.enableChannel(2);
  modem.disableChannel(3);
  modem.disableChannel(4);
  modem.disableChannel(5);
  modem.disableChannel(6);
  myPrintMask(); 

  
  Serial.println("Now enable all channels except 2");
  modem.enableChannel(0); 
  modem.enableChannel(1); 
  modem.disableChannel(2); 
  modem.enableChannel(3); 
  modem.enableChannel(4); 
  modem.enableChannel(5); 
  modem.enableChannel(6); 
  myPrintMask(); 

}

void loop() {

}

I got these results

For modem.begin(US915)
Now Showing default Channels 
Your module version is: ARD-078 1.2.3
getDataRate: 0
getADR: 1
getRX2Freq: 923300000
getRX2DR(): 8
getDevAddr: 00000000
getNwkSKey: 00000000000000000000000000000000
getAppSKey: 00000000000000000000000000000000
getFCU: 0
getFCD: 0
getChannelMask: ffffffffffffffff00ff0000
isChannelEnabled(0): 1
isChannelEnabled(1): 1
isChannelEnabled(2): 1
isChannelEnabled(3): 1
isChannelEnabled(4): 1
isChannelEnabled(5): 1
isChannelEnabled(6): 1
-------------------------------
Now Disabling all channels and enable channel 2 
Your module version is: ARD-078 1.2.3
getDataRate: 0
getADR: 1
getRX2Freq: 923300000
getRX2DR(): 8
getDevAddr: 00000000
getNwkSKey: 00000000000000000000000000000000
getAppSKey: 00000000000000000000000000000000
getFCU: 0
getFCD: 0
getChannelMask: ff84ffffffffffff00ff0000
isChannelEnabled(0): 0
isChannelEnabled(1): 0
isChannelEnabled(2): 1
isChannelEnabled(3): 0
isChannelEnabled(4): 0
isChannelEnabled(5): 0
isChannelEnabled(6): 0
-------------------------------
Now enable all channels except 2
Your module version is: ARD-078 1.2.3 ARD-078
getDataRate: 1
getADR: 0
getRX2Freq: 1
getRX2DR(): 923300000
getDevAddr: 8
getNwkSKey: 00000000
getAppSKey: 00000000000000000000000000000000
getFCU: 0
getFCD: 0
getChannelMask: 0
isChannelEnabled(0): 1
isChannelEnabled(1): 1
isChannelEnabled(2): 0
isChannelEnabled(3): 1
isChannelEnabled(4): 1
isChannelEnabled(5): 1
isChannelEnabled(6): 1
-------------------------------

Possibly the default channelmask should be saved as it looks like it gets lost if you disable all the channels.

P.S. How would code look to use only one channel to allow 2 Portenta's with the Lora Vision Shield to communicate?

from mkrwan.

Hi @hpssjellis, thank you for pointing out this failure on Portenta. getChannelMask() was sometimes failing during the series of channel enabling/disabling operations...I now pushed a commit that should fix this issue.
About the communication between 2 Portenta with the Lora Vision Shield, this will need some additional development since you will need to move from LoraWAN to Lora protocol. You can do this by using a single-channel gateway and the provided APIs.

from mkrwan.

@giulcioffi That is great. I thought it didn't work but then I ran the updater and my code worked great. Here is the new output.

For modem.begin(US915)
Now Showing default Channels 
Your module version is: ARD-078 1.2.3
getDataRate: 0
getADR: 1
getRX2Freq: 923300000
getRX2DR(): 8
getDevAddr: 00000000
getNwkSKey: 00000000000000000000000000000000
getAppSKey: 00000000000000000000000000000000
getFCU: 0
getFCD: 0
getChannelMask: ffffffffffffffff00ff0000
isChannelEnabled(0): 1
isChannelEnabled(1): 1
isChannelEnabled(2): 1
isChannelEnabled(3): 1
isChannelEnabled(4): 1
isChannelEnabled(5): 1
isChannelEnabled(6): 1
-------------------------------
Now Disabling all channels and enable channel 2 
Your module version is: ARD-078 1.2.3
getDataRate: 0
getADR: 1
getRX2Freq: 923300000
getRX2DR(): 8
getDevAddr: 00000000
getNwkSKey: 00000000000000000000000000000000
getAppSKey: 00000000000000000000000000000000
getFCU: 0
getFCD: 0
getChannelMask: ff84ffffffffffff00ff0000
isChannelEnabled(0): 0
isChannelEnabled(1): 0
isChannelEnabled(2): 1
isChannelEnabled(3): 0
isChannelEnabled(4): 0
isChannelEnabled(5): 0
isChannelEnabled(6): 0
-------------------------------
Now enable all channels except 2
Your module version is: ARD-078 1.2.3
getDataRate: 0
getADR: 1
getRX2Freq: 923300000
getRX2DR(): 8
getDevAddr: 00000000
getNwkSKey: 00000000000000000000000000000000
getAppSKey: 00000000000000000000000000000000
getFCU: 0
getFCD: 0
getChannelMask: fffbffffffffffff00ff0000
isChannelEnabled(0): 1
isChannelEnabled(1): 1
isChannelEnabled(2): 0
isChannelEnabled(3): 1
isChannelEnabled(4): 1
isChannelEnabled(5): 1
isChannelEnabled(6): 1
-------------------------------

If you can think of some code to test point to point that would be really useful. I will be testing my own ideas based on sandeepmistrys lora, but using your channel masks

from mkrwan.

@hpssjellis unfortunately the mask is not enough for point to point communication; you can use it to talk with a low cost, single channel gateway (eg. an ESP32 with Semtech radio) that will transparenly forward the data to the cloud.
LoraWAN encryption schemes are compulsory, so the "gateway" board will just receive garbage.
Moreover, the gateway must be able to communicate directly to the radio chip, so we are back to square one (no way to do it using Portenta HW).
The only way to exploit P2P is by writing a very custom firmware for the Murata module, taking this as a starting point.

from mkrwan.

Just checking, @facchinm and @giulcioffi . The Portenta vision shield LoRa hardware limitations, are they simplified with the Breakout board, which does give access to some of the lora chip pins?

Also if I am stuck with Murata chip programming, I would give it a try, I just need a few examples to get started.

from mkrwan.

@facchinm Martino, I really like where this is going.

I have an error running on windows. (I installed the Tlera board then replaced the board code with your repository. Not sure if that is the best method. )

from mkrwan.

Almost there 😄 The PortentaLoRaBridge sketch should be flashed on the Portenta, so you should select Portenta H7 M7 as target. All the other sketches than will run on the Murata if compiled for Vision Shield 😉

from mkrwan.

That makes sense but @facchinm I am getting same error using either the M7 or M4 core. Are you running a newer than 1.3.2 mbed board? Where would I find the Class Uart to check?

from mkrwan.

Ah yes, I'm using an unreleased version of mbed core... You can either use the git version or just wait a bit until we release (hint, will happen soon 😉 )

from mkrwan.

@facchinm Sounds good. I will wait. Thank you so much for looking into this. Your my new Tech Hero.

from mkrwan.

@hpssjellis core 2.0.0 is live and released, so now the sketch should compile just fine 🙂
The release notes are here https://github.com/arduino/ArduinoCore-mbed/releases/tag/2.0.0 if you want to take a look!

from mkrwan.

@facchinm That is big news. Yes I will be testing everything and making more Portenta Videos.

P.S. I am making a Portenta Arduino IDE Library with a bugs folder as I find any. I will also post issues as appropriate.

https://github.com/hpssjellis/portenta-pro-community-solutions/tree/main/examples/z-portenta-bugs

from mkrwan.

@facchinm are you on a Mac on Linux machine? I am having a few serial port issues that look linux based

/dev/ttyS0

I will test from my ubuntu machine tonight. Couple of questions:

1. Do I need an up-to-date MKRWAN library to run MKRWANFWUpdate_standalone? (I don't think so)

2. After running PortentaLoRaBridge using Portenta M7 it looks like you don't double hit the board button to put into bootloader mode. Just keep flashing Tlera code to the board. (I think that is Correct)

3. Everything seems to be fine, just have to get Serial Print running. For now I will try to just use LED's to test.

from mkrwan.

@facchinm Works great on Ubuntu. Ping pong switching master etc. Very impressive.

What is the plan if you can get this working on windows? Can this be made as part of the MBED core or would you push a PR to https://github.com/GrumpyOldPizza/ArduinoCore-stm32l0 ?

from mkrwan.

@facchinm from a memory allocation point of view does this make any sense to you? I have my 2 Portenta LoRa shields Ping and Ponging each other, I then put a normal Machine Learning program on one of the Portenta boards using the normal arduino method. On bootup the boards still ping and pong, even though the machine learning program also runs! If I then clean both the M7 and M4 cores of the that board, it still Ping and Pongs with the original when powered. If I shut down the cleaned board, the Ping Pong stops. Weird.

Basically really resilient. I can't stop it from being able to ping/pong. Any idea how to clean it? I even fired up OpneMV and it still ping/pongs but only when powered.

If I load your Tlera core, I can flash a blank program which stops the 2nd board from ping/pong. Has your Tlera Core created a permanent thread like a virtual 3rd core?

from mkrwan.

Super happy you made it working 🎉 !
Basically, the Tlera Core flashes directly the STM32L0 in the murata module, so unless you keep the module under reset, the sketch flashed on that core will keep running 🙂
The "right" way to do this would be adding an RPC like interface to both the L0 and the H7 (using a library like https://github.com/openmv/openmv-arduino-rpc with SerialLora as transport) and trigger the LoRa functionality on demand.
Let me know if you need any help in doing this 😉

from mkrwan.

I will look into the RPC library as I need to get information from the M7 core to the murata module, thank you @facchinm.

One quick question: On the MKRWAN library the DevEui was generated by the library. In the GrumpyOldPizza library there does not seem to be that ability. Do I just let TTN determine the DevEui?

from mkrwan.

Sure, DevEUI is a sorf of mac address, so you shouldn't join the same network with two boards sharing it. TTN takes care there's no duplicate when they assign it so it's all fine 😉

from mkrwan.

@facchinm just an update here. I seem to be able to communicate with the murata module from the Portenta using UART3. That seems to be connected to the murata module regular Serial. Still testing if I can send data using UART3 to the murata module.

#include "mbed.h"

UART mySerial3(PJ_8,  PJ_9,  NC, NC);


// in the main loop from the portenta

  if (mySerial3.available()) {    
     Serial.write(mySerial3.read());  
  }

from mkrwan.

@facchinm I had this bright idea to fork your version of the grumpyOldPizza library at https://github.com/facchinm/ArduinoCore-stm32l0 add several Portenta Specific examples here and then submit a PR back to grumpyOldPizza to include in his library.

Unfortunately I have just clued in that your fork is very raw and not at all ready for a PR back to the master. It is probably a fair bit of work to make it ready and that is a waste of your time. I thrive on wasting time.

You have basically just changed:

boards.txt

and the

B-L072Z-LRWAN1 variant.cpp file for each of the Arduino boards.

Is there anything else you changed or is that it? Is this something you would eventually submit as a PR or somehow include with the Arduino MBED boards or is this something I might be able to submit as a PR to grumpOldPizza? It looks like I just have to make a B-L072Z-LRWAN1 folder for each of the Arduino boards and then use your board.txt file and link everything to the new folders.

from mkrwan.

@giulcioffi , @facchinm your version of the grumpyOldPizza library is very cool, any chance it will ever bit a bit more mainstream and give support for all the arduino mbed devices?

I am having a lot of success with both Portenta P2P and LoRaWan, my plan is to make a P2P system which switches to the LoRaWan system when needed. My proof of concept is running. Unfortunately the Murarta module memory seems to die at 0x08010000 is there any way to give it a bit more space?

from mkrwan.

I would like to distribute to friends my .bin or .dfu files made using @facchinm version of the GrumpyOldPizza Tlera board. Does anyone know how to upload these files to the Portenta from the command line on windows. The problem is going to be getting them to load to the correct memory location and if I can just use a regular arduino uploader?

Here is the load command that my linux computer generated

/root/Arduino/hardware/mycores/ArduinoCore-stm32l0-vision_shield/tools/linux/stm32flash /dev/ttyACM0 -e 512 -b 2400 -w /tmp/arduino_build_519314/mySketchName.ino.dfu
stm32flash 0.5

Developing with LoRaWan is incredibly frustrating as you always have to rely on other peoples gateways. What @facchinm has got working with LoRa is very exciting.

It is much too hard to teach others how to work with the GrumpOldPizza method, which as far as I can tell needs a linux computer but giving people my code would work fine.

Seems to be some information here in the installation folder for windows

@echo off
set count=1
:wait
    "%~dp0\dfu-util.exe" -l -d 0483:df11 | findstr "Found" >NUL 2>&1
    if %errorlevel% == 0 ( 
	"%~dp0\dfu-util.exe" -d %1:%2,0x0483:0xdf11 -a 0 -s 0x08000000:leave -D %3
    ) else (
        if %count% gtr 10 goto break 
        echo %count%
        set /A count+=1
        ping -n 1 127.0.0.1 >NUL
        goto :wait
    )
)

:break

Whereas on my window machine the code looks something like

C:\Users\myUser.name\AppData\Local\Arduino15\packages\arduino\tools\dfu-util\0.10.0-arduino1/dfu-util --device 0x2341:0x035b -D C:\Users\myUser~ful.name\AppData\Local\Temp\arduino_build_538244/sketch_dec17a.ino.bin -a0 --dfuse-address=0x08040000:leave 
dfu-util 0.10-dev

Can someone take the above windows command and adapt it to upload the GrumpOldPizza binary.dfu file ?

P.S. I assume dfu-util can take both .bin and .dfu files.

.

So I tried this command on the windows dos prompt after moving the linux .dfu file into my downloads folder

C:\Users\myUser.name\AppData\Local\Arduino15\packages\arduino\tools\dfu-util\0.10.0-arduino1/dfu-util  -d 512:2400,0x0483:0xdf11    -D C:\Users\myUser.name\Downloads\arduino_build_519314\arduino_build_519314/v0.4.0-send-ok-E.ino.dfu -a 0 -s 0x08000000:leave

Not really sure if the Portenta should be in boot mode or regular mode as on the linux computer we install a bridge file to the portenta and then run grumpyOldPizza. I will try to test out if my command line is working.

Also downloaded onto windows stm32flash and tried

stm32flash COM5 -e 512 -b 2400 -w "C:\Users\myUser.name\Downloads\arduino_build_519314\arduino_build_519314/v0.4.0-send-ok-E.ino.dfu"

from mkrwan.

@facchinm I think you might be proud of me.

Looks like if I install xxd and run

echo -n "const " > fw.h && xxd -i myGrumpyCompiledFile.dfu >> fw.h

and replace the following file:

https://github.com/arduino-libraries/MKRWAN/blob/master/examples/MKRWANFWUpdate_standalone/fw.h

I can convert my GrumpyOldPizza .dfu files made on a linux computer to a header file then change the 2 variables to the following:

const unsigned char mlm32l07x01_bin[] 
unsigned int mlm32l07x01_bin_len 

and using a windows computer and the program MKRWANFWUpdate_standalone with the new fw.h file looks like it loads onto the Portenta Boards from a windows computer. In my case I can publish the fw.h files to my students who don't have linux computers. (95% of them don't have linux computers)

from mkrwan.